KIA Sedona (2018 year). Instruction — part 29

What to do in an emergency

Road warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

• Hazard warning flasher . . . . . . . . . . . . . . . . . . . . . . . . 6-2

In case of an emergency while driving. . . . . . . . . . 6-3

• If the engine stalls at a crossroad or crossing. . . . . . . 6-3
• If you have a flat tire while driving . . . . . . . . . . . . . . . 6-3
• If the engine stalls while driving . . . . . . . . . . . . . . . . . 6-3

If the engine does not start . . . . . . . . . . . . . . . . . . . 6-4

• If engine doesn't turn over or turns over slowly . . . . 6-4
• If engine turns over normally but does not start . . . . 6-4

Emergency starting . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

• Jump starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
• Push-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

If the engine overheats. . . . . . . . . . . . . . . . . . . . . . . 6-8
Tire Pressure Monitoring System (TPMS) . . . . . . 6-9

• Changing a tire with TPMS . . . . . . . . . . . . . . . . . . . . 6-12

If you have a flat tire . . . . . . . . . . . . . . . . . . . . . . . 6-15

• Jack and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
• Removing the spare tire . . . . . . . . . . . . . . . . . . . . . . . 6-16
• Storing the spare tire. . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
• Changing tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18

Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25

• Towing service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
• Removable towing hook (front) . . . . . . . . . . . . . . . . . 6-26
• Emergency towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27

6

What to do in an emergency

2

6

ROAD WARNING

Hazard warning flasher

The hazard warning flasher serves
as a warning to other drivers to exer-
cise extreme caution when
approaching, overtaking, or passing
your vehicle.

It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
Depress the flasher switch with the
ignition switch in any position. The
flasher switch is located in the center
facia panel. All turn signal lights will
flash simultaneously.

• The hazard warning flasher oper-

ates whether your vehicle is run-
ning or not.

• The turn signals do not work when

the hazard flasher is on.

• Care must be taken when using

the hazard warning flasher while
the vehicle is being towed.

OYP064001N

OYP064014K

■

Type A

■

Type B

6 3

What to do in an emergency

If the engine stalls at a cross-
road or crossing

If the engine stalls at a crossroad or
crossing, set the shift lever in the N
(Neutral) position and then push the
vehicle to a safe place.

If you have a flat tire while
driving

If a tire goes flat while you are driv-
ing:
1.Take your foot off the accelerator

pedal and let the vehicle slow
down while driving straight ahead.
Do not apply the brakes immedi-
ately or attempt to pull off the road
as this may cause a loss of control.
When the vehicle has slowed to
such a speed that it is safe to do
so, brake carefully and pull off the
road. Drive off the road as far as
possible and park on a firm level
ground. If you are on a divided
highway, do not park in the median
area between the two traffic lanes.

2.When the vehicle is stopped, turn

on your emergency hazard flash-
ers, set the parking brake and put
the transaxle in P (Park, automatic
transaxle).

3.Have all passengers get out of the

vehicle. Be sure they all get out on
the side of the vehicle that is away
from traffic.

4.When changing a flat tire, follow

the instruction provided later in this
section.

If the engine stalls while driving

1.Reduce your speed gradually,

keeping a straight line. Move cau-
tiously off the road to a safe place.

2.Turn on your emergency flashers.
3.Try to start the engine again. If your

vehicle will not start, contact an
authorized Kia dealer or seek other
qualified assistance.

✽

✽

NOTICE

If there was a check engine light and
loss of power or stall and if safe to do
so wait at least 10 seconds to restart
the vehicle after it stalls. This may
reset the car so it will no longer run
at low power (limp home) condition.

IN CASE OF AN EMERGENCY WHILE DRIVING

What to do in an emergency

4

6

IF THE ENGINE WILL NOT START

If engine doesn't turn over or
turns over slowly

1.If your vehicle has an automatic

transaxle, be sure the shift lever is
in N (Neutral) or P (Park) and the
emergency brake is set.

2.Check the battery connections to

be sure they are clean and tight.

3.Turn on the interior light. If the light

dims or goes out when you operate
the starter, the battery is dis-
charged.

4.Check the starter connections to

be sure they are securely tight-
ened.

5.Do not push or pull the vehicle to

start it. See instructions for "Jump
starting".

If engine turns over normally
but does not start

1.Check the fuel level.
2.With the ignition switch in the

LOCK position, check all connec-
tors at the ignition coils and spark
plugs. Reconnect any that may be
disconnected or loose.

3.Check the fuel line in the engine

compartment.

4.If the engine still does not start, call

an authorized Kia dealer or seek
other qualified assistance.

WARNING

- Push /

Pull start

Do not push or pull the vehicle
to start it. Push or pull starting
may cause the catalytic con-
verter to overload and create a
fire hazard.

6 5

What to do in an emergency

EMERGENCY STARTING

Connect cables in numerical order
and disconnect in reverse order.

Jump starting

Jump starting can be dangerous if
done incorrectly. Therefore, to avoid
harm to yourself or damage to your
vehicle or battery, follow these jump
starting procedures. If in doubt, we
strongly recommend that you have a
competent technician or towing serv-
ice jump start your vehicle.

CAUTION

- 12 volt battery

Use only a 12-volt jumper sys-
tem. You can damage a 12-volt
starting motor, ignition system,
and other electrical parts
beyond repair by use of a 24-
volt power supply (either two
12-volt batteries in series or a
24-volt motor generator set).

WARNING

- Battery

Never attempt to check the elec-
trolyte level of the battery as
this may cause the battery to
rupture or explode.

WARNING

- Frozen

batteries

Do not attempt to jump start the
vehicle if the discharged battery
is frozen or if the electrolyte
level is low as the battery may
rupture or explode.

1VQA4001

(-)

(+)

(+)

(-)

Discharged

battery

Jumper Cables

Booster
battery

What to do in an emergency

6

6

Jump starting procedure

1.Make sure the booster battery is

12-volt and that its negative termi-
nal is grounded.

2.If the booster battery is in another

vehicle, do not allow the vehicles to
come in contact.

3.Turn off all unnecessary electrical

loads.

4.Connect the jumper cables in the

exact sequence shown in the illus-
tration. First connect one end of a
jumper cable to the positive termi-
nal of the discharged battery (1),
then connect the other end to the
positive terminal of the booster
battery (2).
Proceed to connect one end of the
other jumper cable to the negative
terminal of the booster battery (3),
then the other end to a solid, sta-
tionary, metallic point (for example,
the engine lifting bracket) away
from the battery (4). Do not con-
nect it to or near any part that
moves when the engine is cranked.

Do not allow the jumper cables to
contact anything except the correct
battery terminals or the correct
ground. Do not lean over the bat-
tery when making connections.

WARNING

- Sulfuric acid

risk

When jump starting your vehicle
be careful not to get acid on
yourself, your clothing or on the
vehicle. Automobile batteries
contain sulfuric acid. This is poi-
sonous and highly corrosive.

WARNING

- Battery

Keep all flames or sparks away
from the battery. The battery
produces hydrogen gas which
will explode if exposed to flame
or sparks.

WARNING

- Battery

cables

Do not connect the jumper cable
from the negative terminal of the
booster battery to the negative
terminal of the discharged bat-
tery. This can cause the dis-
charged battery to overheat and
crack, releasing battery acid.
Make sure to connect one end
of the jumper cable to the nega-
tive terminal of the booster bat-
tery, and the other end to a
metallic point, far away from the
battery.

6 7

What to do in an emergency

5.Start the engine of the vehicle with

the booster battery and let it run at
2,000 rpm, then start the engine of
the vehicle with the discharged
battery.

If the cause of your battery discharg-
ing is not apparent, you should have
your vehicle checked by an author-
ized Kia dealer.

Push-starting

Vehicles equipped with automatic
transaxle lock system cannot be
push-started.
Follow the directions in this section
for jump-starting.

WARNING

- Tow starting

vehicle

Never tow a vehicle to start it
because the sudden surge for-
ward when the engine starts
could cause a collision with the
tow vehicle.

What to do in an emergency

8

6

IF THE ENGINE OVERHEATS

If your temperature gauge indicates
overheating, you experience a loss
of power, or hear loud pinging or
knocking, the engine will probably be
too hot. If this happens, you should:

1.Pull off the road and stop as soon

as it is safe to do so.

2.Place the shift lever in P (Park,

automatic transaxle) and set the
parking brake. If the air condition-
ing is on, turn it off.

3.If engine coolant is running out

under the vehicle or steam is com-
ing out from underneath the hood,
stop the engine. Do not open the
hood until the coolant has stopped
running or the steaming has
stopped. If there is no visible loss
of engine coolant and no steam,
leave the engine running and
check to be sure the engine cool-
ing fan is operating. If the fan is not
running, turn the engine off.

4.Check to see if the water pump

drive belt is missing. If it is not
missing, check to see that it is
tight. If the drive belt seems to be
satisfactory, check for coolant leak-
ing from the radiator, hoses or
under the vehicle. (If the air condi-
tioning had been in use, it is nor-
mal for cold water to be draining
from it when you stop).

5.If the water pump drive belt is bro-

ken or engine coolant is leaking
out, stop the engine immediately
and call the nearest authorized Kia
dealer for assistance.

6.If you cannot find the cause of the

overheating, wait until the engine
temperature has returned to nor-
mal. Then, if coolant has been lost,
carefully add coolant to the reser-
voir to bring the fluid level in the
reservoir up to the halfway mark.

7.Proceed with caution, keeping

alert for further signs of overheat-
ing. If overheating happens again,
call an authorized Kia dealer for
assistance.

Serious loss of coolant indicates
there is a leak in the cooling system
and this should be checked as soon
as possible by an authorized Kia
dealer.

WARNING

- Under the

hood

While the engine is running,
keep hair, hands and clothing
away from moving parts such
as the fan and drive belts to pre-
vent injury.

WARNING

- Radiator cap

Do not remove the radiator cap
when the engine is hot. This
may result in coolant being
blown out of the opening and
cause serious burns.

6 9

What to do in an emergency

TIRE PRESSURE MONITORING SYSTEM (TPMS)

(1) Low tire pressure telltale /

TPMS malfunction indicator

Each tire, including the spare (if pro-
vided), should be checked monthly
when cold and inflated to the inflation
pressure recommended by the vehicle
manufacturer on the vehicle placard or
tire inflation pressure label. (If your
vehicle has tires of a different size than
the size indicated on the vehicle plac-
ard or tire inflation pressure label, you
should determine the proper tire infla-
tion pressure for those tires.)

As an added safety feature, your
vehicle has been equipped with a tire
pressure monitoring system (TPMS)
that illuminates a low tire pressure
telltale when one or more of your
tires is significantly under-inflated.
Accordingly, when the low tire pres-
sure telltale illuminates, you should
stop and check your tires as soon as
possible, and inflate them to the
proper pressure. Driving on a signifi-
cantly under-inflated tire causes the
tire to overheat and can lead to tire
failure. Under-inflation also reduces
fuel efficiency and tire tread life, and
may affect the vehicle’s handling and
stopping ability.

Please note that the TPMS is not a
substitute for proper tire maintenance,
and it is the driver’s responsibility to
maintain correct tire pressure, even if
under-inflation has not reached the
level to trigger illumination of the
TPMS low tire pressure telltale.

Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not oper-
ating properly. The TPMS malfunction
indicator is combined with the low tire
pressure telltale. When the system
detects a malfunction, the telltale will
flash for approximately one minute
and then remain continuously illumi-
nated. This sequence will continue
upon subsequent vehicle start-ups as
long as the malfunction exists. When
the malfunction indicator is illuminat-
ed, the system may not be able to
detect or signal low tire pressure as
intended. TPMS malfunctions may
occur for a variety of reasons, includ-
ing the installation of replacement or
alternate tires or wheels on the vehi-
cle that prevent the TPMS from func-
tioning properly. Always check the
TPMS malfunction telltale after
replacing one or more tires or wheels
on your vehicle to ensure that the
replacement or alternate tires and
wheels allow the TPMS to continue to
function properly.

OYP064002K

What to do in an emergency

10

6

✽

✽

NOTICE

If the TPMS, Low Tire Pressure
indicator do not illuminate for 3 sec-
onds when the ignition switch is
turned to the ON position or engine
is running, or if they remain illumi-
nated after coming on for approxi-
mately 3 seconds, take your vehicle
to your nearest authorized Kia deal-
er and have the system checked.

Low tire pressure tell-
tale

When the tire pressure monitoring
system warning indicators are illumi-
nated, one or more of your tires is
significantly under-inflated.
If the telltale illuminates, immediately
reduce your speed, avoid hard cor-
nering and anticipate increased stop-
ping distances. You should stop and
check your tires as soon as possible.
Inflate the tires to the proper pres-
sure as indicated on the vehicle’s
placard or tire inflation pressure label
located on the driver’s side center pil-
lar outer panel. If you cannot reach a
service station or if the tire cannot
hold the newly added air, replace the
low pressure tire with the spare tire.

Then the TPMS malfunction indicator
and the Low Tire Pressure telltale
may turn on and illuminate after
restarting and about 20 minutes of
continuous driving before you have
the low pressure tire repaired and
replaced on the vehicle.
In winter or cold weather, the low tire
pressure telltale may be illuminated if
the tire pressure was adjusted to the
recommended tire inflation pressure
in warm weather. It does not mean
your TPMS is malfunctioning
because the decreased temperature
leads to a proportional lowering of
tire pressure.
When you drive your vehicle from a
warm area to a cold area or from a
cold area to a warm area, or the out-
side temperature is greatly higher or
lower, you should check the tire infla-
tion pressure and adjust the tires to
the recommended tire inflation pres-
sure.

CAUTION

• The tire pressure may change

due to factors such as parking
condition, driving style, and
altitude above sea level.

• Low tire pressure warning may

sound when a tire’s pressure
unit is equal or higher than
nearby tires. This is a normal
occurrence, which is due to the
change in tire pressure along
with tire temperature.

• The tire pressure shown on

the dashboard may differ from
the tire pressure measured by
tire pressure gauge.

6 11

What to do in an emergency

TPMS (Tire Pressure
Monitoring System)
malfunction indicator

The low tire pressure telltale will illu-
minate after it blinks for approximate-
ly one minute when there is a prob-
lem with the Tire Pressure
Monitoring System. If the system is
able to correctly detect an underinfla-
tion warning at the same time as sys-
tem failure then it will illuminate both
the TPMS malfunction and low tire
pressure position telltales e.g. if
Front Left sensor fails, the TPMS
malfunction indicator illuminates, but
if the Front Right, Rear Left, or Rear
Right tire is under-inflated, the low
tire pressure position telltales may
illuminate together with the TPMS
malfunction indicator.
Have the system checked by an
authorized Kia dealer as soon as
possible to determine the cause of
the problem.

• The TPMS malfunction indicator

may be illuminated if the vehicle is
moving around electric power sup-
ply cables or radios transmitters
such as at police stations, govern-
ment and public offices, broadcast-
ing stations, military installations,
airports, or transmitting towers,
etc. This can interfere with normal
operation of the Tire Pressure
Monitoring System (TPMS).

• The TPMS malfunction indicator

may be illuminated if snow chains
are used or some separate elec-
tronic devices such as notebook
computer, mobile charger, remote
starter or navigation etc., are used
in the vehicle. This can interfere
with normal operation of the Tire
Pressure Monitoring System
(TPMS).

WARNING

- Low pressure

damage

Do not drive on low pressure
tires. Significantly low tire pres-
sure can cause the tires to over-
heat and fail making the vehicle
unstable resulting in increased
braking distances and a loss of
vehicle control.

What to do in an emergency

12

6

Changing a tire with TPMS

If you have a flat tire, the Low Tire
Pressure telltale will come on. Have
the flat tire repaired by an authorized
Kia dealer as soon as possible or
replace the flat tire with the spare tire.

Each wheel is equipped with a tire
pressure sensor mounted inside the
tire behind the valve stem. You must
use TPMS specific wheels. It is rec-
ommended that you always have
your tires serviced by an authorized
Kia dealer.
Even if you replace the low pressure
tire with the spare tire, the Low Tire
Pressure telltale will remain on until
the low pressure tire is repaired and
placed on the vehicle.
After you replace the low pressure
tire with the spare tire, the TPMS
malfunction indicator may illuminate
after a few minutes because the
TPMS sensor mounted on the spare
wheel is not initiated.

Once the low pressure tire is reinflat-
ed to the recommended pressure
and installed on the vehicle or the
TPMS sensor mounted on the
replaced spare wheel is initiated by
an authorized Kia dealer, the TPMS
malfunction indicator and the low tire
pressure telltale will extinguish within
a few minutes of driving.
If the indicator is not extinguished
after a few minutes of driving, please
visit an authorized Kia dealer.
If an original mounted tire is replaced
with the spare tire, the TPMS sensor
on the replaced spare wheel should
be initiated and the TPMS sensor on
the original mounted wheel should be
deactivated. If the TPMS sensor on
the original mounted wheel located in
the spare tire carrier still activates,
the tire pressure monitoring system
may not operate properly. Have the
tire with TPMS serviced or replaced
by an authorized Kia dealer.

CAUTION

- Repair Agents

Never use a puncture-repairing
agent not approved by Kia to
repair and/or inflate a low pres-
sure tire. The tire sealant not
approved by Kia may damage
the tire pressure sensor.

6 13

What to do in an emergency

You may not be able to identify a low
tire by simply looking at it. Always
use a good quality tire pressure
gauge to measure the tire's inflation
pressure. Please note that a tire that
is hot (from being driven) will have a
higher pressure measurement than a
tire that is cold (from sitting station-
ary for at least 3 hours and driven
less than 1 mile (1.6 km) during that
3 hour period).
Allow the tire to cool before measur-
ing the inflation pressure. Always be
sure the tire is cold before inflating to
the recommended pressure.
A cold tire means the vehicle has
been sitting for 3 hours and driven for
less than 1 mile (1.6 km) in that 3
hour period.
Do not use any tire sealant if your
vehicle is equipped with a Tire
Pressure Monitoring System. The liq-
uid sealant can damage the tire
pressure sensors.

• The TPMS cannot alert you to

severe and sudden tire damage
caused by external factors such as
nails or road debris.

• If you feel any vehicle instability,

immediately take your foot off the
accelerator, apply the brakes grad-
ually and with light force, and slow-
ly move to a safe position off the
road.

✽

✽

NOTICE

- Protecting TPMS

Tampering with, modifying, or dis-
abling the Tire Pressure Monitoring
System (TPMS) components may
interfere with the system's ability to
warn the driver of low tire pressure
conditions and/or TPMS malfunc-
tions. Tampering with, modifying,
or disabling the Tire Pressure
Monitoring System (TPMS) compo-
nents may void the warranty for
that portion of the vehicle.

What to do in an emergency

14

6

This device complies with Part
15 of the FCC rules.

Operation is subject to the following
two conditions:
1.This device may not cause harmful

interference, and

2.This device must accept any inter-

ference received, including inter-
ference that may cause undesired
operation.

6 15

What to do in an emergency

IF YOU HAVE A FLAT TIRE

Jack and tools

The jack and wheel lug nut wrench
are stored in the luggage compart-
ment.
Remove the panel indicated in the
illustration.
(1) Jack
(2) Wheel lug nut wrench

(Jack handle)

Jacking instructions

The jack is provided for emergency
tire changing only.
To prevent the jack from “rattling”
while the vehicle is in motion, store it
properly.
Follow jacking instructions to reduce
the possibility of personal injury.

• Always move the vehicle complete-

ly off the road and onto the shoul-
der before trying to change a tire.
The jack should be used on a firm
level ground. If you cannot find a
firm, level place off the road, call a
towing service company for assis-
tance.

• Be sure to use the correct front and

rear jacking positions on the vehi-
cle; never use the bumpers or any
other part of the vehicle for jack
support.

• Do not allow anyone to remain in

the vehicle while it is on the jack.

• Make sure any children present

are in a secure place away from
the road and from the vehicle to be
raised with the jack.

WARNING

- Changing tires

Never attempt vehicle repairs in
the traffic lanes of a public road
or highway.

OYP064029N

WARNING

- Tire Jack

Do not place any portion of your
body under a vehicle that is only
supported by a jack since the
vehicle can easily roll off the
jack. Use vehicle support stands.

What to do in an emergency

16

6

Removing the spare tire

Your spare tire is stored underneath
your vehicle, directly below the right
sliding door.
1. Open the right sliding door and

find the plastic hex bolt cover on
the floor.

2. Remove the cover.

3. Use the wheel lug nut wrench to

loosen the bolt enough to lower
the spare tire.

Turn the wrench counterclockwise

until the spare tire reaches the
ground.

OYP054167N

OYP054163N

WARNING

- Running vehicle on jack

Do not start or run the engine of
the vehicle while the vehicle is
on the jack as this may cause
the vehicle to fall off the jack.