KIA Sedona (2018 year). Instruction — part 35
7 69
Maintenance
3. Check the removed fuse; replace it
if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4. Push in a new fuse of the same
rating, and make sure it fits tightly
in the clips. If it fits loosely, consult
an authorized Kia dealer.
Main fuse
If the main fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Remove the nuts shown in the pic-
ture above.
4. Replace the fuse with a new one
of the same rating.
5. Reinstall in the reverse order of
removal.
CAUTION
- Fuse panel
covers
After checking the fuse panel in
the engine compartment,
securely install the fuse panel
cover. If not, electrical failures
may occur from water contact.
OYP074052N
Maintenance
70
7
Fuse/relay panel description
Inside the fuse/relay panel covers,
you can find the fuse/relay label
describing fuse/relay name and
capacity.
✽
✽
NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle. It is accurate at the
time of printing. When you inspect
the fuse panel in your vehicle, refer
to the fuse panel label.
OYP076014
OYP075015N
7 71
Maintenance
Inner fuse panel
Fuse Name
Fuse rating
Circuit Protected
ECU
10A
PCM, Injector Drive Box, Smart Key Control Module/Immobilizer Module
MODULE4
7.5A
Head Lamp Leveling Device Actuator LH/RH, Multipurpose Check Connector, Bezel Switch, MTS
Module, Electro Chromic, A/V & Navigation Head Unit, A/C Control Module, Heater Control Module,
Passenger Ventilation Seat Control Module, Driver IMS Control Module, Rear Seat Heater Control
Module, Auto Head Leveling Device Module, ATM Shift Lever ILL.
MODULE3 10A
LDWS Module, Stop Lamp, Front Parking Assist Sensor LH/RH, Front Parking Assist Sensor LH/RH
(CENTER), Rear Parking Assist Buzzer, Rear Parking Assist Sensor LH/RH, Rear Parking Assist
Sensor LH/RH (CENTER), Blind Spot Detection Radar LH/RH
MODULE5 7.5A
Rear Seat Heater Control Module, AC Inverter Unit, Heater Control Module, Passenger Ventilation Seat
Control Module, Portable Lamp, Around View Unit
MODULE6
7.5A
BCM, Smart Key Control Module
WIPER RR
15A
Rear Wiper Motor, Wiper RR Relay
CLUSTER 7.5A
Instrument
Cluster
A/CON1
7.5A
A/C Control Module, Ionizer, Rear A/C Control Switch, PCB Block (Blower Relay, Blower RR Relay)
MEMORY2 10A
Data Link Connector, Instrument Cluster, Digital Clock, A/C Control Module, BCM, Power Sliding Door
Module, Driver Door Module, Passenger Safety Power Window Switch, Driver IMS Control Module
SMART KEY3
10A
Start/Stop Button Switch, Immobilizer Module
POWER OUTLET2
20A
Console Power Outlet
A/BAG IND
7.5A
Instrument Cluster, Digital Clock, A/C Control Module(Auto)
WASHER
15A
Multifunction Switch, BCM
HEATED STEERING
15A
Clock Spring (Steering Wheel Switch)
MEMORY1
10A
Clock Spring (Steering Wheel Switch)
SMART KEY1
25A
Smart Key Control Module
POWER OUTLET3
20A
Rear Power Outlet
MODULE2
7.5A
BCM, Driver Door Module, Passenger Door Module
Maintenance
72
7
Fuse Name
Fuse rating
Circuit Protected
MULTIMEDIA
15A
USB Charger #1/#2, MTS Module, Audio, A/V & Navigation Head Unit
S/ROOF FRT
20A
Front Sunroof Motor
AMP 25A
AMP
IG1
20A
PCB BLOCK (Fuse - ABS3, TCU, MDPS, CRUISE)
SMART KEY2
7.5A
Smart Key Control Module
INTERIOR LAMP
10A
Portable Lamp, Overhead Console Lamp, Cargo Lamp, Front Vinity Lamp Switch LH/RH, Glove Box
Lamp, Key Warning Switch
START
7.5A
With IMMO./Smart Key : Transmission Range Switch, W/O IMMO. : PCB Block (B/Alarm Relay)
S/ROOF RR
25A
Rear Sunroof Motor
DOOR LOCK
20A
Tail Gate Relay, Door Lock/Unlock Relay, Sliding Door Lock/Unlock Relay
FOG LAMP REAR
10A
-
MODULE1 10A
Audio, A/V & Navigation Head Unit, Around View Unit, BCM, Overhead Console Lamp, MTS Module,
Digital Clock, USB Charger #1/#2
AIR BAG
15A
SRS Control Module, Passenger Occupant Detection Sensor
A/CON2
7.5A
A/C Control Module, Blower Resistor (Manual)
HEATED MIRROR
10A
Passenger Power Outside Mirror, A/C Control Module
BRAKE SWITCH
7.5A
Smart Key Control Module, Stop Lamp Switch
P/WINDOW
LH
25A
Driver Safety Window Module, Driver Door Module, Rear Power Window Switch LH, Rear Safety Power
Window Switch LH, Rear Safety Power Window Module LH
MODULE7 7.5A
Key Inter Lock Solenoid, Fuel Lid Switch, ATM Lever Switch, Rear A/C Control Switch, Electro Chromic
Mirror
POWER OUTLET1
20A
Front Power Outlet
P/SEAT (DRV)
30A
Driver Manual Switch, Driver Lumbar Support Switch, Driver IMS Control Module
P/WINDOW
RH
25A
Passenger Safety Window Module, Passenger Power Window Motor, Passenger Door Module, Rear
Power Window Switch RH, Rear Safety Power Window Switch RH, Rear Safety Power Window Module
RH
S/HEATER FRT
20A
Heater Control Module, Passenger Ventilation Seat Control Module
7 73
Maintenance
Engine compartment fuse panel
OYP074053K
OYP074034N
Maintenance
74
7
Engine compartment fuse panel
Fuse Name
Fuse rating
Circuit Protected ]
ABS1
40A
ESC Module, Multipurpose Check Connector
ABS2
40A
ESC Module
INVERTER
30A
AC Inverter Unit
IDB
15A
Injector Drive Box
S/HEATER RR
25A
Rear Seat Heater Control Module
FOG LAMP FRONT
15A
Fog Lamp Front Relay
P/SEAT (PASS)
30A
Passenger Manual Switch
COOLING FAN1
60A
Cooling Fna1 Relay
COOLING FAN2
50A
Cooling Fna2 Relay
B+4
50A
Smart Junction Block (IPS Control Module, IPS3, IPS4, IPS5, IPS6, Fuse - MODULE7)
POWER TAIL GATE
40A
Power Tail Gate Module
B+2
50A
Smart Junction Block (Leak Current Autocut Device, Fuse - P/SEAT DRV, P/WDW RH)
IG1
40A
With Smart Key : PDM1/2 Relay, W/O Smart Key : Ignition Switch
IG2
40A
Start Relay, With Smart Key : PDM3 Relay, W/O Smart Key : Ignition Switch,
B+1
50A
Smart Junction Block (IPS Control Module, Fuse - P/WDW LH, S/HEATER FRT, DR LOCK)
TRAILER
30A
Trailer Power Outlet
B+5
50A
Smart Junction Block (Motor Driver, Power Outlet Relay, Fuse - S/ROOF FRT, S/ROOF RR, BRAKE
SWITCH, SMART KEY1, SMART KEY3, AMP)
PSD1
40A
Power Sliding Door Module
PSD2
40A
Power Sliding Door Module
B+3
50A
Smart Junction Block (IPS Control Module, IPS1, IPS2)
MDPS
125A
MDPS Unit (Rack)
7 75
Maintenance
Fuse Name
Fuse rating
Circuit Protected
BLOWER RR
40A
Blower RR Relay
BLOWER
40A
Blower Relay
SENSOR (B+)
10A
Battery Sensor
B/ALARM HORN
10A
B/Alarm Horn Relay
FUEL LID
10A
Fuel Lid Relay
DEICER
15A
Deicer Relay
FUEL PUMP
15A
Fuel Pump Relay
HORN 15A
Horn
Relay
WIPER 25A
Front
Wiper
(Low)
Relay
ECU3
30A
Engine Control Relay, Fuse - ECU1
REAR HEATED
40A
Rear Heated Relay
TCU
15A
Transmission Range Switch
MDPS
10A
MDPS Unit (Rack)
CRUISE
10A
Smart Cruise Control Radar
B/UP LAMP
10A
Audio, A/V & Navigation Head Unit, Rear Combination Lamp (IN) LH/RH, Electro Chromic Mirror
A/CON
7.5A
Rear A/C Control Switch, A/C Control Module
ECU1 15A
PCM
ABS3
7.5A
ESC Module, Steering Angle Sensor
ECU2
10A
Injector Drive Box
SENSOR1
15A
Oxygen Sensor #1/#2/#3/#4, PCM, E/R Junction Box (Cooling Fan1 Relay)
SENSOR2 10A
PCM, Canister Close Valve, Variable Intake Solenoid Valve #1/#2, Purge Control Solenoid Valve, Oil Control
Valve #1/#2 (Intake), Oil Control Valve #1/#2 (Exhaust)
SENSOR3
10A
PCM, Fuel Pump Relay
IGN COIL
20A
Ignition Coil #1~#6, Condensor #1/#2
Maintenance
76
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
✽
✽
NOTICE
• If the light bulb or lamp connector
is removed from an operating
lamp activated by electricity, the
fuse box’s electronic device may
scan it as a malfunction.
Therefore, a lamp malfunction
history may be recorded in
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp
may blink temporarily. Since this
occurrence is due stabilization
function of the vehicle’s electronic
control device, if the lamp lights
up normally after temporary
blinking, there is no problem in
the vehicle.
However, if the lamp continues to
blink several times or turn off
completely, there may be an error
in the vehicle’s electronic control
device. So please have the vehicle
checked by an authorized Kia
dealer immediately.
WARNING
-
Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
CAUTION -
Light replace-
ment
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
CAUTION -
Headlamp
Lens
To prevent damage, do not clean
headlamp lens with chemical
solvents or strong detergents.
7 77
Maintenance
If you don’t have necessary tools, the
correct bulbs and the expertise, con-
sult an authorized Kia dealer. In many
cases, it is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true if you have to remove the head-
light assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
Front light bulb replacement
(1) Headlight (High)
(2) Headlight (Low)
(3) Turn signal light / Position light
(if equipped)
(4) Side marker light
(5) Front fog light (if equipped)
(6) Position light (if equipped)
(1) Headlight (High)
(2) Headlight (Low)
(3) Turn signal light
(4) Side marker light
(5) Front fog light (if equipped)
(6) Position light
OYP074016K
■
Type A
OYP074016N
■
Type B
Maintenance
78
7
Headlight bulb
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids. Never touch the glass with
bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlight.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
WARNING
- HID Headlamp
low beam (if equipped)
Do not attempt to replace or
inspect the low beam (XENON
bulb) due to electric shock dan-
ger.
If the light bulb does not oper-
ate, have your vehicle checked
by an authorized Kia dealer.
OXM079200N
WARNING
- Halogen
bulbs
Handle halogen bulbs with care.
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
7 79
Maintenance
Headlamp (bulb type) -high/low
1. Open the hood.
2. Remove the front cover(1) and
headlamp assembly nuts(2).
3. Remove the headlamp assembly
from the body of the vehicle
4. Remove the headlamp bulb cover
by turning it counterclockwise.
5. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
6. Remove the bulb by pulling it out.
7. Inset a new bulb by inserting it into
the socket.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the headlamp bulb cover by
turning it clockwise.
Turn signal lamp/Position lamp
Follow the steps 1 to 3 from the pre-
vious page.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket
OYP074056N
OYP074068N
OYP074069N
OYP074055N
High lamp
Low lamp
Maintenance
80
7
6. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
✽
✽
NOTICE
If bulb will not rotate inside socket,
remove bulb, rotate 180°, and try
again.
Front side marker
Follow the steps 1 to 3 from the pre-
vious page.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Pull the bulb out of the socket.
6. Insert a new bulb into the socket.
7. Install the socket into the assem-
bly by aligning the tabs on the
socket with the slots on the
assembly and turning the socket
clockwise.
Front fog lamp bulbs (if equipped)
OYP074057N
OYP074058N
OYP074059N
OYP074060N
■
Type A
■
Type B
7 81
Maintenance
1. Remove the front bumper under
cover.
2. Reach your hand into the back of
the front bumper.
3. Disconnect the power connector
from the socket.
4. Remove the bulb-socket from the
housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
6. Connect the power connector to
the socket.
7. Reinstall the front bumper under
cover.
✽
✽
NOTICE
Always have the headlight aiming
Adjusted after an accident or the
Headlight assembly is reinstalled at
a Authorized Kia dealer.
Headlamp (HID type), Front posi-
tion (LED), bulb replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
✽
✽
NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer
to last twice as long or longer than
halogen bulbs depending on their
frequency of use. They will probably
require replacement at some point
in the life of the vehicle. Cycling the
headlamps on and off more than
typical use will shorten HID lamps
life. HID lamps do not fail in the
same manner as halogen incandes-
cent lamps. If a headlamp goes out
after a period of operation but will
immediately relamp when the head-
lamp switch is cycled it is likely the
HID lamp needs to be replaced. HID
lamping components are more com-
plex than conventional halogen
bulbs thus have higher replacement
cost.
Maintenance
82
7
Side repeater lamp replace-
ment
If the light bulb does not
operate,have the vehicle checked by
an authorized Kia dealer. A skilled
technician should check or repair the
side repeater lamp, for it may dam-
age related out side mirror parts of
the vehicle.
Rear combination lamp bulb
replacement
(1) Stop and tail light
(2) Tail light
(3) Rear turn signal light
(4) Back-up light
(5) Rear side marker light
OYP074018K
OYP074019K
OYP074020K
■
Type A
■
Type B
7 83
Maintenance
Outside lamp
1. Open the liftgate (tailgate).
2. Loosen the lamp assembly retain-
ing screws with a philips head
screwdriver.
3. Remove the rear combination
lamp assembly from the body of
the vehicle.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
OYP074021K
OYP074022K
OYP074023K
Maintenance
84
7
7. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
* If your vehicle is equipped with LED
type stop and tail lights replace with
LED assembled units. Please con-
tact an authorized Kia dealer.
Type B (Stop and tail lamp)
If the lamp bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
Inside lamp
1. Open the liftgate (tailgate).
2. Remove the service cover.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
OYP074026K
OYP074024K
OYP074024N
■
Type A
■
Type B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст