KIA Cadenza (2019 year). Instruction — part 29
7 61
Maintenance
Fuse Name
Fuse rating
Circuit Protected
P/SEAT (DRV)
30A
Driver Seat Manual Switch, Driver Integrated memory system Module
POWER OUTLET
20A
Front Power Outlet, Rear Power Outlet
MODULE 2
10A
AMP (Amplifier), Surround View Unit, BCM (Body Control Module), Air Conditioner Control Module, Analog
Clock, Wireless Charger Unit, Air Conditioner Switch, Smart Key Control Module, Front Monitor,
Audio/Video & Navigation Head Unit, Engine Room Junction Block(Power Outlet Relay), USB Charger
SPARE
10A
Spare
MODULE 8
7.5A
BCM (Body Control Module), Smart Key Control Module
Maintenance
62
7
Engine compartment fuse panel
OYG076037N
OYG076036
7 63
Maintenance
Fuse Name
Fuse rating
Circuit Protected
MULTI
FUSE
MDPS
80A
MDPS (Motor Driven Power Steering) UNIT
B+2
60A
IGPM (Integrated Gateway Power control Module)
BLOWER
50A
Blower Relay
B+3
50A
IGPM (Integrated Gateway Power control Module)
REAR
HEATED
50A
Rear Heated Relay
ABS1
40A
ESC (Electronic Stability Control) Module
IG2
30A
Without Smart Key : Start Relay, Ignition Switch
With Smart Key : Start Relay
B+5
80A
WIPER1, HORN, ECU2, FUEL PUMP, Engine Control Relay
B+1
60A
IGPM (Integrated Gateway Power control Module)
COOLING
FAN2
60A
Cooling Fan1 Relay, Cooling Fan2 Relay
B+4
50A
IGPM (Integrated Gateway Power control Module)
POWER
OUTLET1
40A
Power Outlet Relay
IG1
40A
Without Smart Key : Ignition Switch
With Smart Key : Ignition switch 1, ACC Relay
ABS2
30A
ESC (Electronic Stability Control) Control Module, Multipurpose Check Connector
Engine room compartment fuse panel
Maintenance
64
7
Fuse Name
Fuse rating
Circuit Protected
FUSE
TCU1
15A
TCM (Transmission Control Module)
CRUISE
10A
Smart Cruise Control Unit
AMS
10A
Battery Sensor
DEICER
20A
Front Deicer Relay
A/CON
10A
Air Conditioner Control Module
WIPER2
10A
BCM (Body Control Module), ECM (Engine Control Module)
HEATED
MIRROR
10A
Air Conditioner Switch, Driver/Passenger Power Outside Mirror
ECU3
10A
ECM (Engine Control Module)
POWER
OUTLET2
20A
Front Power Outlet & Cigarette Lighter
HORN
20A
Horn Relay
WIPER1
30A
Wiper Power Relay
7 65
Maintenance
Fuse Name
Fuse rating
Circuit Protected
FUSE
TCU2
15A
TCM (Transmission Control Module), Transaxle Range Switch
ABS3
10A
ESC (Electronic Stability Control) Module
POWER
OUTLET3
20A
Not Used
B/UP LAMP
10A
Electro Chromic Mirror, Rear Combination Lamp (Inside) Left Handle side/Right Handle side
SENSOR1
15A
Oxygen Sensor #1~#4
IGN COIL
20A
Ignition Coil #1~#6
ECU2
10A
ECM (Engine Control Module)
FUEL PUMP
20A
Fuel Pump Relay
ECU1
20A
ECM (Engine Control Module)
INJECTOR
15A
Not Used
SENSOR2
10A
Variable Intake Solenoid Valve #1, #2, Electronic Thermostat, Purge Control Solenoid Valve, Canister
Close Valve, Oil Pressure Solenoid Valve, Oil Control Valve #1~#4, Cooling Fan1 Relay, Cooling Fan2
Relay, Fuel Pump Relay
Maintenance
66
7
Relay Name
Type
Blower Relay
MINI
Cooling Fan1 Relay
MINI
Cooling Fan2 Relay
MINI
Power Outlet Relay
MICRO
Start Relay
MICRO
Front Deicer Relay
MICRO
Fuel Filler Relay
MICRO
Rear Heated Relay
MINI
Relay
7 67
Maintenance
Engine compartment fuse panel
(Battery terminal cover)
✽
✽
NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle. It is accurate at the
time of printing. When you inspect
the fuse panel in your vehicle, refer
to the fuse panel label.
OYG076038
OYG076039
Maintenance
68
7
LIGHT BULBS
Bulb replacement precaution
Please keep extra bulbs on hand
with appropriate wattage ratings in
case of emergencies.
Refer to “Bulb Wattage” in chapter 8.
When changing lamps, first turn off
the engine at a safe place, firmly
apply the parking brake and detach
the battery’s negative (-) terminal.
Use only bulbs of the specified
wattage.
• Lamp part malfunction due to
net-work failure
The headlamp, taillight, and fog light
may light up when the head lamp
switch is turned ON, and not light up
when the taillight or for light switch is
turned ON. This may be cause by
network failure or vehicle electrical
control system malfunction. If there is
a problem, we recommend the sys-
tem be serviced by an authorized Kia
dealer.
• Lamp part malfunction due to elec-
trical control system stabilization
A normally functioning lamp may
flicker momentarily. This momentary
occurrence is due to the stabilization
function of the vehicle's electrical on
control system. If the lamp stops
flickering after a few moments, the
vehicle does not require service.
However, if the lamp goes out after
the momentary flickering, or the flick-
ering continues, we recommend the
system be serviced by an authorized
Kia dealer.
WARNING
- Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle, burns to your skin or fin-
gers, or an electric shock.
CAUTION -
Light replace-
ment
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
CAUTION -
Headlamp
Lens
To prevent damage, do not
clean the headlamp lens with
chemical solvents or strong
detergents.
7 69
Maintenance
✽
✽
NOTICE
• If the light bulb or lamp connector
is removed while the lamp is still
on, the fuse box's electronic sys-
tem may log it as a malfunction.
Therefore, a lamp malfunction
incident may be recorded as a
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp
to flicker momentarily. This is due
to a stabilization function of the
vehicle’s electronic control device.
If the lamp lights up normally
after momentarily blinking, then
it is functioning as normal.
However, if the lamp continues to
flicker several times or turns off
completely, there may be an error
in the vehicle’s electronic control
device. Please have the vehicle
checked by an authorized Kia
dealer immediately.
✽
✽
NOTICE
We recommend that the headlight
aiming be adjusted after an accident
or after the headlight assembly is rein-
stalled at an authorized Kia dealer.
✽
✽
NOTICE
• After driving in heavy rain or
washing, headlamp and taillamp
lenses could appear foggy. This
condition is caused by the temper-
ature difference between the lamp
inside and outside. This is similar
to the condensation on your win-
dows inside your vehicle during
the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb cir-
cuitry, we recommend that you
have the vehicle checked by an
authorized Kia dealer.
• Headlamp desiccant (if equipped)
This vehicle is equipped with des-
iccant to reduce fogging inside the
headlamp due to moisture.
The desiccant is a hygroscopic
substance and its performance
may change based on the used
period or environment.
If fogging inside the headlamp due
to moisture continues for a long
time, we recommend that you con-
sult an authorized Kia dealer.
Maintenance
70
7
If you don’t have the necessary tools,
the correct bulbs and the expertise,
consult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.
If non-genuine parts or substandard
bulbs are used, it may lead to blow-
ing a fuse or other wiring damages.
Do not install extra lamps or LEDs to
the vehicle. If additional lights are
installed, it may lead to lamp mal-
functions and flickering. Additionally,
the fuse box and other writing may
be damaged.
Light bulb position (Front)
(1) Headlamp (Low)
(2) Headlamp (High)
(3) Front turn signal lamp
(4) Day time running lamp*/
Position lamp (LED type)
(5) Front fog lamp (Bulb type)
(6) Front fog lamp (LED type)
(7) Front side marker
* : if equipped
OYG076044N
OYG076109N
■
Head lamp - Type A
■
Head lamp - Type B
OYG076045
OYG076046
■
Fog lamp - Type A
■
Fog lamp - Type B
7 71
Maintenance
Light bulb position (Rear)
(1) Stop and tail lamp (LED type)
(2) Stop and tail lamp (LED type)
(3) Rear turn signal lamp
(4) Back-up lamp
(5) High mounted stop lamp (LED
type)
(6) License plate lamp
Light bulb position (Side)
(1) Side repeater lamp (LED type)
OYG076050
OYG076047
OYG076048
OYG076049
■
Rear combination lamp
■
High mounted stop lamp
■
License plate lamp
Maintenance
72
7
Headlamp (LED type) bulb
replacement
If the head lamp (LED) (1,2) does
not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the head lamp (LED), for it
may damage related parts of the
vehicle.
Headlamp (Low beam) bulb
replacement
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.
4. Remove the bulb from bulb-socket
by pulling it out.
5. Insert a new bulb by inserting it
into the bulb-socket.
6. Install the bulb-socket in the head-
lamp assembly by aligning the
tabs on the bulb-socket with the
slots in the headlamp assembly.
Push the bulb-socket into the
headlamp assembly and turn the
bulb-socket clockwise.
7. Install the headlamp bulb cover by
turning it clockwise.
OYG076051
OYG076110N
7 73
Maintenance
Headlamp bulb
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids. Never touch the glass with
bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
Headlamp (High beam) bulb
replacement
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Disconnect the headlamp bulb
socket-connector.
4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.
WARNING
- Halogen
bulbs
Handle halogen bulbs with care.
• Halogen bulbs contain pres-
surized gas that will produce
flying pieces of glass if bro-
ken.
OHD076046
OYG076052
Maintenance
74
7
5. Install a new bulb-socket assem-
bly in the headlamp assembly by
aligning the tabs on the bulb-sock-
et with the slots in the headlamp
assembly. Push the bulb-socket
into the headlamp assembly and
turn the bulb-socket clockwise.
6. Install the headlamp bulb cover by
turning it clockwise.
Front turn signal lamp bulb
replacement
1. Open the hood.
2. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.
3. Remove the bulb from the bulb-
socket by pressing it in and rotat-
ing it counterclockwise until the
tabs on the bulb align with the
slots in the bulb-socket. Pull the
bulb out of the bulb-socket.
4. Insert a new bulb by inserting it
into the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp
assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock-
et into the headlamp assembly
and turn the socket clockwise.
OYG076053
7 75
Maintenance
Front fog lamp (LED type) bulb
replacement
If the front fog lamp (LED) (1, 2) does
not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the front fog lamp (LED), for it
may damage related parts of the
vehicle.
Position lamp + DRL* (LED
type) bulb replacement
If the position lamp + DRL* (1) does
not operate, have the vehicle
checked by an authorized Kia dealer.
OYG076054
OYG076055
■ Type A
■ Type B
OYG076056
OYG076111N
■ Type A
■ Type B
Maintenance
76
7
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the position lamp + DRL* (1),
for it may damage related parts of
the vehicle.
* : if equipped
Side repeater lamp bulb
replacement
If the Side repeater lamp does not
operate, have the vehicle checked by
an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the side repeater lamp, for it
may damage related parts of the
vehicle.
Rear turn signal lamp bulb
replacement
1. Open the trunk lid.
2. Open the service cover.
OYG076057
OYG076050
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст