KIA Cadenza (2019 year). Instruction — part 8

4 43

Features of your vehicle

If your vehicle is equipped with a
sunroof, you can slide or tilt your
sunroof with the sunroof control lever
located on the overhead console.
The sunroof can be operated for
approximately 30 seconds after the
Engine Start/Stop button is in the
OFF position.
However, if the driver’s door is
opened, the sunroof cannot be oper-
ated even within the 30 second peri-
od.

In cold and wet climates, the sunroof
may not work properly due to freez-
ing conditions.
After the vehicle is washed or in a
rainstorm, be sure to wipe off any
water that is on the sunroof before
operating it.

The sunroof cannot slide when it is in
the tilt position nor can it be tilted
while in an open or slide position.

PANORAMIC SUNROOF (IF EQUIPPED)

CAUTION

-

Sunroof
control lever

Do not continue to press the sun-
roof control lever after the sun-
roof is fully opened, closed, or
tilted. Damage to the motor or
system components could occur.

CAUTION -

Sunroof motor
damage

To prevent damage to the sun-
roof, periodically remove any
dirt that may accumulate on the
guide rail.

WARNING

- Roof cargo

Do not operate the sun roof
while using the roof rack to
transport cargo. This may cause
the cargo to come loose and
distract the driver.

OYG046035

WARNING

Do not allow children to operate
the sunroof. This may result in
injury to the child.

WARNING

Never adjust the sunroof or
sunshade while driving. This
could result in loss of control
and an accident that may cause
death, serious injury, or proper-
ty damage.

Features of your vehicle

44

4

Sunroof open warning
(if equipped)

If the driver turns off the engine when
the sunroof is not fully closed, the
warning chime will sound for a few
seconds and the above warning illus-
tration will appear on the LCD display
or the warning indicator will illumi-
nate.
Close the sunroof securely when
leaving your vehicle.

CAUTION

Do not extend any luggage out-
side the sunroof while driving.

OYG046145

CAUTION

Make sure the sunroof is fully
closed when leaving your vehi-
cle. If the sunroof is open, rain or
snow may leak through the sun-
roof and wet the interior as allow
theft to occur.

WARNING

In order to prevent accidental
operation of the sunroof, espe-
cially by a child, do not let a
child operate the sunroof.

WARNING

Do not sit on the top of the vehi-
cle. It may cause vehicle dam-
age.

4 45

Features of your vehicle

Sunshade

To open the sunshade

Push the sunroof control lever back-
ward to the 1st detent position.

To close the sunshade when the
sunroof glass is closed

Push the sunroof control lever for-
ward to the 1st detent position.
To stop the sliding at any point, press
the sunshade control switch momen-
tarily.

✽

✽

NOTICE

Wrinkles formed on the sunshade as
material characteristic are normal.

✽

✽

NOTICE

Only the front glass of the panora-
ma sunroof opens and closes.

Sliding the sunroof

When the sunshade is closed

Push the sunroof control lever back-
ward to the 2nd detent position and
both the sunshade and sunroof glass
will slide all the way open. To stop the
sunroof movement at any point, push
the sunroof control glass lever
momentarily.

CAUTION

- Automatic

sunroof shade

• Do not pull or push the sun-

shade by hand as such action
may damage the sunshade or
cause it to malfunction.

• Close the sunroof when driv-

ing in dusty environments.
Dust may cause a malfunction
of the vehicle system.

OYG046452L

OYG046036

Features of your vehicle

46

4

When the sunshade is opened

If you push the sunroof control lever
backward, the sunroof glass will slide
all the way open. To stop the sunroof
movement at any point, push the sun-
roof control lever momentarily.

Automatic reversal

If an object or part of the body is
detected while the sunroof is closing
automatically, it will reverse the direc-
tion, and then stop.
The auto reverse function may not
work if a tiny obstacle is obstacle is
lodged between the sliding glass and
the sunroof sash. You should always
check that all passengers and
objects are away from the sunroof
before closing it.

Objects less than 0.16 inch (4 mm) in
diameter caught between the sun-
roof glass and the front glass chan-
nel may not be detected by the auto-
matic reverse glass and the glass will
not stop and reverse direction.

OXM049029

WARNING

- Sunroof

Operation

When closing the sunroof, make
sure there are no body parts in
the movement range of the slid-
ing roof. Parts of the body could
become trapped or crushed.

WARNING

- Sunroof

• Be careful that no head, hands

and body parts are obstructed
by a closing sunroof.

• Do not extend the face, neck,

arms or body outside the sun-
roof while driving.

4 47

Features of your vehicle

✽

✽

NOTICE

If you drive with the sunroof opened
right after a vehicle wash or rain,
water may get inside the vehicle.

Tilting the sunroof

When the sunshade is closed

Push the sunroof control lever upward,
the sunshade will slide all the way
open then the sunroof glass will tilt.
To stop the sunroof movement at any
point, push the sunroof control lever
momentarily.

When the sunshade is opened

Push the sunroof control lever
upward, the sunroof glass will tilt.
To stop the sunroof movement at any
point, push the sunroof control lever
momentarily.

Closing the sunroof

To close the sunroof glass with
the sunshade

Push the sunroof control lever for-
ward to the first detent position.

To close the sunroof glass only

Push the sunroof control lever for-
ward to the second detent position.
The sunroof glass will close then the
sunshade close automatically.
To stop the sunroof movement at any
point, push the sunroof control lever
momentarily.

CAUTION

To prevent damage to the sun-
roof, periodically remove any
dirt that may accumulate on the
guide rail.

CAUTION

- Sunroof motor

damage

If you try to open the sunroof
when the temperature is below
freezing or when the sunroof is
covered with snow or ice, the
glass or the motor could be
damaged.

OYG046037

Features of your vehicle

48

4

Resetting the sunroof

Whenever the vehicle battery is dis-
connected or discharged, you must
reset your sunroof system as follows:
1.Start the engine.
2.Close the sunshade and sunroof

completely if opened.

3.Release the sunroof control lever.
4.Push the sunroof control lever for-

ward in the direction of close
(about 10 seconds) until the sun-
shade slightly moves.

Then,

release the lever.

5.Push the sunroof control lever for-

ward in the direction of close, until
the sunroof operates as follows
again:

Sunshade Open

→ Glass Tilt Open

→ Glass Tilt Close → Glass Slide

Open

→ Glass Slide Close →

Sunshade Close

Then, release the lever.

When this is complete, the sunroof
system has been reset and one
touch open and close should be
restored.

✽

✽

NOTICE

If the Resetting the Sunroof proce-
dure is not correctly followed, the
sunroof may not operate properly.

4 49

Features of your vehicle

Electric power steering (EPS)

The power steering uses a motor to
assist you in steering the vehicle. If
the engine is off or if the power steer-
ing system becomes inoperative, the
vehicle may still be steered, but it will
require increased steering effort.
The motor driven power steering is
controlled by a power steering con-
trol unit which senses the steering
wheel torque and vehicle speed to
command the motor.
The steering becomes heavier as the
vehicle’s speed increases and
becomes lighter as the vehicle’s
speed decreases for optimum steer-
ing control.
Should you notice any change in the
effort required to steer during normal
vehicle operation, have the power
steering checked by an authorized
Kia dealer.

• When you operate the steering

wheel in low temperature, noise
may occur. If temperature rises, the
noise will likely disappear. This is a
normal condition.

• When the vehicle is stationary, and

the steering wheel is turned all the
way to the left or right continuous-
ly, the steering wheel becomes
harder to turn. The power assist is
limited to protect the motor from
overheating.
As time passes, the steering wheel
will return to its normal condition.

✽

✽

NOTICE

The following symptoms may occur
during normal vehicle operation:
• The EPS warning light does not

illuminate.

• The steering gets heavy immedi-

ately after turning the ignition
switch on. This happens as the sys-
tem performs the EPS system
diagnostics. When the diagnostics
are completed, the steering wheel
will return to its normal condition.

• A click noise may be heard from

the EPS relay after the Engine
Start/Stop button is turned to the
ON or OFF position.

• A motor noise may be heard when

the vehicle is at a stop or at a low
driving speed.

• If the Electric Power Steering

System does not operate normally,
the warning light will illuminate on
the instrument cluster. The power
steering system will not operate
and steering effort can increase.
Take your vehicle to an authorized
Kia dealer and have the vehicle
checked as soon as possible.

(Continued)

STEERING WHEEL

Features of your vehicle

50

4

(Continued)
• When the charging system warning

light comes on due to low voltage
(When should be lower case the
alternator or battery do not oper-
ate normally or malfunction), the
steering wheel may require
increased steering effort.

Tilt and telescopic steering

Tilt and telescopic steering allows
you to adjust the steering wheel
before you drive. You can also raise it
to give your legs more room when
you exit and enter the vehicle.

The steering wheel should be posi-
tioned so that it is comfortable for
you to drive, while permitting you to
see the instrument panel warning
lights and gauges.

Manual type

To change the steering wheel angle,
pull down the lock-release lever (1),
adjust the steering wheel to the
desired angle (2) and height (3) then
pull up the lock-release lever to lock
(4) the steering wheel in place. Be
sure to adjust the steering wheel to
the desired position before driving.

▼

WARNING

- Steering

wheel adjustment

Never adjust the angle and
height of the steering wheel
while driving. You may lose
steering control.

OYG046038

4 51

Features of your vehicle

✽

✽

NOTICE

After adjustment, sometimes the
lock release lever may not lock the
steering wheel. It is not a malfunc-
tion. This occurs when two gears are
not engaged correctly. In this case,
adjust the steering wheel again and
then lock the steering wheel.

Electric type

Adjust the steering wheel angle (2)
and position (3) with the knob (1) on
the steering column. Move the steer-
ing wheel, so it points toward your
chest, not toward your face. Make
sure you can see the instrument
panel warning lights and gauges.
After adjusting, push the steering
wheel both up and down to be cer-
tain it is locked in position. Always
adjust the position of the steering
wheel before driving.

✽

✽

NOTICE

To prevent discharge of the battery,
do not operate when the engine is
stopped.

▼

OYG046039

Features of your vehicle

52

4

Heated steering wheel
(if equipped)

With the Engine Start/Stop Button in
the ON position, pressing the heat-
ed steering wheel button warms the
steering wheel. The indicator on the
button will illuminate.
To turn the heated steering wheel off,
press the button once again. The
indicator on the button will turn off.

✽

✽

NOTICE

The heated steering wheel will turn
off automatically approximately 30
minutes after the heated steering
wheel is turned on.

OYG046040

CAUTION

• Do not install any type of grip

cover for the steering wheel, it
may impair the function of the
heated steering wheel system.

• When cleaning the heated

steering wheel, do not use an
organic solvent such as paint
thinner, benzene, alcohol and
gasoline. Doing so may dam-
age the surface of the steering
wheel.

• If the surface of steering

wheel is damaged by a sharp
object, damage to the heated
steering wheel components
could occur.

WARNING

If the steering wheel becomes
too warm, turn the system off.
The heated steering wheel may
cause burns even at low tem-
peratures, especially if used for
long periods of time.

4 53

Features of your vehicle

Horn

To sound the horn, press the horn
symbols on your steering wheel.
Check the horn regularly to be sure it
operates properly.

✽

✽

NOTICE

To sound the horn, press the area
indicated by the horn symbol on
your steering wheel (see illustra-
tion). The horn will operate only
when this area is pressed.

OYG046041

Features of your vehicle

54

4

MIRRORS

Inside rearview mirror

Adjust the rearview mirror so that the
center view through the rear window
is seen. Make this adjustment before
you start driving.
Do not place objects in the rear seat
or cargo area which would interfere
with your vision through the rear win-
dow.

Day/night rearview mirror
(if equipped)

Make this adjustment before you
start driving and while the day/night
lever (3) is in the day position.
Pull the day/night lever (3) toward
you to reduce the glare from the
headlights of the vehicles behind you
during night driving.
Remember that you lose some
rearview clarity in the night position.

❈ (1) : Day, (2) : Night

WARNING

- Mirror adjust-

ment

Do not adjust the rearview mir-
ror while the vehicle is moving.
This could result in loss of con-
trol.

WARNING

Do not modify the inside mirror
and don’t install a wide mirror. It
could result in injury during an
accident or deployment of the
air bag.

OYG046054L

4 55

Features of your vehicle

Electrochromic mirror with
HomeLink system (if equipped)

To operate the electric rearview mirror
Press the I button (1) to turn the
automatic- dimming function on. The
mirror indicator light will illuminate.
Press the O button (2) to turn the
automatic- dimming function off. The
mirror indicator light will turn off.

HomeLink

®

Wireless Control System

Your new mirror comes with an inte-
grated HomeLink Universal
Transceiver, which allows you to pro-
gram the mirror to activate your
garage door(s), estate gate, home
lighting, etc. The mirror actually
learns the codes from your various
existing transmitters.
Retain the original transmitter for
future programming procedures (i.e.,
new vehicle purchase). It is also sug-
gested that upon the sale of the vehi-
cle, the programmed HomeLink but-
tons be erased for security purposes
(follow step 1 in the “Programming”
portion of this text).

Programming

Your vehicle may require the ignition
switch to be turned to the ACC posi-
tion for programming and/or opera-
tion of HomeLink. It is also recom-
mended that a new battery be
replaced in the hand-held transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the radio-
frequency.
Follow these steps to train your
HomeLink mirror:

OHD046025N

OHD046305N

Glare detection sensor

Indicator light

Homelink buttons

Features of your vehicle

56

4

1. When programming the buttons for

the first time, press and hold the
left and center buttons (

,

)

simultaneously until the indicator
light begins to flash after approxi-
mately 20 seconds. (This proce-
dure erases the factory-set default
codes. Do not perform this step
when programming the additional
HomeLink buttons.)

✽

✽

NOTICE

For non rolling code garage door
openers, follow steps 2 - 3.
For rolling code garage door open-
ers, follow steps 2 - 6.
For Canadian Programming, please
follow the Canadian Programming
section.
For help with determining whether
your garage door opener is non-
rolling code or rolling code, please
refer to the garage door openers
owner’s manual or

contact

HomeLink customer service at 1-
800-355-3515.

2. Press and hold the button on the

HomeLink system you wish to
train and the button on the trans-
mitter while the transmitter is
approximately 2-8 cm (1 to 3 inch-
es) away from the mirror. Do not
release the buttons until step 3
has been completed.

3. The HomeLink indicator light will

flash, first slowly and then rapidly.
When the indicator light flashes
rapidly, both buttons may be
released. (The rapid flashing light
indicates successful programming
of the new frequency signal.)

OHD046306N

Flashing

OHD046307N

Flashing

1-3inches

Transmitter

4 57

Features of your vehicle

✽

✽

NOTICE

Some gate and garage door openers
may require you to replace step #3
with the “cycling” procedure noted
in the “Canadian Programming”
section of this document.

Rolling code programming

To train a garage door opener (or other
rolling code equipped devices) with the
rolling code feature, follow these
instructions after completing the
“Programming” portion of this text. (A
second person may make the following
training procedures quicker & easier.)
4. Locate the “learn” or “smart” but-

ton on the device’s motor head
unit. Exact location and color of
the button may vary by product
brand. If there is difficulty locating
the “learn” or “smart” button, refer-
ence the device’s owner’s manual
or contact HomeLink at 1-800-
355-3515 or on the internet at
www.homelink.com.

5. Press and release the “learn” or

“smart” button on the device’s
motor head unit. You have 30 sec-
onds to complete step number 6.

6. Return to the vehicle and firmly

press and release the pro-
grammed HomeLink button up to
three times. The rolling code
equipped device should now rec-
ognize the HomeLink signal and
activate when the HomeLink but-
ton is pressed. The remaining two
buttons may now be programmed
if this has not previously been
done. Refer to the “Programming”
portion of this text.

Features of your vehicle

58

4

Operating HomeLink

To operate, simply press the pro-
grammed HomeLink button.
Activation will now occur for the
trained product (garage door, securi-
ty system, entry door lock, estate
gate, or home or office lighting). For
convenience, the hand-held trans-
mitter of the device may also be used
at any time. The HomeLink Wireless
Controls System (once programmed)
or the original hand-held transmitter
may be used to activate the device
(e.g. garage door, entry door lock,
etc.). In the event that there are still
programming difficulties, contact
HomeLink at 1-800-355-3515 or on
the internet at www.homelink.com.

Erasing programmed
HomeLink buttons

To erase the three programmed but-
tons (individual buttons cannot be
erased):
• Press and hold the left and center

buttons simultaneously, until the
indicator light begins to flash
(approximately 20 seconds).
Release both buttons. Do not hold
for longer than 30 seconds.

HomeLink is now in the train (or
learning) mode and can be pro-
grammed at any time.

Reprogramming a single
HomeLink button

To program a device to HomeLink
using a HomeLink button previously
trained, follow these steps:
1. Press and hold the desired

HomeLink button. Do NOT release
until step 4 has been completed.

2. When the indicator light begins to

flash slowly (after 20 seconds),
position the hand-held transmitter
2-8 cm (1 to 3 inches) away from
the HomeLink surface.

3. Press and hold the hand-held

transmitter button (or press and
“cycle” - as described in “Canadian
Programming”).

4. The HomeLink indicator light will

flash, first slowly and then rapidly.
When the indicator light begins to
flash rapidly, release both buttons.

OHD046306N

Flashing