Kia Stonic (2018 year). Instruction — part 11
(Continued)
age to system parts could occur and
may not be covered by your vehicle
warranty.
When starting the vehicle in winter,
set the wiper switch in the off posi‐
tion. Otherwise, wipers may operate
and ice may damage the windshield
wiper blades. Always remove all
snow and ice and defrost the wind‐
shield properly prior to operating the
windshield wipers.
Windshield washers (front)
In the O (Off) position, pull the lever
gently toward you to spray washer flu‐
id on the windshield and to run the wip‐
ers 1-3 cycles.
Use this function when the windshield
is dirty.
The spray and wiper operation will con‐
tinue until you release the lever.
If the washer does not work, check the
washer fluid level. If the fluid level is
not sufficient, you will need to add ap‐
propriate
non-abrasive
windshield
washer fluid to the washer reservoir.
The reservoir filler neck is located in
the front of the engine compartment
on the passenger side.
CAUTION
To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
WARNING
Do not use the washer in freezing
temperatures without first warming
the windshield with the defrosters;
the washer solution could freeze on
the windshield and obscure your vi‐
sion.
CAUTION
• To prevent possible damage to the
wipers or windshield, do not oper‐
ate the wipers when the wind‐
shield is dry.
• To prevent damage to the wiper
blades, do not use gasoline, kero‐
sene, paint thinner, or other sol‐
vents on or near them.
(Continued)
Features of your vehicle
4-92
(Continued)
• To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
• To prevent possible damage to the
wipers and washer system, use
anti-freezing washer fluids in the
winter season or cold weather.
Rear window wiper and washer
switch (if equipped)
The rear window wiper and washer
switch is located at the end of the wip‐
er and washer switch lever. Turn the
switch to desired position to operate
the rear wiper and washer.
6. 2 - Normal wiper operation
7. 1/ON - Intermittent wipe
8. O - Wiper is not in operation
■ Type A
■ Type B
4-93
4
Featur
es of your v
ehicle
Push the lever away from you or turn
the wiper lever switch upwards twice
to spray rear washer fluid and to run
the rear wipers 1~3 cycles. The spray
and wiper operation will continue until
you release the lever.
Features of your vehicle
4-94
INTERIOR LIGHT
CAUTION
Do not use the interior lights for ex‐
tended periods when the engine is
not running.
It may cause battery discharge.
WARNING
Do not use the interior lights when
driving in the dark. Accidents could
happen because the view may be
obscured by interior lights.
Map lamp
■ Type A
■ Type B
• (1) : Press the lamps to turn the
front map lamps on and off.
•
(2):
- The map lamp and room lamp
comes on when a door is opened.
The lamps go out after approxi‐
mately 30 seconds.
- The map lamp and room lamp
comes on for approximately 30
seconds when doors are unlocked
with a transmitter or smart key as
long as the doors are not opened.
- The map lamp and room lamp will
stay on for approximately 20 mi‐
nutes if a door is opened with the
ignition switch in the ACC or
LOCK/OFF position.
- The map lamp and room lamp will
stay on continuously if the door is
opened with the ignition switch in
the ON position.
- The map lamp and room lamp will
go out immediately if the ignition
switch is changed to the ON posi‐
tion or all doors are locked.
- To turn off the DOOR mode, press
the DOOR button (2) once again
(not pressed).
4-95
4
Featur
es of your v
ehicle
NOTICE
The DOOR mode and ROOM mode
can not be selected at a time.
Front Map Lamp:
• Type A
(3): Press this switch to turn the
front map lamps on.
(4): Press this switch to turn the
front map lamps off.
• Type B
(3): Press this switch to turn the
front map lamps on and off.
Room lamp
•
: The light stays on at all times.
Luggage room lamp (if
equipped)
The luggage room lamp comes on when
the trunk (tailgate) is opened.
CAUTION
The luggage room lamp comes on as
long as the trunk (tailgate) opens. To
prevent unnecessary charging sys‐
tem drain, close the trunk (tailgate)
(Continued)
(Continued)
securely after using the luggage
room.
Vanity mirror lamp (if equipped)
Push the switch to turn the light on or
off.
: The lamp will turn on if this but‐
ton is pressed.
: The lamp will turn off if this button
is pressed.
Features of your vehicle
4-96
CAUTION
n Vanity mirror lamp
Always have the switch in the off
position when the vanity mirror
lamp is not in use. If the sunvisor is
closed without the lamp off, it may
discharge the battery or damage the
sunvisor.
Glove box lamp (if equipped)
The glove box lamp comes on when the
glove box is opened.
CAUTION
To prevent unnecessary charging
system drain, close the glove box se‐
curely after using the glove box.
4-97
4
Featur
es of your v
ehicle
DEFROSTER
CAUTION
To prevent damage to the conduc‐
tors bonded to the inside surface of
the rear window, never use sharp in‐
struments or window cleaners con‐
taining abrasives to clean the win‐
dow.
NOTICE
If you want to defrost and defog the
front windshield, refer to Wind‐
shield defrosting and defogging on
Rear window defroster
The defroster heats the window to re‐
move frost, fog and thin ice from the
rear window, while the engine is run‐
ning.
To activate the rear window defroster,
press the rear window defroster but‐
ton.
The indicator on the rear window de‐
froster button illuminates when the de‐
froster is ON.
If there is heavy accumulation of snow
on the rear window, brush it off before
operating the rear defroster.
The rear window defroster automati‐
cally turns off after approximately 20
minutes or when the ignition switch is
turned off. To turn off the defroster,
press the rear window defroster button
again.
Outside rearview mirror defroster
(if equipped)
If your vehicle is equipped with the out‐
side rearview mirror defrosters, they
will operate at the same time you turn
on the rear window defroster
Features of your vehicle
4-98
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
1. Fan speed control knob
2. Mode selection knob
3. Temperature control knob
4. Air conditioning button (if equipped)
5. Rear window defroster button
6. Air intake control button
CAUTION
Operating the blower when the igni‐
tion switch is in the ON position
could cause the battery to discharge.
Operate the blower when the engine
is running.
4-99
4
Featur
es of your v
ehicle
Heating and air conditioning
1. Start the engine.
2. Set the mode to the desired posi‐
tion.
For improving the effectiveness of
heating and cooling;
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the
outside (fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn
the air conditioning (if equipped)
system on.
Features of your vehicle
4-100
Mode selection
The mode selection knob controls the
direction of the air flow through the
ventilation system.
Air can be directed to the floor, dash‐
board outlets, or windshield. Five sym‐
bols are used to represent Face, Bi-Lev‐
el, Floor, Floor-Defrost and Defrost air
position.
Face-Level (B, D)
Air flow is directed toward the upper
body and face. Additionally, each outlet
can be controlled to direct the air dis‐
charged from the outlet.
Bi-Level (B, D, C, E)
Air flow is directed towards the face
and the floor.
Floor-Level (C, E, A, D)
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windshield and
side window defrosters.
Floor/Defrost-Level (A, C, D,
E)
Most of the air flow is directed to the
floor and the windshield with a small
amount directed to the side window
defrosters.
Defrost-Level (A, D)
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
Instrument panel vents
OYB047304
The outlet vents can be opened or
closed separately using the thumb‐
wheel. To close the vent, rotate it
downward to the maximum position.
Also, you can adjust the direction of air
delivery from these vents using the
vent control lever as shown.
4-101
4
Featur
es of your v
ehicle
Temperature control
The temperature control knob allows
you to control the temperature of the
air flowing from the ventilation system.
To change the air temperature in the
passenger compartment, turn the knob
to the right position for warm and hot
air or left position for cooler air.
Air intake control
The air intake control is used to select
the outside (fresh) air position or recir‐
culated air position.
To change the air intake control posi‐
tion, press the control button.
Recirculated air position
With the recirculated air
position selected, air
from the passenger
compartment will be
drawn through the heat‐
ing system and heated
or cooled according to
the function selected.
Outside (fresh) air position
With the outside (fresh)
air position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.
NOTICE
Prolonged operation of the heater in
the recirculated air position (without
air conditioning selected) may cause
fogging of the windshield and side
windows and the air within the pas‐
senger compartment may become
stale.
In addition, prolonged use of the air
conditioning with the recirculated air
position selected will result in exces‐
sively dry air in the passenger com‐
partment.
Features of your vehicle
4-102
WARNING
• Continue using the climate control
system in the recirculated air posi‐
tion may allow humidity to in‐
crease inside the vehicle which
may fog the glass and obscure vis‐
ibility.
• Do not sleep in a vehicle with the
air conditioning or heating system
on. It may cause serious harm or
death due to a drop in the oxygen
level and/or body temperature.
• Continue using the climate control
system in the recirculated air posi‐
tion can cause drowsiness or
sleepiness, and loss of vehicle con‐
trol. Set the air intake control to
the outside (fresh) air position as
much as possible while driving.
Fan speed control
The ignition switch must be in the ON
position for fan operation.
The fan speed control knob allows you
to control the fan speed of the air flow‐
ing from the ventilation system. To
change the fan speed, turn the knob to
the right for higher speed or left for
lower speed.
Setting the fan speed control knob to
the 0 position turns off the fan.
To turn off the blowers
To turn off the blowers, turn the fan
speed control knob to the 0 position.
4-103
4
Featur
es of your v
ehicle
Air conditioning (A/C)
Press the A/C button to turn the air
conditioning system on (indicator light
will illuminate). Press the button again
to turn the air conditioning system off.
System operation
Ventilation
1. Set the mode to the
position.
2. Set the air intake control to the
outside (fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Set the mode to the
position.
2. Set the air intake control to the
outside (fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If dehumidified heating is desired,
turn the air conditioning system (if
equipped) on.
• If the windshield fogs up, set the
mode to the
or
position.
Operation Tips
• To keep dust or unpleasant fumes
from entering the vehicle through the
ventilation system, temporarily set
the air intake control to the recircula‐
ted air position. Be sure to return the
control to the fresh air position when
the irritation has passed to keep
fresh air in the vehicle. This will help
the driver to stay alert and comfort‐
able.
• Air for the heating/cooling system is
drawn in through the grilles just
ahead of the windshield. Care should
be taken that these are not blocked
by leaves, snow, ice or other obstruc‐
tions.
• To prevent interior fog on the wind‐
shield, set the air intake control to
the fresh air position and fan speed
to the desired position, turn on the
air conditioning system, and adjust
the temperature control to the de‐
sired temperature.
Air conditioning
Kia Air Conditioning Systems are filled
with environmentally friendly refriger‐
ant
*
.
1. Start the engine. Push the air con‐
ditioning button.
2. Set the mode to the
position.
*
Your vehicle is filled with R-134a or
R-1234yf according to the regula‐
tion in your country at the time of
producing. You can find out which air
conditioning refrigerant is applied
your vehicle at the label inside of en‐
gine room. Refer to Refrigerant la‐
bel on page 9-22 for more detail
location of air conditioning refriger‐
ant label.
Features of your vehicle
4-104
3. Set the air intake control to the
outside air or recirculated air posi‐
tion.
4. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
CAUTION
• The refrigerant system should on‐
ly be serviced by trained and certi‐
fied technicians to insure proper
and safe operation.
• The refrigerant system should be
serviced in a well-ventilated place.
• The air conditioning evaporator
(cooling coil) shall never be re‐
paired or replaced with one re‐
moved from a used or salvaged
vehicle and new replacement MAC
evaporators shall be certified (and
labeled) as meeting SAE Standard
J2842.
NOTICE
• When using the air conditioning
system, monitor the temperature
gauge closely while driving up hills
or in heavy traffic when outside
temperatures are high. Air condi‐
tioning system operation may
cause engine overheating. Contin‐
ue to use the blower fan but turn
the air conditioning system off if
the temperature gauge indicates
engine overheating.
• When opening the windows in hu‐
mid weather air conditioning may
create water droplets inside the
vehicle. Since excessive water
droplets may cause damage to
electrical equipment, air condition‐
ing should only be used with the
windows closed.
Air conditioning system operation tips
• If the vehicle has been parked in di‐
rect sunlight during hot weather,
open the windows for a short time to
let the hot air inside the vehicle es‐
cape.
• To help reduce moisture inside of the
windows on rainy or humid days, de‐
crease the humidity inside the vehicle
by operating the air conditioning sys‐
tem.
• During air conditioning system opera‐
tion, you may occasionally notice a
slight change in engine speed as the
air conditioning compressor cycles.
This is a normal system operation
characteristic.
• Use the air conditioning system every
month only for a few minutes to en‐
sure maximum system performance.
• When using the air conditioning sys‐
tem, you may notice clear water
dripping (or even puddling) on the
ground under the passenger side of
the vehicle. This is a normal system
operation characteristic.
• Operating the air conditioning system
in the recirculated air position pro‐
vides maximum cooling, however,
continual operation in this mode may
cause the air inside the vehicle to be‐
come stale.
• During cooling operation, you may oc‐
casionally notice a misty air flow be‐
cause of rapid cooling and humid air
intake. This is a normal system oper‐
ation characteristic.
4-105
4
Featur
es of your v
ehicle
Climate control air filter (if
equipped)
A : Outside air
B : Recirculated air
C : Climate control air filter
D : Blower
E : Evaporator core
F : Heater core
The climate control air filter installed
behind the glove box filters the dust or
other pollutants that come into the ve‐
hicle from the outside through the
heating and air conditioning system.
If dust or other pollutants accumulate
in the filter over a period of time, the
air flow from the air vents may de‐
crease, resulting in moisture accumula‐
tion on the inside of the windshield
even when the outside (fresh) air posi‐
tion is selected. If this happens, have
the climate control air filter replaced by
a professional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
NOTICE
• Replace the filter according to the
Maintenance Schedule.
If the vehicle is being driven in se‐
vere conditions such as dusty or
rough roads, more frequent air
conditioner filter inspections and
changes are required.
• When the air flow rate suddenly
decreases, have the system
checked by a professional work‐
shop. Kia recommends to visit an
authorized Kia dealer/service part‐
ner.
Air Conditioning refrigerant label
■ Example
Type A
Type B
❈
The actual Air Conditioning refriger‐
ant label in the vehicle may differ
from the illustration.
Features of your vehicle
4-106
Each symbols and specification on air
conditioning refrigerant label means as
below ;
1. Classification of refrigerant
2. Amount of refrigerant
3. Classification of Compressor lubri‐
cant
You can find out which air conditioning
refrigerant is applied your vehicle at
the label inside of the engine room.
Refer to Refrigerant label on page
9-22 for more detailed location of the
air conditioning refrigerant label.
Checking the amount of air
conditioner refrigerant and
compressor lubricant
When the amount of refrigerant is low,
the performance of the air conditioning
is reduced. Overfilling also has a bad in‐
fluence on the air conditioning system.
Therefore, if abnormal operation is
found, have the system inspected by a
professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
WARNING
n Vehicles
equipped
with
R-134a
*
Because the refrigerant is
at very high pressure, the
air conditioning system
should only be serviced
by trained and certified
technicians.
It is important that the correct type
and amount of oil and refrigerant is
used.
Otherwise, it may cause damage to
the vehicle and personal injury.
*
Your vehicle is filled with R-134a or
R-1234yf according to the regula‐
tion in your country at the time of
producing. You can find out which air
conditioning refrigerant is applied
your vehicle at the label inside of en‐
gine room. Refer to Refrigerant la‐
bel on page 9-22 for more detail
location of air conditioning refriger‐
ant label.
WARNING
n Vehicles
equipped
with
R-1234yf
*
Because the refrigerant is
mildly inflammable and at
very high pressure, the
air conditioning system
should only be serviced
by trained and certified
technicians.
It is important that the correct type
and amount of oil and refrigerant is
used.
Otherwise, it may cause damage to
the vehicle and personal injury.
*
Your vehicle is filled with R-134a or
R-1234yf according to the regula‐
tion in your country at the time of
producing. You can find out which air
conditioning refrigerant is applied
your vehicle at the label inside of en‐
gine room. Refer to Refrigerant la‐
bel on page 9-22 for more detail
location of air conditioning refriger‐
ant label.
4-107
4
Featur
es of your v
ehicle
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст