Geely FC. Manual part — 50
Geely FC. Manual part - 50
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Align the mark
(b) Align the mark on sliding yoke and middle shaft.
(c) Assemble B bolt and tighten A bolt.
Torque: 35 ± 3 N
xm
Hint: When changing new sliding yoke, it is neces-
sary to adjust the front wheel at the front, and
make the bolt hole surface of sliding yoke face
the back (liking that shown in figure), then as-
semble the bolt.
21. Adjust front wheel at the front.
22. Assemble helix cable assembly (equipping with
SRS) [67000121]
23. Put the helix cable assembly at central position
(equipping with SRS)
(a) Check whether the front wheel faces the front.
(b) Turn helix cable counter-clockwise with hand until it could
not turn.
(c) Then turn helix cable 2.5 clockwise and align the mark.
Hint: helix cable could turn left or right from central
position for 2.5 rounds.
24.
Assemble steering wheel assembly [67010001]
(a) Align the mark on steering wheel and main shaft assembly.
(b) Assemble the fixed screw cap of steering wheel.
(c) Connect the joint.
25. Assemble safety airbag assembly at the side of driver [67010011]
Warning:
z Forbid using SRS parts on other automobiles, when changing any part, it is necessary to use new
product.
z If safety airbag assembly at the side of driver once dropped or exterior shell and joint has crack,
concave or other distortions, it is necessary to change with new product.
z When assembling the airbag assemble at the side of driver, it is necessary to pay attention to airbag
wiring harness could not interrupt other parts or be clamped by other parts.
(a) Connect the end.
(b) Connect the joint of airbag.
(c) After assembling the safety airbag assembly at the side
of driver, insure planetary screw of concave slot contacts
with screw shell.
(d) Use planetary screwdriver to tighten two screws.
Torque: 8.8 N
xm
26. Check the central point of steering wheel
27. Check SRS warning light (equipping with SRS)
Align the
mark
197
planetary
screws
screw shell
Power steering--Poser steering system
Power steering
Power steering system
Note
1. Notes for steering system:
It is necessary to change parts correctly, for they will influence the performance of steering system to incur
running danger.
2. Notes for SRS airbag system
MR7180 equips with SRS (auxiliary protection system), such as safety airbag at the side of driver and
safety airbag at the side of passenger, if repairment does not accord with correct sequence, it might incur
SRS explodes suddenly in repairing term to make heavy accident. Before repairing (including disassem-
bling or assembling, checking or changing parts), it is necessary to read the notes in chapter SRS (auxiliary
protection system) carefully.
198
Power steering--Poser steering system
Malfunction phenomenon
Possible malfunction part
Reference page
1.
Tyre (tyre pressure is wrong).
109
2.
Power steering oil level (low).
200
3.
Driving belt (loose).
-
4.
Wheel alignment(wrong).
87
Steering is heavy
5.
Steering system joint (abraded).
-
6.
Lower control arm ball head (abraded).
99
7.
Steering column (bent).
-
8.
Power steering oil pump
203
9.
Power steering gear
205
1.
Tyre (tyre pressure is wrong).
109
Return is bad
2.
Wheel alignment (wrong)
87
3.
Steering column (bent)
-
4.
Power steering gear
205
1.
Steering system joint (abraded)
-
2.
Lower control arm ball head (abraded)
99
Clearance is too big
3.
Middle shaft, sliding fork (abraded)
-
4.
Front wheel bearing (abraded)
123
5.
Power steering gear
205
1.
Power steering oil level (low)
200
Abnormal noise
2.
Power steering joint (abraded)
-
3.
Power steering oil pump
203
4.
Power steering gear
205
Malfunction phenomenon table
Use following table to help you find the reason of malfunction, the number in table only show the possible
preference sequence of malfunction, please check each part by sequence, if necessary, change this part.
199
Power steering--Poser steering system
Inspection on automobile
1. Check driving belt
(a) Check whether the belt has been abraded too much with eyes, and rope is broken.
If finding any defect, change the driving belt.
Hint: Some light crack at the side of belt rib could be approved, but if belt has any crack from
its rib, it is necessary to change.
2. Exhaust air of power steering system
(a) Check the oil level.
(b) Lift up automobile body, and support it with bracket.
(c) Turn steering wheel.
(1) Turn steering wheel slowly from left and right to bottom for several times when engine extinguishes.
(d) Lay down the automobile.
(e) Start the engine to make it run at idling speed for several minutes.
(f) Rotate steering wheel.
(1) Keep engine at idling speed, and turn the steering wheel from left or right to bottom and keep this
state for 2-3 seconds, then turn it to the other direction for 2-3 seconds.
(2) Repeat (1) for several times.
(g) Engine extinguishes.
(h) Check whether there is any foam or emulsification
phenomenon.
If there is any foam or emulsification phenomenon and
it is necessary to exhaust air second time, it is necessary
to check whether the system has any leakage.
(i) Check the oil level.
3. Check the oil level
(a) Keep automobile horizontal.
(b) Extinguish the engine, and check the oil level of oil stor-
age tank.
If oil level is too low, add oil.
Power steering oil: automatic transmission oil
DEXRON’’ II or III
Hint: check whether the oil level is in the HOT mark
scope of oil storage tank, if oil is cool, check the
oil level is in COLD mark scope.
(c) Start the engine, and keep it at idling speed.
(d) Turn steering wheel from left bottom to right bottom for
several times to make oil temperature increase.
Oil temperature: 80°C
Normal
Abnormal
200
Normal
Abnormal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст