Geely FC. Manual part — 60
Geely FC. Manual part - 60
Air conditioner--Condenser Assembly
(b) Disassemble two bolts.
(c) Pull the component on the top of water tank assembly back
to disassemble the condenser assembly.
6. Disassemble the drier
(a) Use 10mm hexagon wrench to disassemble the cover and
filter core from regulator.
(b) Disassemble two O-shape rings from the cover.
(c) Use the acutilingual pliers to disassemble the drier.
7. Assemble the drier.
(a) Use the acutilingual pliers to assemble the drier.
(b) Put the O-shape ring in the cover.
(c) Spread freezing lubricant at the connecting part between
the O-shape ring and the cover.
Refrigerant oil: 100PG
(d)Use the 10mm hexagon wrench key to assemble the cover
to condenser assembly.
Torque: 12.3 N
⋅⋅⋅⋅⋅
m
8. Assemble condenser assembly.
9. Assemble Refrigerant NO.1 high pressure hose.
(a) Disassemble the cover from the tie –in of the pipe.
(b) Daub enough Refrigerant oil to lubricate at the connecting
part between the O-shape ring and the cover.
Refrigerant oil: 100PG
(c) Use the bolt to connect Refrigerant high pressure hose
with condenser assembly.
Torque: 5.1 N
⋅⋅⋅⋅⋅
m
Inner hexagon
socket wrench
Adjuster
237
Air conditioner--Condenser Assembly
10.
Assemble the Refrigerant liquid pipe A.
(a) Disassemble the cover from the pipeline joint.
(b) Assemble the O-shape ring to the Refrigerant liquid pipe
A.
(c) Spread enough Refrigerant oil to lubricate at the conencting
part between the O-shape ring and the cover.
Refrigerant oil: 100PG
(d) Use the bolt to connect the Refrigerant liquid pipe A with
condenser assembly.
Torque: 5.4 N
⋅⋅⋅⋅⋅
m
11. Fill with Refrigerant.
Regulated quantity: 660
±±±±±
10g
12. Warm the engine.
13. Check whether the Refrigerant leaks.
238
Supplemental restraint system--Note
Note:
When making repair, please make malfunction diagnosis by the flash light and malfunction diagnosing device
according with the method regulated in this operation manual at first, at the same time, it is necessary to check
whether there is any malfunction code before disassembling battery wire.
Forbid disassembling or repairing at any non-appointment repair station
Do not assemble any safety lever or bumper at the front of automobile, this will influence the performance of this
airbag.
People for repairing, disassembling and assembling should be trained specially.
When disassembling steering wheel assembly, it is necessary to make steering wheel right, only this could disas-
semble steering wheel assembly and make helix cable locate correct position, or it will damage helix cable assembly.
ECU matches with the technical parameter of electric system, forbid using the SRS parts of other automobiles, at
the same time, it is necessary to use new product to replace any part.
When repairing automobile (especially electric welding), it is necessary to close key switch, and it is best to cut off
the anode of battery.
After unfolding airbag, safety airbag assembly and helix cable assembly should be changed completely.
When disassembling or carrying airbag assembly, trim cover should face the upside; safety airbag assembly
could not superpose directly to avoid make wrong explosion and make any accident.
The inner malfunction of controller (ECU) could not repair, if it happens any malfunction, change it.
Safety airbag assembly should be stored in the environment whose temperature is lower than 40C, relative humid-
ity is lower than 75% and is apart from electromagnetic interruption.
Forbid disassembling the airbag assembly and gas generator in it.
Forbid connect AC or DC with over 20V with ECU to avoid damage.
Supplemental restraint system
Note
Warning:
This product is the SRS (supplemental restraint system) equipped by JILI “YUANJIN vision” type automobile, when
the automobile frontal face is impacted heavily, this product could reduce the possible hurt for driver and passen-
ger at the front seat, but this product could not replace the safety belt. For SRS is supplemental restraint safety
system, the driver should tie safety belt. This product is single-point electronic dual-airbag system whose charac-
teristic is that all sensors and control circuits are assembled in control box and gas maker is protechny. At the
same time, this product accords with the enterprise standard “Automobile safety airbag equipment” (Q/JL001—
2001) to product.
In repairing process, if it does not accord with correct operation sequence to operate, SRS might happen the
accidental explosion to make heavy accident. If repair does not accord with correct procedure, even if repair does
not incur accident, SRS might disable when automobile happens accident, for example, it could not explode by
the requirement. So, when making repair (including disassembling, assembling, checking or changing any part),
it is necessary to operate by correct sequence regulated by repair manual.
It is necessary to confirm following works before repairing: 1. Put the ignition switch at “OFF” state. 2. Disconnect
the cathode connection of battery, and make repair after waiting for 60s. In addition, disassembled cathode
should be twisted by insulating tape to insulate. (Capacitor in ECU could keep some electric power after battery
is cut off to unfold safety airbag in some time. So, when making maintenance, if it does not wait for some time
before operating, it might incur heavy hurt accident for wrong expansion of safety airbag.)
Do not put the parts of SRS directly under the insulation of hot air or flame.
239
Supplemental restraint system--Note
Special tools and measurers which any safety airbag repairing position should have:
Changeable subassembly which safety airbag repairing position should have:
a. Safety airbag assembly at the side of driver;
b. Safety airbag assembly at the side of passanger;
c. Helix cable assembly.
d. ECU assembly;
e. Steering wheel.
I.
Safety airbag joint
No.
Item
Applicable
(1)
Terminal dual-locking organization
(2)
Airbag anti-explosive organization
Joint 3, 4, 7, 8
(3)
Checking organization of electric circuit connection
(4)
Inadequacy connection protection organization
Joint 4
(5)
Joint dual-locking organization
Joint 2
(6)
Joint dual-locking organization
Joint 6, 7, 10
Safety airbag at the
side of passenger
Safety airbag at
the side of driver
Helix
cable
Airbag controller
1. All safety airbag joints should be yellow to be easy to distinguish the joints on other automobile parts,
this could guarantee the safety performance and reliability of safety airbag joint, each kind of joint has
special function and design.
240
Number
a
b
c
d
e
Function
Disassemble airbag subassembly on steering wheel
Assemble and disassemble big nut on steering column
Assemble and disassemble ECU and safety airbag assembly
at the side of passenger on automobile body.
Used for electric measurement on wiring harness
Used for resistance measurement of electric ignition device
of airbag subassembly.
Name and type of tool
5S hexagon wrench
Socket wrench 18S
14S socket wrench
Numeric multi-meter DT 992 type
Electric detonator tester
QJ992 type
Short
wiring
harness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст