Geely CK (2008). Manual part — 81
Geely CK (2008). Manual part - 81
321
(IV) Rear inside trim
1
Inner rear view mirror
10
Rear doorinside trim
2
Interior lamp
11
C- pillar upper inside trim
Rear seat belt buckle
(See rear seat belt buckle
removal/installation) rear trunk
inside trim
4
Sun visor
13
Rear trunk lower trim cover
5
B- pillar upper inside trim
14
Lower rear trim assembly
Rear seat
(See rear seat removal/installation)
Front seat belt
Rear seat belt
(See front seat belt
removal/installation)
(See Rear seat belt
removal/installation)
(See seat belt inspection)
(See seat belt inspection)
8
B- pillar lower inside trim
17
Rear door sill inside trim
9
Safe handle
18
Carpet & sound insulator
7
16
3
A- pillar inside trim
12
6
Roof inside trim
15
322
Section 2 Inside & Outside Trim and Accessories Removal and
Installation
(I) Front Bumper
The structure is as shown in the figure below:
1. Front Bumper
2.Front Bumper Fixed Screw
3.Secondary Bumper Assembly Upper Buckle and Plug
4.Mounting Plate Cross Head Counter Sunk Self-tapping Screw
5.Mounting Plate Cross Head
Counter Sunk Self-tapping Screw
6.Front Bumper Mounting Bracket to Body Bolt
7.Front Bumper
Mounting Bracket Sub-assembly
8. Secondary Bumper Assembly
9.Front Bumper Mounting
Bracket to Secondary Bumper Assembly Bolt
10.Front Bumper Cushion
1 1.Secondary Bumper
Assembly Lower Buckle and Plug
12.License Mounting Plate Assembly
13.Secondary Bumper As-
sembly Lower Connecting Bolt 14.Front Bumper Mounting Plate Seat
15.Mounting Plate Seat Bolt
16.Front Bumper Mounting Plate
323
1. Front Bumper Removal and Installation
(1) Disconnect the negative (--) terminal cable from the battery. Disconnect fog lamp wire;
(2) Remove the mudguard skirt to front bumper clip;
(3) Remove the attaching bolt of the the front fender and panel and the front bumper sub-assembly;
(4) Remove the front bumper set screw and the clip. Remove the front bumper mounting plate and the
positioning screw of the seat;
(5) Remove the bolt which connecting front bumper mounting bracket with the vehicle body;
(6) Pull the front bumper assembly and the secondary bumper assembly together out of the vehicle body.
Separate the front bumper mounting bracket from the rail, front bumper mounting plate from the front
bumper mounting plate seat;
(7) Remove the front bumper mounting plate seat from the vehicle body;
(8) Remove the secondary bumper assembly and the front bumper mounting bracket sub-assembly;
(9) Remove front bumper mounting plate;
(11)Remove front bumper cushion. Remove the front license plate. Remove the mounting plate assembly;
(12)Remove fog lamp;
(13)The installation is in the reverse order of the removal.
2.Notice For Removal Of The Front Bumper
(1) Pull the front bumper to separate it from the bumper rail.
(2) Uniformly pull it by force to prevent the front bumper mounting plate and seat from damage.
Warning
If the front bumper is only separated from the bumper rail on one side, the bumper may drop
and result in body hurt. Be careful not to drop the bumper when separating the front bumper
from the bumper rail.
3.Notice for installation of the front bumper
(1) Press the front bumper connecting part to the vehicle body and connect the rear bumper mounting
bracket assembly with the bumper rail.
(2) Be sure to insert the front bumper mounting plate seat into the bumper mounting plate.
324
(II) Engine Hood
Engine Hood Removal / Installation
For engine hood installation, see the figure
1. Removal
Warning
• It is dangerous to remove the engine hood without support. The engine hood may drop and
result in body injury. Work with at least one assistant when removing the engine hood and
should follow the procedures below:
1
Disconnect windshield washer hose.
2
Lift up the engine hood and support it with the spring brace;
3
Remove 2 spring braces under the help of the assistant to prevent the engine hood from dropping down
and resulting in body injury;
4
The assistant lifts the engine hood, removes the engine hood hinge bolt and the engine hood;
5
Remove the ventilator louver and remove the hinge arm;
6
Remove the hinge arm bracket attach bolt. Remove the hinge arm bracket from the body;
7
Remove the engine hood lock;
8
Remove the engine hood lock control cable.
2.Installation
1
The installation is in the reverse order of the removal;
2
Adjust the engine hood;
Engine Hood
Gas Spring Brace
Engine Hood Hinge
Engine Hood Lock Control Cable
Engine Hood Lock
Engine Hood Installation Illustration
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст