Geely CK (2008). Manual part — 50
Geely CK (2008). Manual part - 50
197
III. WIPER SWITCH ASSEMBLY REPLACEMENT
1. DETACH STEERING WHEEL ASSEMBLY
(a) Disconnect the main power source of the vehicle.
(b) Remove the passenger SRS module assembly, and cautiously put it in a safe place.
(c) Loosen steering wheel lock-bolts and remove the assembly.
2. REMOVE WIPER SWITCH
(a) Disconnect the connector.
(b) Remove the 2 tapping screws that are for mounting the wiper switch, take out the wiper switch from the
bracket of the combination switch.
IV. WASHER NOZZLE
ADJUSTMENT
1. INSPECT WASHER NOZZLE
(a) Start the engine, check if the position where the washer fluid from the nozzle sprays the windshield is in
the central or upper of the area wiped by the blades.
(b) Change the direction (horizontal) of the nozzle hole to adjust the point where washer fluid sprays the
windshield.
198
Chapter 5 Light System
Section 1 Survey of Light System
I. COMPOSITION
1. Front combination lamp assembly: turn signal lamp, high beam, low beam, head lamp, front position lamp.
2. Rear combination lamp: turn signal lamp, back-up lamp, rear fog lamp, tail lamp, brake lamp, retro reflector.
3. Front fog lamp
4. Side turn signal lamp
5. High mounted stop lamp
6. Rear trunk lamp
7. License plate lamp
8. Interior dome lamp
9. Rear row reading lamp
10. Door lampshield and bulb assembly
II. NOTES FOR REPAIR
1. NOTES WHEN REPAIRING ELECTRICAL EQUIPMENTS
(a) Disconnect the battery ground cable.
2. Notes when replacing a headlamp bulb
(a) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(b) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(c) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(d) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground.The glass fragments will splash up.
(e) When replacing, make sure to use the bulbs with the same power, same model.
(f) After the bulb is installed, make the lamp holder tight.
199
III. BULB SPECIFICATIONS
Notes: All bulbs are made by Philips Corp..
Name
Specifications
Headlamp (High beam and Low beam)
H1 12V 55W
Turn signal lamp
P21W 12V 21W
Position lamp
W5W 12V 5W
Front fog lamp
H3 12V 55W
Rear combination lamp (Turn signal lamp)
PY21W 12V 21W
Rear combination lamp (Brake / Position lamp) P21/5W 12V 21/5W
Rear combination lamp (Rear fog lamp)
P21W 12V 21W
Rear combination lamp (Back-up lamp)
P21W 12V 21W
C5W 12V 5W
W5W 12V 5W
Rear row reading lamp
C5W 12V 5W
Side turn signal lamp
WY5W 12V 5W
High mounted stop lamp (incl. rear trunk lamp)
W5W 12V 5W
License plate lamp
W5W 12V 5W
Door courtesy lamp
W5W 12V 5W
Interior lamp (dome lamp)
200
IV. LOCATION OF LIGHT SYSTEM
Fuse Box
Interior Lamp
Rear Row
Reading Lamp
LH Turn Lamp Assembly
Lamp Assembly
LH Front Fog Assembly
Front Headlamp Height
Adjusting Switch
Headlamp Switch Lamp
Control Switch, Haedlamp
DIM Switch Turn Signal
Lamp Switch
Hazard Warning
Switch
Parking Brake Switch
Backup Lamp Switch
Brake Switch
Door Courtesy Lamp Switch
LH/Front, Rear Door
Courtesy Lamp Assembly
LH Front Combined
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст