Geely CK (2008). Manual part — 68
Geely CK (2008). Manual part - 68
269
6
Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect them with the two terminals of the battery removed from the
vehicle and deploy the airbag (see the figure below).
7
The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
(3) Deploy outside the vehicle
NOTICE:
Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.
1
Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery
from the vehicle.
2
The airbag assembly shall be deployed according to the following procedures.
(4) Driver airbag assembly
1
Remove the driver airbag assembly from the vehicle.
Vehicle Cover
Wire Harness
for Deployment
NOTICE
Make sure there is no man inside or near the vehicle and then carry out the operations.
After the driver airbag is deployed, the gas generator is of high temperature. Keep it for 30 minutes until it
gets cool for use.
If the driver airbag assembly cannot be deployed, discuss the problem with the local Geely service station.
NOTICE
Work must be started 60s after removal of the battery.
NOTICE
When the connector is not connected, the terminals of the driver airbag assembly will be short circuited
automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,
the deployed surface should face up. It should be kept on a flat surface without any other items on it.
270
2
Prepare two 6m plus wire harnesses for deployment, connect the other two ends to avoid unexpected
deployment in case of static electricity (see the figure below).
3
Touch the body of the vehicle with hands for static electricity elimination.
NOTICE:
The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall
therefore be performed strictly.
4
Cut off the wire harnesses of the driver airbag assembly and connect them with the two wire harnesses
for deployment, and make sure to wrap up the connecting location with insulating tape for insulation (see
the figure below).
5
Install the unused bolts on to the inside bolt of the driver airbag assembly, and tie a thick wire securing the
wheel rim.
6
Pass the deployment wire harness of the driver airbag assembly through an old tire with rim, and fix
upwards the driver airbag assembly by means of the wire connected to the bolts, etc (see the figure
below).
Wire Harness for Deployment
Short Circuit Locatio
n
6m plus
Passenger Airbag
Wire Harness
for Deployment
Short
Circuit
Location
Insulating Tape
Airbag Assembly
Wire Harness
for Deployment
271
7
Put three old tires without hubs onto the tire used to fix the driver airbag assembly (see the figure below).
8
Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect with the two terminals of the battery removed from the vehicle
and deploy the airbag (see the figure below).
9
the deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
Wire Harness for Deployment
Old Wheels
without Hub
Wire Harness
for Deployment
NOTICE
Make sure to deploy the driver airbag assembly when there is no person close by.
After the driver airbag is deployed, the gas generator is of high temperature. Keep it for over 30 minutes
until it gets cool for use
272
Chapter 8 MK-20 ABS System
Section 1 ABS Diagnosis
I. Check the ABS Warning Light
1. Check the ABS Warning Light goes on as the following:
1
Turn the ignition switch to ON, the ABS Warning Light goes on for about 1.7 seconds and then goes off.
2
If the above condition is not satisfied, it indicates that there is a fault, please check the DTC.
3
If the warning light does not light up at all, refer to the Non-DTC fault inspection table.
II. The Reading of the information status
After connecting the scan meter, turn the ignition switch to¡°ON¡±, select the function menu item 01, press
OK to confirm, the screen will display the following information:
1. ECU drawing number and its version:
ABS MK20 IE
2. Code 01901
III. Read and Clear the DTC
1. After selecting the "02 Read DTC" in the function menu, it displays the total amount of the fault, if there
is no DTC, then it displays no DTC. Then, press OK button to proceed to next page to review the DTC
and its description. Generally, there is a P or O before the DTC, indicating that it is a Persistent fault or
Occasional fault. Persistent fault remains existing all the time, while the Occasional fault can be cleared
and is only able to reoccur during the driving.
Note:
The reading of the DTC can not be quitted middle way, you can return to the function menu only
after reading all the DTC.
Clear DTC
2. Select function menu item 05, press OK button to clear the DTC, if the DTC can not be cleared, it
indicates that the DTC represent exist all the time, if the saved DTC can be cleared, it indicates that it is
occasional fault can only be detected during the driving.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст