Geely CK (2008). Manual part — 30
Geely CK (2008). Manual part - 30
117
Section 2 Rear Suspension
Components
LR Strut
Assembly
LR ABS
Sensor
W
ire
Harness
LR Brake
LR Brake Pipe
Clip
Clip
RR Strut
Assembly
Clip
RR
ABS Sensor
W
ire Harness
RR Brake Hosex2
No. 2
T
ransverse
Arm
Left T
railing
Rod
Assembly
Body
Body
Body
Body
No. 1
T
ransverse
Arm
No. 1 Rocker
Arm
Clip
RR Brake Pipe
RR Brake Hose
RR Brake
Right T
railing
Rod
Assembly
Rear Stabilizer Bar
Assembly
No. 2
T
ransverse
Arm
Rear Stabilizer Bar Retainer
Rod Components
118
Section 3 Rear Wheel Alignment
Inspection
1. Inspect tire
Standard inflation pressure: 220 Kpa
2. Inspect rear wheel toe-in
If the rear wheel toe-in is not within the specification, adjust it via rear
wheel toe-in adjusting cam.
3. Inspect the camber
Notice: If the camber is not within the specification, check the suspension parts for damage/low
performance. Replace it if necessary.
Toe-in
C - D: 1
~
5 mm
C a m b e r
- 20 ´± 3 0 ´
Front
No. 2 Transverse Arm Assembly
Rear Wheel Toe-In
Adjusting Panel
Rear Wheel Toe-In
Adjusting Plate
No. 2 Transverse
Arm Assembly
No. 1 Transverse
Arm Assembly
No. 1 Transverse
Arm Assembly
Rear Wheel Toe-In
Adjusting Cam
Rear Wheel Toe-In
Adjusting Cam
Body Bottom Plate
119
Section 4 Left & Right Rear Strut Assembly
Components
Replacement
1. Remove the rear wheel
2. Remove ABS sensor
(1) Remove ABS rear wheel sensor retaining bolt. Remove the sensor.
(2) Remove the retaining bolt of ABS rear wheel sensor on rear shock absorber bracket
3. Separate brake pipe and rear strut assembly
Remove the elastic clip on the pipeline bracket attaching the brake pipeline
Cushion (Dumper)
Dust Prevent
Sleeve
Rear Suspension
Spring Lower
Insulator
Rear Left
Shock Absorber
Upper Mount
Cushion
Upper Mount
Rear Suspension
Spring Insulator
Rear Suspension Conical Spring
120
4. Remove the left and right rear strut assembly
(1) Remove the threaded connect of the rear strut assembly and rear brake assembly
(2) Remove the 3 nuts attaching the rear suspension upper mount to the body
Caution: reliable object shall be used to support the rear brake assembly! Make sure that the
brake pipeline is not affected or damaged!
5. Disassembly the left, right rear strut assembly
(1) Set the rear strut assembly with special tool. Remove the nut on the top of the
rear shock absorber piston
Caution: The spring may rebound!
(2) Remove the rear suspension upper mount, rear suspension upper mount cushion,
rear suspension spring upper insulator, rear suspension spring, rear shock absorber
cushion, rear shock absorber dust preventing sleeve, rear suspension spring lower insulator in order
6. The assembly is in the reverse order of the disassembly.
Caution:
(1) when installing the nut on the shock absorber piston rod upper end, use special fixture
and be careful that the spring may rebound!
Torque : 32~38N.m
(2) Rear strut assembly to body thread torque : 32~38 N.m
(3) Strut assembly to rear brake assembly thread torque : 81~96 N.m
(4) Install the ABS rear wheel sensor and the secure the signal wire
(5) When securing the brake line, make sure that the brake line does not interfere with
other parts
(6) Wheel nut torque : 95~115N.m
(7) Check the brake system for leakage, bleed air in the brake system as necessary
(8) Check whether the ABS signal is normal
(9) Check rear wheel alignment, adjust it as necessary
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст