Geely Emgrand X7. Manual part — 530

11.4.7.13 Hazard warning lamp do not work

Circuit diagram:

NL11-4049b

D DR08

G DR08

6 SO31

3 SO31

8 CA12

8 IP48

6 IP50

7 IP48

9 IP48

5 CA12

8 CA18

5 CA18

6 SO24

3 SO24

D DR18

G DR18

10A

IF04

1 IP07 4 IP07 3

OFF

ON

1

4

左后视镜
(左侧转向灯）

左后组合灯
(左转向灯)

左前组合大灯
(左转向灯）

右前
组合大灯
(右转向灯）

右后组合灯
(右转向灯）

右后视镜
(右侧转向灯）

危险警告
开关

BCM

TURN-LH LAMP

TURN-RH LAMP

HAZARD

P-TURN LAMP

Diagnostic steps:

1

Confirm whether the steering work light is normal.

(a) Ensure whether turning lamp works normally.

2

Repair the circuit from the fuse IF04 to the terminal No. 1 of the hazard warning switch
IP07.

(a) Rotated ignition switch to "OFF" position.

(b) Disconnect hazard warning lamp switch harness connector.

(c) Measure resistance between fuse IF04 to danger warning lamp switch wire harness connector

IP07 terminal No. 1.

Standard resistance: less than 1 Ω

No

See 11.3.7.12 steering lamp does not work.

Yes

Hazard
warning
switch

Left rearview
mirror ( left
side steering
lamp)

Left rear
combination
lamp (left
steering lamp)

Left front
combination
headlamp (left
steering lamp)

Right front
combinatio
n
headlamp
(right
steering
lamp)

Right
rearcombin
ation lamp
(right
steering
lamp)

Right
rearview
mirror (right
side steering
lamp)

2119

Confirm if the resistance conforms to
standard value.

NL11-4039b

IR05

8 5

8 6

8 7

3 0

IR02

8 5

8 6

8 7

3 0

IR07

8 5

8 6

8 7

3 0

4

IR01

2

1

5

3

4

2

1

5

3

IR04

IR03

8 5

8 6

8 7

3 0

IF 1 4

IF
2

9

IF
3

2

IF
3

3

IF
3

4

IF
3

5

IF
1

8

IF 2 0

IF 11

IF
2

5

IF
2

6

IF
2

7

IF
2

5

IF
0

1

IF
0

2

IF
0

3

IF
0

4

IF
0

5

IF
0

6

IF
2

6

IF
2

7

IF
2

3

IF

30

IF

1

2

IF

1

6

IF

1

7

NL11-4050b

IP07 危险警告灯开关线束连接器

2

6

5

4

3

1

1

3

Inspect the grounding voltage of the terminal No. 4 of the hazard warning lamp switch
wire harness connector IP07.

No

Repair or replace the harness.

Yes

IP07hazard warning lamp

switchharness connector

2120

(a) Connect danger warning lamp

switch wire harness connector.

(b) Open

hazard warning lamp

switch.

(c) Measure grounding voltage of

danger warning switch wire
harness connector IP07 terminal
No. 4.

Standard voltage: 11-14 V

Confirm if the voltage conforms to
standard value.

NL11-4051b

IP07 危险警告灯开关线束连接器

2

6

5

4

3

1

4

4

Repair the wire harness between the terminal No. 4 of the hazard warning lamp switch
wire harness connector IP07 and the terminal No. 6 of the BCM wire harness connector
IP50.

(a) Rotated ignition switch to "OFF"

position.

(b) Separately

disconnect

danger

warning lamp wire harness
connector and vehicle body
control module wire harness
connector 4.

(c) Measure resistance between

warning lamp switch IP07
terminal No. 4 and vehicle body
control module wire harness
connector 4 IP50 terminal No. 6.

Standard resistance: less than 1 Ω

Confirm if the resistance conforms to
standard value.

NL11-4051b

IP07 危险警告灯开关线束连接器

2

6

5

4

3

1

4

No

Replace hazard warning lamp switch, Refer
to11.3.8.17 replace hazard warning lamp switch.

Yes

IP07hazard warning lamp

switchharness connector

IP07hazard warning lamp

switchharness connector

2121

NL11-4052b

IP50 车身控制模块线束连接器4

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

6

5

Replace the BCM

(a) Replace BCM and refer to Replacement of BCM in 11.8.8.1.

Confirm the completion of repair.

16

The system is normal.

Next

No

Repair or replace the harness.

Yes

IP50body control module harness

connector4

2122