Geely Emgrand X7. Manual part — 601
Geely Emgrand X7. Manual part - 601
11
The system is normal.
Next
2403
11.8.7.5 Sunroof can not open
Circuit diagram:
Refer to 11.8.7.4 sunroof can not work.
Diagnostic steps:
1
Inspect the sunroof switch
(a) Disconnect the Sunroof switch
harness connector RF13.
(b) Operate the Sunroof switch to
open the slide.
(c) Measure the resistance between
terminals No.8 and No.5 of the
sunroof switch harness connector
RF13 with a multimeter.
Standard resistance: less than 1 Ω
Confirm whether the resistance is at a
specified value.
1
2
3
4
5
6
7
8
9
10
NL11-0021c
RF13 天窗开关线束连接器
(a) Replace sunroof switch assembly and refer to 11.2.8.3 "Replacement of Sunroof Switch
Assembly".
Confirm whether the sunroof can be opened by sliding.
(a) Rotated ignition switch to "OFF" position.
(b) Disconnect the battery negative cable.
(c) Disconnect Sunroof module harness connector RF07.
(d) Disconnect the sunroof switch harness connecter RF13.
2
Replace the sunroof switch assembly.
3
Check the energy transmission ability of the signalling circuit of the sunroof switch and
module.
Yes
The system is normal.
No
Yes
Go to step 3
No
RF13 sunroof switchharness
connector
2404
(e) Measure the resistance between terminal No.5 of the sunroof module harness connector RF07
and terminal No.8 of sunroof switch wiring harness connector RF13 with a multimeter.
Standard resistant value: is less than 1Ω
Is the resistance at a specified value?
4
Repair the signalling circuit from the sunroof switch to the Sunroof module.
(a) Repair the trouble spots between terminal No.5 of the sunroof module harness connector
RF07 and terminal No.8 of the Sunroof switch harness connector RF13.
(b) Connect the sunroof switch harness connection RF13.
(c) Connect the sunroof module harness connecter RF07.
(d) Connect battery negative cable.
(e) Turn ignition switch to "ON" position.
(f) Operate “slide on” of the sunroof switch.
Confirm whether the “slide on” of sunroof switch works normally.
A. For the Replacement of the Sunroof motor assembly, please refer to 11.2.8.2 Replacement of
Sunroof Motor.
Confirm the completion of repair.
8
The system is normal.
5
Replace the sunroof module
Next
Yes
The system is normal.
No
Yes
Go to step 5
No
2405
11.8.7.6 Sunroof can not close
Circuit diagram:
Refer to 11.8.7.4 sunroof can not work.
Diagnostic steps:
1
Inspect the sunroof switch
(a) Disconnect the sunroof switch
harness connector RF13.
(b) Measure the energy transmission
ability between switch terminals
No.6 and No.5 with a multimeter.
Standard resistance: less than 1 Ω
Is the resistance at a specified value?
1
2
3
4
5
6
7
8
9
10
NL11-0021c
RF13 天窗开关线束连接器
(a) Replace the sunroof switch assembly, Refer to 11.2.8.3 replacement of sunroof switch
assembly.
Confirm whether the sunroof is working properly.
(a) Rotated ignition switch to "OFF" position.
(b) Disconnect the battery negative cable.
(c) Disconnect sunroof module harness connector RF07.
(d) Disconnect sunroof module harness connector RF13.
2
Replace the sunroof switch assembly.
3
Check the breakover condition of the circuits of sunroof module and sunroofswitch.
Yes
The system is normal.
No
Yes
Go to step 3
No
RF13 sunroof switchharness
connector
2406
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст