Geely Emgrand X7. Manual part — 331
Geely Emgrand X7. Manual part - 331
3.5.7.16 P0729 P0731 P0732 P0733 P0734 P0735 P0736
1. DTC
description:
DTC P0729 6th speed transmission ratio error
DTC P0731 1st speed or M1 speed transmission ratio error
DTC P0732 2 nd speed transmission ratio error
DTC P0733 3rd speed transmission ratio error
DTC P0734 4th speed transmission ratio error
DTC P0735 5th speed transmission ratio error
DTC P0736 Reverse gear transmission ratio error
The transmission gear shift is controlled by the transmission control unit (TCU). The transmission control unit
receives the input information from the engine RPM sensor and other vehicle sensors. During each gear shift, it
selects the time to change gear, controls the gear shift feel and the hydraulic torque converter clutch (TCC).
2. Conditions For Setting DTC and The Fault Position :
DTC Code DTC Detection Strategy
Conditions For Setting The DTC
(Control Strategy)
Fault Position s
P0729
When do not shift ,system
observed transmission ratio of
6th speed is over the standard
value
P0731
It is observed that the
transmission ratio when the
shift gear is in the 1st speed
position exceeds the
calibration value when no gear
shift is carried out.
1. ignition switch is in ON
position
2. Engine speed>300 rpm
3. Engine is in the LHM
4. Transmission
oil
temperature
>0°C
5. Output shaft speed of
transmission>300 rpm
1. Automatic
transmission fluid
2. Automatic
transmission fluid
level
3.
AutomaticTransmissi
on assembly
1323
P0732
When do not shift , system
observed transmission ratio of
2nd speed is over the standard
value
P0733
When do not shift , system
observed transmission ratio of
3rd speed is over the standard
value
P0734
It is observed that the
transmission ratio when the
shift gear is in the 4st speed
position exceeds the
calibration value when no gear
shift is carried out.
P0735
It is observed that the
transmission ratio when the
shift gear is in the 5th speed
position exceeds the
calibration value when no gear
shift is carried out.
P0736
It is observed that the
transmission ratio when the
shift gear is in the Gear R
position exceeds the
calibration value when no gear
shift is carried out.
6. Transmission shift lever is
not in N speed and parking
position.
3. Circuit
sketch
1324
T
C
U
电磁阀
换挡器
档位开关
LEVER
REVERSE
START
VBS5
VBS6
VBS7
V
BS8
VBS9
VBS1
0
O
n
O
ff
1
O
n
O
ff
2
O
n
O
ff
3
O
n
O
ff
4
EMM
INPUT
SHAFT
SPEE
D
SENSOR
OU
TPUT
SHAFT
t
SPE
ED
SENSOR
25
26
10
11
9
8
13
12
24
23
22
21
20
7
6
5
4
3
2
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
1
18
8
1
3
2
12
14
4
11
12
9
10
15
2
1
4
3
6
5
7
7
J-5
5
16
17
J-5
4
J-5
1
J-5
6
J-5
2
J-5
3
4
11
10
10
15
3
CAN H
启动继电器
倒车信号
输出
主继电器
JF-1
IG2
JB-2
CAN L
10
20
J-3
J-1
J-3
J-2
J-2
J-3
J-3
J-3
J-1
8
J-3
J-3
J-3
J-3
J-3
J-3
J-3
J-3
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
IF36
NL03-2005c
4. Diagnostic
procedures:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and analyze the
accuracy of the data, as these will help with quick diagnosis.
1
Read the fault code again after clearing away the fault code to Check if fault codes, except DTC
P0729, P0731, P0732, P0733, P0734, P0735 and P0736 exist in the control system.
A. Connect fault diagnosis tester to the datalink connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic device power supply
D. Clear DTC code.
E. Reset reading fault code, and check if DTCs meet setting condition of fault code in current
DTC Codes Shown
To Step
DTC P0729 P0731 P0732 P0733 P0734 P0735 P0736
Yes
DTCs other than DTCs P0729, P0731, P0732, P0733, P0734, P0735 and P0736
No
Gears switch
Main relay
JF-1
Reverse output
signal
Start relay JB-2
Shifter
Electromagnetic
valve
1325
2
Check if the automatic transmission leaks oil.
3
Check if the Automatic transmission oil level and oil quality accord with the standard.
See 3.5.7.2 Automatic transmission oil level inspection procedures
4
Check if the automatic transmission has obvious mechanical damage.
5
Replace Automatictransmission assembly
Replace Automatictransmission assembly , refer to3.5.7.6 Automatictransmission assembly replacement
6
Go to automatic transmission fresh process.
Refer to3.5.7.4 Automatic transmission refresh process
7
Use fault diagnosis tester to confirm if DTC is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switches to ON position.
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
No
Yes
Refer to3.4.7.6 fault diagnosis code (DTC) chapter
index
No
Yes
Refer to 3.4.7.3 Replacement procedure of
automatic transmission oil to fill or replace
automatic transmission oil.
No
Yes
Repair or replace the damaged part
Yes
No
Repair or replace the fault part
Next
Next
1326
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст