Geely Emgrand X7. Manual part — 620
Geely Emgrand X7. Manual part - 620
is under the
alarm state, the
vehicle
The anti-theft
horn does not
ring.
If it is confirmed that horn circuit is
normal after inspection, replace BCM.
See 11.8.8.1 Replacement of BCM.
Danger warning lamp circuit.
Be capable of opening the steering
lamp (hazard warning lamp). If all
steering lamps do not work, inspect
the steering lamp circuit.
When the
anti-theft system
is under the
alarm state, the
hazard alarm
lamp does not
flicker.
If all turning lamp doesn't work after
inspection, replace BCM.
If all steering lamps do not work,
replace BCM. Refer to 11.8.8.1
Replacement of BCM.
2479
11.9.7.5 Anti-theft indicator lamp do not work
Circuit diagram:
NL11-2155b
IP ALT
4 IP49
6
15A
IF14
1 SO23
HORN OUTPUT
ALM LED
85
87
86
30
BCM
2 SO23
防盗喇叭
报警继电器
B
G14
IP39
2 IP39
12 IP49
防盗报警灯
Diagnostic steps:
Notes:
Prior to the implementation of the diagnostic procedures, firstly make use of the fault diagnostic
unit, and then select body control system/BCM special set function/anti-theft indicator lamp in
sequence. Compel to turn on the anti-theft indicator lamp, which is conducive to quickly
troubleshoot.
1
Measure voltage between the alarm indicator harness connector IP14 terminal No.2.and
No.6.
(a)
Disconnect the anti-theft
indicator harness connector IP14.
(b)
Measure voltage between
terminal No.2 and No.6 with a
universal meter.
Standard voltage: 11-14 V
Confirm if the voltage conforms to
standard value
NL11-2156b
2
6
5
4
3
1
IP39 防盗指示灯线束连接器
2
6
Alarmrelay
Anti-theft horn
Anti-theft
alarm lamp
IP39immobilizer indicator light
harness connector
2480
.
2
Check ground circuit of anti-theft indicator.
(a)
Disconnect the anti-theft
indicator harness connector IP14.
(b) Measure voltage between harness
connector terminal No. 6 and
vehicle body ground point with a
universal meter.
Standard resistance: less than 1 Ω
Confirm if the resistance conforms to
standard value.
NL11-2157b
2
6
5
4
3
1
IP39 防盗指示灯线束连接器
6
3
Repair ground circuit of anti-theft indicator.
a) Repair fault point from anti-theft indicator to body ground circuit.
Is the anti-theft indicator working correctly?
4
Check supply circuit of anti-theft indicator.
Yes
The system is normal.
No
Yes
Go to step 4
No
No
Go to step 6
Yes
IP39immobilizer indicator light
harness connector
2481
(a) Rotated ignition switch to "OFF"
position.
(b) Disconnect the battery negative
cable.
(c)
Disconnect BCM harness
connector IP49.
(d)
Disconnect the anti-theft
indicator harness connector.
(e) Measure the resistance between
terminal No. 2 of anti-theft
indicator harness connector IP14
and BCM harness connector IP49
with a universal meter.
NL11-2158b
2
6
5
4
3
1
IP39 防盗指示灯线束连接器
2
NL11-2159b
IP49 车身控制模块线束连接器3
1
2 3
4 5 6
7
8 9 10
11 12 13 14 15 16 17 18 19 20
12
Test Items
Specified Value
IP49(12)—IP14(2) Less
than
1
Ω
Is the resistance at a specified value?
5
Replace the BCM
A. Replace BCM and refer to Replacement of BCM in 11.8.8.1.
Confirm the completion of repair.
No
Repair open circuit fault between terminal 2 of anti-theft
indicator harness connector IP14 and BCM harness
connector IP49
Yes
IP39immobilizer indicator light
harness connector
IP49body control module harness
connector3
2482
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст