Geely Emgrand X7. Manual part — 403
Geely Emgrand X7. Manual part - 403
5
Replace ABS control module assembly
(a) Replace ABS control module assembly, Refer to 6,6,7,1 hydraulic electric control unit replacements.
(b) Connect to battery negative cable.
(c) Turn on ignition switch, confirm ABS warning lamp is ON.
(d) Make sure that the repair work is finished.
6
The system is normal.
Repair or replace the wire harness or the wire
No
Yes
Next
1611
6.6.6.11 Wheel Speed Sensor Malfunction Diagnosis
Diagnostic Trouble
Code (DTC)
Failure Type
C1200
Left front speed sensor wire fault(open circuit and short circuit)
C1201
Left front speed sensor signal fault (over range of signal. Interrupt of signal .signal
invalid and so on.)
C1203
Right front speed sensor wire fault(open circuit and short circuit)
C1204
Right front speed sensor signal fault (Overrange of signal, interrupt of signal ,signal
invalid and so on,)
C1206
Left rear speed sensor wire fault(open circuit and short circuit)
C1207
Left rear wheel speed sensor signal faults (signal exceeding range, signal interrupting
and signal invalidation etc.)
C1209
Right rear speed sensor wire fault(open circuit and short circuit)
C1210
Right rear speed sensor signal fault (Overrange of signal, interrupt of signal ,signal
invalid and so on,)
C1213
Wheel speed sensor frequency fault (the wheel speed difference is too large).
Notes:
This maintenance manual is only targeted at the troubleshooting of the front left wheel speed sensor.
Troubleshooting of other wheel speed senors is similar. See Diagnosis of Front Left Wheel Speed Sensor
Malfunctions.
Circuit diagram:
1612
NL06-1011b
3 CA13
78 EN01
17 CA13
7 IP12
16 CA13
13 IP01
32 CA13
30 CA13
2 IP56
4 CA13
13 CA13 38 CA13
31 IP01
R
18
2
CA13
CA16
6
1
CA13
CA16
34
2
CA13
CA07
22
1
CA13
CA07
10
A
IF34
1 CA13
40A
EF04
25 CA13
25A
EF03
IG
+BRAKE LIGHT SW
GND
GND
EBD WARING LMP
ABS WARING LMP
DIAGNOSTIC K
WP RR WS RR
WP FR
WS FR
WP FL
WS FL
WP RL WS RL
制动灯
开关
左后轮速
传感器
右后轮速
传感器
左前轮速
传感器
33
2
CA13
SO28
20
1
CA13
SO28
19
2
CA13
SO25
31
1
CA13
SO25
右前轮速
传感器
ABS控制模块
IG2
ALT
ECM
诊断接口
组合仪表
Diagnostic Steps:
1
Inspect the left front wheel speed sensor harness connector.
A. Inspect whether the left front wheel sensor harness connector is correctly connected.
2
Inspect the installation of the left front wheel speed sensor.
A. Check whether the front left wheel speed sensor is correctly installed.
B . Tighten torque: 10Nm(Metric)7 . 4lb-ft (English system)
3
Inspect the left front wheel speed sensor.
Connect the harness connector properly.
Correctly install the left front wheel speed
Yes
No
Yes
No
ABS control module
Right
rearspeed
sensor
Left rear
speed
sensor
Right
front
speed
sensor
Left front
speed
sensor
Brake
lamp
switch
Combination instrument
Diagnostic
s interface
1613
A. Test the front left wheel speed sensor with a
multimeter according to the following tables.
Note: rotate the wheel by hand when measuring.
B. Confirm whether the voltage and current are the
standard values.
NL06-1015b
2
1
CA07 左前轮速传感器线束连接器
2
1
Wheel speed sensor
Descriptions
Sensor type
Hall-type speed sensor
Signal current
Low level: 5.6 - 8.4 mA; high level: 11.2 - 16.8 mA
Clearance value with signal panel
Front axle 1.626 mm (0.064in)
Rear axle 0.597 mm (0.023 in)
4
Inspect the harness (that between the left front wheel speed sensor and the ABS control module).
(a) Disconnect left front speed sensor harness
connector.
(b)
Disconnect ABS control module harness
connector.
(c) Use multimeter to measure resistance between
connector CA13 terminal 34 and CA07 terminal
2.
(d) Use multimeter to measure resistance between
connector CA13 terminal 22 and CA07 terminal
1.
NL06-1016b
25
1
26
27
28
29
30
31
32
33
34
35
36
37
38
13
24
12
14
15
16
17
18
19
20
21
22
23
2
3
4
5
6
7
8
9
10
11
CA13 ABS控制模块线束连接器
34
22
Go to step 5
No
Yes
CA07Left front speed sensorharness connector
CA13ABS control module harness connector
1614
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст