Geely Emgrand X7. Manual part — 650
Geely Emgrand X7. Manual part - 650
(a) Disconnect
cigar lighter wire
harness connector.
(b) Meanwhile,
use
multimeter
to
measure resistance between cigar
lighter wire harness connector
IP30 terminals No. 1 and
grounding circuit.
Standard resistance: less than 1 Ω
Is the resistance at a specified value?
NL11-2225b
1
2
3
IP30 点烟器线束连接器
1
6
Repair the open circuit fault of the cigarette lighter grounded circuit.
(a) Repair short-circuits fault between cigar lighter wire harness connector IP30 terminal No. 1
and grounding.
Confirm whether the cigarette lighter works normally.
7
Replace cigarette lighter
A. Replace cigarette lighter, refer to“11.14.6.1 cigarette lighter replacement ”
Confirm the completion of repair.
8
The system is normal.
Next
Yes
The system is normal.
No
Yes
Go to step 7
No
IP30 cigarette lighter harness
connector
2599
11.15.5.4 Standby power supply socket can not be work
Circuit diagram:
NL11-2226b
备用电源
ACC
IP53
2
IP53
1
15A
IF21
Diagnostic steps:
1
Check fuses IF21.
(a) Check fuse IF21was blown
Rated Current of Fuse: 15A.
NL11-2227b
IR05
85
86
8 7
3 0
IR02
8 5
8 6
8 7
3 0
IR07
8 5
86
87
3 0
4
IR01
2
1
5
3
4
2
1
5
3
IR04
IR03
8 5
8 6
8 7
3 0
IF 1 4
IF
2
9
IF
3
2
IF
3
3
IF
3
4
IF
3
5
IF
1
8
IF 1 3
IF 11
IF
2
5
IF
2
6
IF
2
7
IF
2
0
IF
0
1
IF
0
2
IF
0
3
IF
0
4
IF
0
5
IF
0
6
IF
2
1
IF
2
2
IF
2
3
IF
2
1
IF
3
0
IF
1
2
IF
1
6
IF
1
7
2
Inspect the fuse IF21 circuit.
Yes
Go to step 3
No
Standby power
2600
(a) Inspect for short circuit.
(b) Repair the circuits. Confirm that there are no short circuits.
(c) Replace the fuses with rated current.
Confirm whether the standby power socket works normally.
3
Inspect the standby power socket power circuit.
(a) Make ignition switch turn to
ACC gear.
(b) Meanwhile,
use
multimeter
to
measure voltage of power supply
outlet wire harness connector
IP53 terminal No. 2.
Standard voltage: 11-14 V
Confirm if the voltage conforms to
standard value.
NL11-2228b
1
2
3
IP53 备用电源线束连接器
2
4
Repair the open circuit fault of the emergency power supply socket supply circuit.
(a) Repair short-circuit faults occurred between standby power supply outlet wire harness
connector IP53 terminal No. 2 and fuse IF21.
Confirm whether the standby power socket works normally.
5
Inspect the standby power socket grounding circuit.
Yes
The system is normal.
No
Yes
Go to step 5
No
Yes
The system is normal.
No
IP53 Standby power harness
connector
2601
(a) Disconnect wire harness
connector of standby power
supply outlet.
(b) Meanwhile,
use
multimeter
to
measure resistance between
standby power supply outlet wire
harness connector IP53 terminals
No. 1 and grounding circuit.
Standard resistance: less than 1 Ω
Is the resistance at a specified value?
NL11-2229b
1
2
3
IP53 备用电源线束连接器
1
6
Repair the open circuit fault of the emergency power supply socket grounding circuit.
A. Repair the fault point of the open circuit between the terminal No. 1 of the emergency power
supply socket wire harness connector IP53 and the grounded circuit.
Confirm whether the standby power socket works normally.
7
Replace the standby power socket.
A. Refer to 11.14.6.2 "Replacement of Standby Power Supply" to replace the standby power
socket.
Confirm the completion of repair.
8
The system is normal.
Yes
The system is normal.
No
Yes
Go to step 7
No
Next
IP53 Standby power harness
connector
2602
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст