Geely Emgrand X7. Manual part — 140
Geely Emgrand X7. Manual part - 140
2.8.7.8 Cooling Fan always Runs at High Speed
Note: When this fault is present, it is recommended to carry out diagnostic when engine is
completely cooled down.
1
Confirm Fault Symptom
2
Inspect the signal of temperature sensor of engine coolant.
(a) Rotated ignition switch to "OFF" position .
(b) Connect fault diagnosis tester to diagnosis testing interface.
(c) Turn
off
A/C
switch.
(d) Turn ignition switch "ON" position.
(e) Select in sequence: engine/data list/ engine coolant temperature.
(f) Observe the temperature displayed on temperature sensor of engine coolant. When the engine
is completely cool, the temperature displayed shall be higher than ambient temperature.
Confirm if the temperature displayed is normal.
3
Inspect the circuit between the 86 socket of the high- or low-speed relay 2 and the
terminal 17 of ECM harness connector EM01.
(a) Rotated ignition switch to "OFF"
position .
(b) Dismantle high speed relay 2.
(c)
Disconnect ECM harness
connector EM01.
(d) Measure the resistance with a
multimeter.
NL11-2251b
ER03
8 5
86
8 7
30
3 0
87
8 6
8 5
ER05
3 0
8 7
86
85
ER06
30
87
87 a
8 6
8 5
ER11
ER08
ER
09
8 5
8 6
87
3 0
4
ER10
2
1
5
3
4
2
1
5
3
4
2
1
5
3
ER04
4
ER02
2
1
5
3
4
2
1
5
3
ER01
ER07
4
2
1
5
3
1
2
3
4
11
12
13
14
15
16
5
6
7
8
9
10
EF0
8
EF0
7
EF2
7
EF2
6
EF2
2
EF2
9
EF
0
3
EF
0
6
EF
0
9
EF2
5
EF1
7
EF1
6
EF1
5
EF
3
5
EF2
1
EF1
4
EF
01
EF
02
EF
04
EF
10
EF
1
1
EF1
8
EF2
4
8 6
Standard Value
Test Items
Specified Value
No
Refer to 2.2.7.20 DTC P0117 P0118 for coolant
temperature sensor or circuit malfunction.
Yes
No
559
High- or Low-Speed Relay 2 (86)-EM01(17)
Less than 1 Ω
Resistance Between High- or Low-Speed Relay
2 (86) and A Reliable Ground
10 kΩ or higher
Confirm whether the resistance conforms to standard value.
4
Inspect ECM working circuit.
(a) Inspect if ECM power circuit is normal.
(b) Inspect if ECM ground is normal.
5 Replace
ECM
6 Troubleshooting
Next
No
Repair the faulty part.
Yes
No
Repair the short to ground fault between the high- or
low-speed relay 2 socket #86 and ECM wire harness
connector EM01 terminal #17.
Yes
560
2.8.7.9 Thermostat Diagnostic
1
Dismantle the thermostat, see “2.8.8.4 Replacement of Thermostat”
2
Soak the thermostat in water and heat the water.
A. Inspect the thermostat switching on
temperature.
Standard value :82 (179 . 6 )
℃
℉
Is the thermostat switching on temperature
normal?
FE02-7814b
3
Inspect the thermostat valve lift range.
Standard valve lift:
Be 10 mm (0.39 in.) or more at 95
℃
(203°F)
Confirm whether the valve lift is normal.
A
FE02-7813b
No
Replace the thermostat, refer to 2.8.8.4
Replacement of Thermostat
Yes
No
Replace the thermostat, refer to 2.8.8.4
Replacement of Thermostat
Yes
Next
561
4
Inspect whether the thermostat is completely switched off at low temperature.
When the thermostat temperature is lower than 77 (171
℃
°F), Inspect whether the valve is
completely switched off.
5 Thermostat
is
normal.
No
Replace the thermostat, refer to 2.8.8.4
Replacement of Thermostat
Yes
562
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст