Geely Emgrand X7. Manual part — 210
Geely Emgrand X7. Manual part - 210
Step 4
Test sensor ECM internal low reference circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the intake camshaft
position sensor wiring harness
connector EN15.
(c) Rotated ignition switch to ON
position .
(d) Measure resistance between the
intake camshaft position sensor
wiring harness connector EN15
terminal B and reliable ground.
Standard Resistance: Less than 3 Ω
(e) Connect the intake camshaft
position sensor wiring harness
connector EN15.
NL02-2123b
A
B
C
EN15 凸轮轴位置传感器线束连接器
B
Is the value specified value?
Step 5
Refer to 2.10.7.1 “Replacement of Camshaft Position Sensor” to replace the intake
camshaft position sensor.
Step 6
Inspect the sensor 5 V reference voltage circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the intake camshaft
position sensor wiring harness
connector EN15.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between
intake camshaft position sensor
wire harness connector EM15
terminal C and ECM wire
harness connector EM01 terminal
70. Inspect whether there is
short-circuit situation.
NL02-2122b
A
B
C
EN15 凸轮轴位置传感器线束连接器
C
Next
Go to step 12
No
Go to step 8
Yes
EN15 camshaft position sensor harness
connector
EN15 camshaft position sensor harness
connector
839
(e)
Measure voltage between
camshaft position sensor harness
connector EN15 terminal No.C
and a reliable ground. Inspect
whether the circuit is short to
power supply.
(f)
Measure voltage between
camshaft position sensor harness
connector EN15 terminal No.C
and a reliable ground. Inspect
whether the circuit is open to
power supply.
NL02-2125b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
70
Test Items
Standard Value
EN15(C)-EN01(70) resistance
Less than 1 Ω
EN15(C)-reliable grounding resistance
10 kΩ or higher
EN15(C)-reliable grounding voltage
0V
Execute next step as per normal.
Step 7
Inspect Sensor Signal Circuit
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the intake camshaft
position sensor wiring harness
connector EN15.
(c)Disconnect ECM harness connector
EN01.
(d)
Measure resistance between
intake camshaft position sensor
wire harness connector EM15
terminal A and ECM wire harness
connector EM01 terminal 77.
Inspect whether there is
short-circuit situation.
NL02-2124b
A
B
C
EN15 凸轮轴位置传感器线束连接器
A
Next
Repair the faulty part. Go to step
EN01 engine control module harness
connector
EN15 camshaft position sensor harness
connector
840
(e)
Measure voltage between
camshaft position sensor harness
connector EN15 terminal No.A
and a reliable ground. Inspect
whether the circuit is short to
power supply.
(f)
Measure voltage between
camshaft position sensor harness
connector EN15 terminal No.A
and a reliable ground. Inspect
whether the circuit is open to
power supply.
NL02-2126b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58 57 56 55 54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
77
Test Items
Standard Value
EN15(A)-EN01(77) resistance
Less than 1 Ω
EN15(A)-reliable grounding resistance
10 kΩ or higher
EN15(A)-reliable grounding voltage
0V
Are the values specified values?
Step 8
Inspect sensor ECM internal low reference circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the intake camshaft
position sensor wiring harness
connector EN15.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between
intake camshaft position sensor
wire harness connector EM15
terminal B and ECM wire
harness connector EM01 terminal
74. Inspect whether there is
short-circuit situation.
NL02-2123b
A
B
C
EN15 凸轮轴位置传感器线束连接器
B
No
Repair the faulty part. Go to step 12
Yes
EN01 engine control module harness
connector
EN15 camshaft position sensor harness
connector
841
(e) Measure resistance between
intake camshaft position sensor
wire harness connector EN15
terminal B and reliable
grounding. Inspect whether there
is short-circuit situation.
NL02-2127b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
74
Test Items
Standard Value
EN15(B)-EN01(18) resistance
Less than 1 Ω
EN15(B)-reliable grounding voltage
0V
Execute next step as per normal.
Step 9
Inspect whether the intake camshaft signal plate is normal.
Step 10
Inspect the ECM Power Supply Circuits.
(a) Inspect whether ECM power supply circuit is normal.
(b) Inspect whether ECM ground circuit is normal.
Step 11
Replace ECM
Step 12
Use scan tool to confirm whether the DTC Code is stored again.
Next
No
Repair the faulty part.
Yes
No
Repair the faulty part.
Yes
Next
EN01 engine control module harness
connector
842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст