Geely Emgrand X7. Manual part — 191
Geely Emgrand X7. Manual part - 191
Is voltage the specified value?
Step 9
Measure pre-catalytic oxygen sensor ground circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the front oxygen
sensor harness connector EN02.
(c) Rotated ignition switch to ON
position .
(d) Measure resistance between front
oxygen sensor EN02 terminal A
and a reliable ground.
Standard Resistance: Less than 1 Ω
(e) Connect the front oxygen sensor
harness connector EN02.
NL02-2059b
A
B
C
D
EN02 前氧传感器线束连接器
A
Is resistance the specified value?
Step 10
Refer to 2.4.6.2 “Replacement of Front Oxygen Sensor” to replace the front oxygen
sensor
Step 11
Inspect the front oxygen sensor signal circuit.
No
Go to step 12
Yes
No
Go to step 11
Yes
Next
Go to step 15
EN02 front oxygen sensor harness
connector
763
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the front oxygen
sensor harness connector EN02.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between front
oxygen sensor wiring harness
connector EN02 terminal B and
ECM harness connector terminal
No.47. Inspect whether the
circuit is open. Otherwise, repair
the faulty part.
NL02-2058b
A
B
C
D
EN02 前氧传感器线束连接器
B
(e) Measure resistance between front oxygen sensor wiring harness connector EN02 terminal B
and a reliable ground. Inspect whether the circuit is short to ground. otherwise, repair the
faulty part.
(f) Measure voltage between front oxygen sensor wiring harness connector EN02 terminal B and
a reliable ground. Inspect whether the circuit is short to power supply. Otherwise, repair the
faulty part.
NL02-2060b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
47
Test Items
Standard Value
EN02(B)-EN01(47)Resistance value
Less than 1 Ω
EN02(B)-reliable grounding resistance value
10 kΩ or higher
EN02(B)-Reliable grounding voltage value
0V
Step 12
Inspect the front oxygen sensor ground circuit.
Normal
Go to step 15
EN02 front oxygen sensor harness
connector
EN01Engine control module harness
connector
764
(a) Rotated ignition switch to OFF
position .
(b) Disconnect the front oxygen
sensor harness connector EN02.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between front
oxygen sensor wiring harness
connector EN02 terminal A and
ECM harness connector terminal
No.73. Inspect whether the
circuit is open. otherwise, repair
the faulty part.
NL02-2059b
A
B
C
D
EN02 前氧传感器线束连接器
A
(e) Measure resistance between front oxygen sensor wiring harness connector EN02 terminal A
and a reliable ground. Inspect whether the circuit is short to ground. otherwise, repair the
faulty part.
(f) Measure voltage between front oxygen sensor wiring harness connector EN05 terminal A and
a reliable ground. Inspect whether the circuit is short to power supply. otherwise, repair the
faulty part.
NL02-2061b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
73
Test Items
Standard Value
EN02(A)-EN01(73)Resistance value
Less than 1 Ω
EN02(A)-reliable grounding resistance value
10 kΩ or higher
EN02(A)-Reliable grounding voltage value
0V
Execute next step as per normal.
Step 13
Inspect the ECM Power Supply Circuits.
Yes
EN02Front oxygen sensor harness
connector
EN01Engine control module harness
connector
765
(a) Inspect whether ECM power supply circuit is normal.
(b) Inspect whether ECM ground circuit is normal.
Step 14
Replace ECM
(a) Refer to 2.12.8.1 Replacement of Engine Control Module to Replace ECM.
(b) Carry out the crankshaft position sensor learning, refer to 2.12.7.11 “Crankshaft Position
Sensor (CKP) Learning.
Step 15
Use fault diagnosis tester to confirm if DTC is stored again .
(a) Connect the fault diagnosis tester to the diagnostic interface.
(b) Turn ignition switch to ON position.
(c) Clear DTC code.
(d) Start and run the engine at idle speed to warm up the engine for at least 5 min.
(e) test the vehicle on the road for at least 10 min.
(f) Read control system DTC code again to confirm that the system has no DTC code.
Step 16
Troubleshooting
5. Maintenance
guide
:
Refer to 2.4.6.1 “Replacement of Front Oxygen Sensor” to replace the front oxygen sensor
No
Refer to 2.12.7.3 Intermittent Fault
Inspection for intermittent fault.
Yes
No
Repair the faulty part.
Yes
766
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст