Geely Emgrand X7. Manual part — 227
Geely Emgrand X7. Manual part - 227
3. Circuit
figure
NL02-2159b
5 IP24
8 IP24
7 IP24
46 EN01
75 EN01
IP12
7
芯片防盗模块
诊断接口
ECM
IMMOREQ
KW2000
R-LINE
W-LINE
K-LINE
Gr
/P
4. Diagnostic
Steps:
Refer to 2.5.7.17 Engine Anti-theft Warning Lamp Flashing, Vehicle Can Not Start
5. Maintenance
guide
:
Refer to 2.5.7 “Diagnostic Information and Procedures” of the engine anti-theft system to repair
the anti-theft system.
Chip anti-theft
module
Diagnostics
interface
907
2.12.7.56 DTC P0831 P0832
1. DTC
description:
DTC P0831
Clutch switch circuit at low voltage
DTC P0832
Clutch switch circuit at high voltage
When clutch switch is short to the ground or open (at high voltage), after several times of
acceleration from starting-up to >52 Km/h, or deceleration from >52 Km/h to <3 Km/h, the DTC
codes appear with the engine running stably, and the vehicle can be driven.
2. Conditions For Setting DTC and The Fault Location:
DTC
Code
DTC Detection
Strategy
Conditions For Setting The DTC
(Control Strategy)
Fault Locations
P0831
1. Clutch switch signal disconnect or
high voltage
2. Acceleration from starting-up to
>52 Km/h, or deceleration from >52
Km/h to <3 Km/h.
3. DTC codes appear after repeatedly
braking.
P0832
ECM receives the
clutch signal
1. Clutch switch signal short.
2. Acceleration from starting-up to
>52 Km/h, or deceleration from >52
Km/h to <3 Km/h.
3. DTC codes appear after repeatedly
braking.
1. Clutch
Switch
Circuit
2. Clutch
Switch
3. ECM
908
3. Circuit
figure
NL02-2306b
10
A
IF0
3
ECM
35
EN01 CS
2
IP60
1
IP60
R
离合器开关
4. Diagnostic
Steps:
Notes:
Before carrying out this diagnosis steps, observe the data list on fault diagnosis tester and
analyze the accuracy of the data, as these will help with quick diagnosis.
1
Inspect for other DTC Codes other than P0831 and P0832.
A. Connect fault diagnosis tester to the vehicle diagnostic interface.
B. Rotated ignition switch to ON position.
C. Press the power button of fault diagnosis tester.
D. Select the following menu items: Engine/Read DTC codes.
E. Read DTC codes.
Results
DTC Codes shown
To Step
DTC P0831 P0832
Yes
DTC Code Other Than DTC P0831 P0832
No
Yes
Refer to 2. 12.6.11 DTC Chapter Index.
No
Clutch switch
909
2
Is the clutch switch working correctly?
Note: When the clutch switch fails, during emergent acceleration and deceleration, the vehicle
will vibrate seriously and even push forward.
3
Inspect the continuity between clutch switch wiring harness connector IP60 and ECM
harness connector EN01.
A. rotated ignition switch to OFF
position.
B.
Disconnect ECM harness
connector EN01.
C. Press the brake pedal.
D. Measure ECM harness connector
EN01 terminal No.34 resistance.
Standard Resistance: Less than 3 Ω
Confirm whether the resistance is
normal.
NL02-2307b
IP60 离合器开关线束连接器
1
2
4
Repair the circuit between clutch switch wiring harness connector IP60 and ECM
harness connector EN01.
A. Repair the circuit between clutch switch wiring harness connector IP60 and ECM harness
connector EN01.
B. Confirm the repair is completed.
5
Is the clutch switch working correctly?
Note: When the clutch switch fails, during emergent acceleration and deceleration, the vehicle
will vibrate seriously and even push forward.
Next
Yes
Refer to 2.12.8.1 Replacement of Engine
Control Module to replace ECM.
No
Yes
Refer to 2.12.7.3 Intermittent Fault
Inspection for intermittent fault.
No
IP60 Clutch switchharness connector
910
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст