Geely Emgrand X7. Manual part — 151
Geely Emgrand X7. Manual part - 151
2.9.8.3 Replacement of Oil Pan
Dismantlement Procedure
Warning: Refer to "Warning on
Battery Disconnection" in
"Warnings and Precautions".
Warning: Refer to Warning on
Vehicle Lifting and Jacking in
Warnings and Precautions.
1. Disconnect the battery negative
electrode cable. Refer to 2.12.6.1
Battery Disconnection.
2. Lifting and Jacking the Vehicle
3. Loosen oil drain plug of engine
oil pan, and drain lubricating oil
from engine oil pan.
FE02-0372b
4. Dismantle the fixing bolts and
nuts of oil pan.
5. Dismantle the oil pan from the
crankcase.
GC02-0111c
Installation Procedure:
1. Inspect and clean the oil strainer
before installing the oil pan.
2. Clean mating surface between oil
pa n and cylinder block.
3. Apply sealant uniformly on new
oil pan.
GC02-0112c
603
4. Install the oil pan and tighten the
fourteen fixing bolts and nuts
according to the sequence as
shown in the figure.
5. Install oil pan purge plug screw
gasket and purge plug screw, and
tighten the purge plug screw.
Torque :33~37N . m(Metric) 25~
28b-ft(English system)
6. Install negative cable of battery.
14
12
10
8
6
4
2
13
11
9
7
5
3
1
GC02-0113c
604
Torque: 7~10N.m or 5~8lb-ft
2.9.8.4 Replacement of Oil Filter
Dismantlement Procedure
Warning: Refer to "Warning on
Battery Disconnection" in
"Warnings and Precautions".
Warning: Refer to Warning on
Vehicle Lifting and Jacking in
Warnings and Precautions.
1. Disconnect the battery negative
electrode cable. Refer to 2.12.6.1
Battery Disconnection.
2. Lifting
and
Jacking
Vehicle
3. Release the engine oil discharge
bolt of oil pan, discharge the
lubrication oil from the
crankcase.
FE02-0372b
4. Dismantle the oil filter.
5. Dismantle the oil filter adapter.
GC02-0115c
Installation Procedure:
1. Install the oil filter adapter.
Torque :27~33N . m(Metric) 19~24b-ft(English system)
2. Install the oil filter
3. Lower
the
vehicle.
4. Fill the engine lubrication oil.
5. Connect battery negative cable.
605
2.9.8.5 Replacement of Piston Oil Injector Components
Dismantlement Procedure
Warning: Refer to "Warning on
Battery Disconnection" in
"Warnings and Precautions".
1. Dismantle the engine. Refer to
2.6.8.13 Replacement of Engine.
2. Refer to 2.6.8.14 Replacement of
Cylinder Hood Assembly to
dismantle the cylinder hood.
3. Dismantle the crank, refer to the
2.6.8.18 "Replacement of
Crankshaft"
4. Dismantle the fixing bolts of
piston fuel injector components.
5. Dismantle the piston fuel injector
components.
GC02-0116c
Installation Procedure:
1. Install the piston injector
components into the cylinder
body piston injector orifice.
2. Install the hexagon socket cap
head screws.
Torque :6 ~ 8 N . m(Metric)4 ~ 6
b-ft(English system)
3. Install
the
crankshaft.
4. Install the cylinder hood.
5. Install the engine assembly.
GC02-0116c
606
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст