Geely Emgrand X7. Manual part — 175
Geely Emgrand X7. Manual part - 175
P0633
Anti-theft Does Not Learn Malfunction
C
B0010
Collision Fuel Cut-off Reasonability Malfunction
C
U0167
No response of anti-theft device
C
U0426
Anti-theft Device Authentication Malfunction
C
699
2.2.7.8 DTC Fail-Safe List
DTC Code
DTC Code Diagnostic
Information
Fail-Safe Mode
Restore
Conditions
P0068
Electronic Throttle Air Flow
Error
Electronic Throttle
Position Sensor #1 Circuit
Low Voltage
Electronic
Throttle Position
Sensor #1 Circuit
Low Voltage
P0122
Electronic Throttle Position
Sensor #1 Circuit Low Voltage
P0123
Electronic Throttle Position
Sensor #1 Circuit Low Voltage
P0222
Electronic Throttle Position
Sensor #1 Circuit Low Voltage
P0223
Electronic Throttle Position
Sensor #1 Circuit Low Voltage
Use TPS signal value that
is not expired. If both
TPS1 and TPS2 fail, the
system will enter the
Engine Power
Management mode, while
reporting P2106, P2110
fault; VCP is inoperative
No malfunction
condition is
detected.
P0571
The switch state of the brake
lamp is not changed when
braking.
At this time, if the system
enters Restrictions on
Engine Performance
mode, the system enters
the Mandatory Engine
Idling mode.
No malfunction
condition is
detected.
P0606
ECM Processor Malfunction
System enters Mandatory
Engine Shutdown mode,
the engine can not start
and the system will report
P2105.
Fault
Next key cycle,
no malfunction
condition
detected.
P060A
ECM Programming Errors
Engine Can Not Start
Next key cycle,
no malfunction
condition
detected.
P0641
ETC Reference Voltage #A
Amplitude Fault
The system enters the
mode of engine power
management and submits
to P0122, P0223 and
P2106 at the same time.
P2110 fault ;VCP do not
work
Next key cycle,
no malfunction
condition
detected.
P0651
ETC Reference Voltage #B
Amplitude Fault
System enters Restrictions
on Engine Performance
model, while reporting
P2106 fault; VCP is
inoperative
No malfunction
condition is
detected.
P1516
ETC-Driver Steady-State
Diagnostic Error
The system enters the
mode of engine power
Next key cycle,
no malfunction
700
management.
At some time, commited
P2106、P2110 fault;
VCP Inoperation
condition
detected.
P2101
ETC-Driver Second-Order
Diagnostic Error
System enters Engine
Power Management mode,
while reporting P2106 and
P2110 fault; VCP is
inoperative
Next key cycle,
no malfunction
condition
detected.
P2104
Mandatory Engine Idling
P2105
Mandatory Engine Shutdown
P2106
Restrictions on Engine
Performance
P2110
Engine Power Management
Refer to ETC TPS, APS
relevant diagnosis
Refer to ETC
TPS, APS
relevant diagnosis
P2119
Electronic Throttle Return
Malfunction
None
No malfunction
condition is
detected.
P2122
Electronic Acceleration Pedal
Position Sensor #1 Circuit Low
Voltage
P2123
Electronic Acceleration Pedal
Position Sensor #1 Circuit
High Voltage
P2127
Electronic Acceleration Pedal
Position Sensor #2 Circuit Low
Voltage
P2128
Electronic Acceleration Pedal
Position Sensor #2 Circuit
High Voltage
(1) Single APS
malfunction, the system
enters Restrictions on
Engine Performance
mode, while reporting
P2106 fault
(2) If both APS1 and
APS2 fail, the system
enters Mandatory Engine
Idling mode, while
reporting P2104 fault
(3) VCP Inoperation
In the next Key
Cycle, ECM
detects
invalidation.
Validation
conditions
P2135
Related fault of Electric
throttle valve position
sensor1# . 2#
The system enters the
mode of engine
performance limit.
Meanwhile, report P2106
fault; the VCP does not
work.
No malfunction
condition is
detected.
P2138
Electronic Acceleration Pedal
Position Sensor #1 and #2
Related Malfunctions
System enters Restrictions
on Engine Performance
model, while reporting
P2106 fault; VCP is
inoperative
No malfunction
condition is
detected.
P0011
Intake VCP Phase Response
Lag Behind
None
No malfunction
condition is
detected.
701
P0012
Intake VCP Camshaft Phase
Error is Big
VCP Inoperation
No malfunction
condition is
detected.
P0016
Intake VCP Camshaft Gear
Learn Bias Out of Range
OCV Cleaning Function
Enabled; VCR Inoperative
No malfunction
condition is
detected.
P0026
Intake VCP Hydraulic Control
Valve Clinch
OCV Cleaning Function
Enabled; If cleaning
failed, VCR is inoperative
No malfunction
condition is
detected.
P0076
Intake VCP Hydraulic Control
Valve Coil Low Voltage or
Open Circuit
VCP Inoperation
No malfunction
condition is
detected.
P0077
Intake VCP Hydraulic Control
Valve Coil High Voltage
VCP Inoperation
Next key cycle,
no malfunction
condition
detected.
P0340
Intake VCP Camshaft Position
Sensor Status Diagnosis
VCP Inoperation, Ignition
Angle
No malfunction
condition is
detected.
P0341
Intake VCP Target Wheel
Diagnosis
VCP Inoperation, Ignition
Angle
No malfunction
condition is
detected.
P0106
Intake Pressure/Throttle
Position Fault
(1) When Key is in ON
position, the system will
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
Manifold pressure value
No malfunction
condition is
detected.
P0107
Manifold air pressure sensor
circuit has low voltage or is
open
(1) When Key is in ON
position, the system will
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
Manifold pressure value
No malfunction
condition is
detected.
P0108
Intake Air Pressure Sensor
Circuit High Voltage
(1) When Key is in ON
position, the system will
intake air in default form.
Manifold pressure value of
100 kPa
(2) When the engine is
running, the system uses
No malfunction
condition is
detected.
702
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст