Geely Emgrand X7. Manual part — 75
Geely Emgrand X7. Manual part - 75
2.2.7.49 DTC P2104 P2105 P2106 P2110
1. DTC
description:
DTC P2104
Mandatory Engine Idling
DTC P2105
Forced engine stopping
DTC P2106
Restrictions On Engine Performance
DTC P2110
Engine Power Management
When the intake system or throttle body valve air floe control have faults, ETC system can not
reliably use the throttle to control engine power.
2. DTC Code Set Up and Removal Conditions:
DTC Code
DTC Detection
Strategy
Set(Control Strategy) Conditions Fault
Locations
P2104
Protected mandatory
idle
When the sensor of the throttle,
acceleration pedal or brake has
certain fault, it will be forced into
the idle mode, and determined as
fault.
P2105
Fault Protection
Mandatory Shutdown
When the sensor of the acceleration
pedal, brake or ECM has certain
fault, it will be forced into engine
stalling and determined as fault.
P2106
Fault Protection
Limits
When the sensor of the throttle or
acceleration pedal has certain fault,
it will be forced into the
performance limited mode, and
determined as fault.
P2110
Failsafe Power Limit
When the sensor of the throttle or
acceleration pedal has certain fault,
it will be forced into the power
manage mode, and determined as
fault.
——
3. Diagnostic
Steps:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and
analyze the accuracy of the data, as these will help with quick diagnosis.
1
Inspect whether there is any control system DTC code other than DTC P2104, P2105,
P2106 and P2110.
299
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic apparatus power supply
D. Select the following menu items: Engine/Read DTC codes.
E. Read DTC code
Results
DTC Codes Shown
To Step
DTC P2104 P2105 P2106 P2110
No
DTC code other than DTC P2104, P2105,
P2106, P2110
Yes
2
Use a fault diagnosis tester to confirm whether the DTC Code is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5 min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
3
Inspect the ECM Power Supply Circuits.
A. Inspect whether ECM power supply circuit is normal.
B. Inspect whether ECM ground circuit is normal.
4 Replace
ECM
A. Replaces
B. Refer to 2.2.7.11 Crankshaft Position Sensor (CKP) Learn to carry out the crankshaft position
sensor learn.
Next
No
Repair the faulty part. Go to step 5
Yes
Yes
Diagnostic
No
Yes
2.2.7.14 DTC Chapter Index
No
300
5
Use a fault diagnosis tester to confirm whether the DTC Code is stored again.
A. Connect fault diagnosis tester to the data link connector.
B. Rotated ignition switch to ON position
C. Clear DTC code.
D. Start and run the engine at idle speed to warm up the engine for at least 5 min.
E. Read control system DTC code again to confirm that the system has no DTC code exported.
6 Troubleshooting
5. Maintenance
guide
Replace ECM. Refer to 2.2.8.1 Replacement of Engine Control Module.
No
Refer to 2.2.7.3 Intermittent Fault
Inspection for intermittent fault.
Yes
301
2.2.7.50 DTC P2119
1. DTC
description:
DTC P2119
Electronic Throttle Return Malfunction
After the ignition switch is switched off, electronic throttle stays at the initial angle of 14.5
degrees. If the ignition switch is off, the throttle is always off, the DTC code may be recorded it
may be accompanied by the engine difficult to start and so on. 2.Conditions for Setting DTC and
the Fault Location:
DTC Code
DTC Detection
Strategy
Set(Control Strategy)
Conditions
Fault Locations
P2119
Electronic Throttle
Return Malfunction
1. Ignition Switch OFF for
several times.
2. If throttle can't reach
requirement, conduct return
test. Proper opening
1. Electronic
Throttle
Body Dirty
2. Electronic
Throttle
Body Mechanical
Malfunction
3. Diagnostic
Steps:
1
Inspect whether there is other ETC system related DTC codes?
A. Connect fault diagnosis tester to the vehicle diagnostic interface.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic apparatus power supply
D. Read DTC code
Results
DTC Codes Shown
To Step
Only P2119
Yes
DTC Code Other Than P2119
No
A. Refer to 2.6.8.5 Replacement of Electrical Throttle Body Assembly to dismantle the throttle
body.
B. Clean electronic throttle body.
3
Use fault diagnosis tester to confirm if DTC is stored again .
A. Connect fault diagnosis tester to the data link connector.
2 Clean
Electronic
Throttle
Body
Next
No
Refer to 2. 12.7.14 DTC Chapter Index.
Yes
302
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст