Geely Emgrand X7. Manual part — 480
Geely Emgrand X7. Manual part - 480
10.2.4.9 DTC B1212
Fault diagnosis code Descriptions
B1212
The key hole illumination lamp is shorted to battery fault.
Circuit diagram:
5 IP43
IP25
1
2 IP43
IP25
2
IP43
4
IP43
3
15A
IF
06
ACC
IP49
2
BCM
KEY LIGHT
防盗天线
芯片防盗模块
NL11-3219b
Diagnostic Steps:
1
Inspect whether there is any DTC Code other than B1212.
(a) Inspect whether there is any DTC Code other than B1212.
2
Inspect the voltage of the key buckle illuminating lamp.
Yes
Go to
DTC list in 10.2.4.2
and repair according to
trouble codes.
No
Immobilizer
antenna
Chip anti-theft
module
1919
(a) Turn the ignition switch to ON position.
(b) Unplug fuse IF06.
(b) Measure anti-theft antenna harness connector
IP43 terminal 4 voltage.
Voltage standard value :0V
Confirm if the voltage conforms to standard value.
NL11-3220b
1
2
3
4 5 6
IP43防盗天线线束连接器
3
Replace electronic Anti-theft coil.
(a) Inspect whether dome lamp bulb is burned out.
Confirm the completion of repair.
4
The system is normal.
No
Repair or replace the harness.
Yes
Next
IP43Immobilizer antenna harness
connector
1920
10.2.4.10 DTC B1216
Fault diagnosis code Descriptions
B1216
A headlamp relay controls short circuit until a battery faults.
Circuit diagram:
CA18
6 CA12
5 CA12
16 IP42
13 IP42 14 IP42 6 IP42
5 IP49
40 IP50
2 IP05
1 IP05
3 IP05
26 IP50 7 IP50
近光灯
继电器
灯光
组合
开关
右前
组合
大灯
左前
组合
大灯
远光
近光
远光
近光
阳光传感器
6 CA18
5
OFF
位置灯
近光
远光
超车灯
自动
7
13
8
14
16
6
5
2
1
3
+B
IG1
ER01
15
A
EF
26
10
A
IF
25
BCM
NL11-3242b
Diagnostic Steps:
1
Inspect whether there is any DTC Code other than B1216.
(a) Inspect whether there is any DTC Code other than B1216.
2
Inspect the voltage of the terminal 5 of BCM wire harness
connector IP49.
Yes
Go to
DTC list in 10.2.4.2
and repair according to
trouble codes.
No
Solar sensor
Low beam
lamp relay
ER01
Position lamp
Low beam
High beam
Overtake lamp
Auto
Lighting
combination
switch
Left front co
mbinati
on
headlamp
Right front
combinatio
n headla
mp
High beam
low beam
High beam
low beam
1921
(a) Turn on lower-beam lamp.
(b) Measure voltage of BCM wire harness
connector IP49 terminal 5.
Voltage standard value :0V
Confirm if the voltage conforms to standard
value.
NL11-3243b
1
2 3
4 5 6
7
8 9 10
11 12 13 14 15 16 17 18 19 20
IP49BCM线束连接器
3
Replace the BCM
(a) Replace BCM and refer to
Replacement of BCM in 11.8.8.1
.
Confirm the completion of repair.
4
The system is normal.
No
Repair or replace the harness.
Yes
Next
IP49BCMharness connector
1922
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст