Geely Emgrand X7. Manual part — 471
Geely Emgrand X7. Manual part - 471
9.3.7.10 Replacement of Front Seat Belt Height Regulator
Dismantlement Procedure
1.
For dismantling of middle column upper
trimming plate, refer to 12.9.1.3 Replacement of
middle column trimming plate.
2. Remove the top fixing nut on the center pillar for
the front seat belt.
NL09-0049b
3. Dismantle fixing bolt of safety belt height adjuster
of front row seat.
NL09-0062b
Installation Procedure:
1. Install front row seat safety belt height adjuster
and tighten fixing bolt.
Torque: 35Nm (Metric) 25. 9lb-ft(English system)
NL09-0063b
1883
2. Install and tighten upper fixing nut of middle
column of front seat safety belt.
Torque: 45Nm (Metric) 33. 3lb-ft(English system)
3. Install the middle column upper trimming plate.
NL09-0051b
1884
10.1 Warning and precaution . . . . . . . 1886
10.1.1 Warning and precaution . . . . . . . . 1886
10.2 Computer and integration system(JL4G18-E)
. . . . . . . . . . . . . . . . . . . .. 1887
10.2.1 Specifications . . . . . . . . . . . . 1887
10.2.1.1 Fastener specifications. . . . . . . ... 1887
10.2.2 Description and Operation . . . . . . . 1887
10.2.2.1 Description and operation.. . . . . . . 1887
10.2.3 Part position . . . . . . . . . . . ... 1889
10.2.3.1 BCM location plan. . . . . . . . . . 1889
10.2.4 Diagnostic information and steps . . . .. 1890
10.2.4.1 BCM Terminal List. . . . . . . . . 1890
10.2.4.2 Fault diagnostic code (DTC) table . . .. 1894
10.2.4.3 DTC B1201 B1202 . . . . . . . . . 1896
10.2.4.4 DTC B1203 B1204 . . . . . . . . . 1900
10.2.4.5 DTC B1205 B1206. . . . . . . . . 1903
10.2.4.6 DTC B1207 B1208. . . . . . . . . 1907
10.2.4.7 DTC B1209 B1210. . . . . . . . . 1911
10.2.4.8 DTC B1211 . . . . . . . . . . . . 1915
10.2.4.9 DTC B1212 . . . . . . . . . . . . 1919
10.2.4.10 DTC B1216. . . . . . . . . . . . .1921
10.2.4.11 DTC B1237. . . . . . . . . . . .. 1923
10.2.4.12 DTC B1213. . . . . . . . . . . .. 1926
10.2.4.13 DTC B1214. . . . . . . . . . . .. 1928
10.2.4.14 DTC B1215. . . . . . . . . . . .. 1930
10.2.4.15 DTC B1217. . . . . . . . . . . .. 1932
10.2.4.16 DTC B1218. . . . . . . . . . . .. 1935
10.2.4.17 DTC B1220. . . . . . . . . . . .. 1938
10.2.4.18 DTC B1222 . . . . . . . . . . .. 1941
10.2.4.19 DTC B1224 . . . . . . . . . . .. 1944
10.2.4.20 DTC B1236 . . . . . . . . . . 1945
10.2.4.21 DTC U1000 . . . . . . . . . . .. 1947
10.2.4.22 DTC U1004 . . . . . . . . . . .. 1949
10.2.4.23 DTC U1005 . . . . . . . . . . . .1951
10.2.5 Dismantle and install . . . . . . . . . 1953
10.2.5.1 BCM replacement. . . . . . . . . .. 1953
10.3 Computer integrated manufacturing
system(JLD-4G20/JLD-4G24) . . . . . . ... 1954
10.3.1 Specification . . . . . . . . . . . .. 1954
10.3.1.1 Fastener specifications . . . . . . ... 1954
10.3.2 Description and operation . . . . . . . 1955
10.3.2.1 Description and operation. . . . . ... 1955
10.3.3 Diagnostic information and steps . . . .. 1963
10.3.3.1 BCM Terminal List. . . . . . . . ... 1963
10.3.3.2 Fault Diagnosis Code (DTC) List. . . . .1970
10.3.3.3 DTC B1201 B1202. . . . . . . . . 1972
10.3.3.4 DTC B11B312. B11B312. . . . . . . 1978
10.3.3.5 DTC B11B312. B11B312 . . . . . .. 1983
10.3.3.6 DTC B11B512. B11B512 . . . . . .. 1986
10.3.3.7 DTC B11D214. B11D213. B11D212.
B11D312. B11D313. B11D314. . . . . . . .. 1989
10.3.3.8 U012187. U010087. U015187. U12501C.
U12511C. U015587 . . . . . . . . . . . . 1992
10.3.5 Dismantle and install . . . . . . . . . 1993
10.3.5.1 BCM replacement . . . . . . . . ... 1993
10.4 Programming and Setting. . . . . . . . 1994
10.4.1 Programming and Setting. . . . . . . . 1994
10.1 Warning and precaution
10.1.1 Warning and precaution
Warning on Battery Disconnection
Warning!
Unless directed, otherwise, the ignition and start switch must be in OFF or LOCK position, and all electrical loads
must be OFF before servicing any electrical component. Disconnect the negative battery cable if a tool or any
equipment easily comes in contact with an exposed electrical terminal. Failure to follow these precautions may
result in personal injury and/or damage to the vehicle or its components.
Road Test Warning
Warning!
Test a vehicle on the roads under safe conditions and obey all traffic laws. Do not attempt any operation that could
jeopardize vehicle control. Failure to obey these precautions will lead to serious personal injury and vehicle
damage.
Window Quick Down Warning
Warning!
Operate the power window switch when working inside the driver door. When operated, the Quick Up/Down
function allows the window to move very quickly without stopping, which could cause personal injury.
Ignition OFF When Disconnecting Battery Notice
Notes:
Always turn the ignition OFF when connecting or disconnecting battery cables, battery chargers or jumper cables.
Failing to do so may damage the control module or other electronic components.
Precautions on Power System Control Module and Electrostatic Discharge
Notes:
Do not touch the connector pins or soldered components on the circuit board in order to prevent possible
electrostatic discharge (ESD) damage to the ECM.
1886
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст