Geely Emgrand X7. Manual part — 389
Geely Emgrand X7. Manual part - 389
(g) Ignition switch turn to OFF.
(h). Measure the resistance between terminals No.3 / No.6 of connector IP01 and the body ground respectively
with a multimeter.
Standard Resistance: Less than 1 Ω
Confirm whether the measured value is accorded with the standard.
3
Check brake fluid fluid sensor .
A. Disconnect the harness connector of the brake fluid level sensor.
B. Measure the resistance between 2 terminals of the brake fluid level sensor with the universal meter.
Standard resistant value: infinity
C. Confirm if the resistance conforms to standard value.
4
Check brake fluid level sensor harness.
(a) Disconnect combination instrument harness
connector IP02.
(b) Use multimeter to measure resistance between
IP02 terminal 9 and CA20 terminal 1.
(c) Use multimeter to measure resistance between
CA20 terminal 2 and vehicle grounding.
Standard Resistance: Less than 1 Ω
Confirm if the resistance conforms to standard value.
NL06-1017b
IP02 组合仪表线束连接器2
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18
9
Replace brake fluid level sensor, refer to 6. 4. 5 .
7 brake fluid
Check fuse, repair or replace harness
Yes
No
Yes
No
IP02 combination instrument
harness connector2
1555
NL06-1018b
1
2
CA20 制动液液位传感器线束连接器
1
2
5
Replace combination instrument ,
(a) Replace the combination instrument and refer to 11.6.7.1 Replacement of Combination Instrument
Assembly.
(b) Confirm the repair is completed.
6
The system is normal.
Repair or replace the harness.
Yes
No
Next
CA20 brake fluid level fluid harness connector
1556
6.4.5 Dismantle and installation
6.4.5. 1 Brake master pump fluid reservoir replacement
Dismantle procedure
1. For dismantling of brake main pump, refer to
6.4.5.2 Replacement of brake main pump.
2. Take out connecting pin of brake main pump and
fluid reservoir, and dismantle fluid reservoir from
brake main pump, and replace its sealing
element.
NL06-0028b
Installation procedure:
1. Lubricate sealing element of fluid reservoir by
using clean brake fluid.
2. Install lubricated sealing element into brake main
pump.
3. Install fluid reservoir to brake main pump, and
install connecting pin.
4. Install brake main pump with fluid reservoir.
NL06-0029b
1557
6.4.5.2 Brake master pump replacement
Dismantle procedure
NL06-0030b
Warning!
Warning:
Refer to Warning for battery disconnection in warning
and precaution.
1. Disconnect the battery negative cable. refer to
2.11.8.1 battery cable disconnection/connection
procedures .
2. Discharge brake fluid
Notes:
See Important precaution brake fluid affected for
paint and electrical part in warnings and precaution .
3. Disconnect brake fluid level sensor harness
connector.
4. Release the clamp for the hose from the clutch
master cylinder to fluid reservoir and Take out
the hose from the fluid reservoir.
NL06-0031b
5. Remove nut 1 of the brake oil pipe connector.
6. Block the brake line opening to prevent the loss
of and contamination by the brake fluid.
7. Remove 2 Fixing Nuts 2 for the master brake
cylinder.
8. Dismantle the brake master cylinder with fluid
reservoir and place on a clean table.
2
2
1
1
NL06-0032b
1558
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст