Geely Emgrand X7. Manual part — 322
Geely Emgrand X7. Manual part - 322
8 Troubleshooting
5. Maintenance
guide:
Replace automatic transmission control module, refer to3.5.7.8 replace automatic transmission control module
Yes
No
Refer to 2.2.7.3 intermittent fault inspection for
intermittent fault.
1287
3.5.7.9 P0707 P0708
1. DTC
description:
DTC P0707 Shift level position sensor (gear switch): low voltage
DTC P0708 Shift level position sensor (gear switch): high voltage
The gear switch assembly provides gear shifting position data to the transmission control unit (TCU). When the
gear switch is not in position P or N, the system will prohibit the operation of the starter. When putting into the
gear R, the backup lamp circuit accesses. The shift switch has independent circuit with respect to the above
function. The above function can only normally operate after the circuit is correctly connected with the TCU.
The transmission control unit provides a 5V reference signal to the gear position control circuit (gear switch) to
measure the voltage of the circuit and thus determine the position in which the gear is in. The resistance value in
different shift positions is different.
2. Conditions for setting DTC and the fault position:
DTC code
DTC detection strategy
Conditions for setting the DTC
(Control strategy)
Fault position s
P0707
Shift level position sensor
(gear switch) gives a
grounding short circuit
indicated value.
P0708
The transmission oil
temperature sensor
provides an open circuit
indicative value.
Ignition switch is in ON position
1.Gears switch
2. Gears
switch
circuit
3. TCU
3. Circuit
sketch
1288
T
C
U
电磁阀
换挡器
档位开关
LEVER
REVERSE
START
VBS5
VBS6
VBS7
V
BS8
VBS9
VBS1
0
O
n
O
ff
1
O
n
O
ff
2
O
n
O
ff
3
O
n
O
ff
4
EMM
INPUT
SHAFT
SPEE
D
SENSOR
OU
TPUT
SHAFT
t
SPE
ED
SENSOR
25
26
10
11
9
8
13
12
24
23
22
21
20
7
6
5
4
3
2
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
J-4
1
18
8
1
3
2
12
14
4
11
12
9
10
15
2
1
4
3
6
5
7
7
J-5
5
16
17
J-5
4
J-5
1
J-5
6
J-5
2
J-5
3
4
11
10
10
15
3
CAN H
启动继电器
倒车信号
输出
主继电器
JF-1
IG2
JB-2
CAN L
10
20
J-3
J-1
J-3
J-2
J-2
J-3
J-3
J-3
J-1
8
J-3
J-3
J-3
J-3
J-3
J-3
J-3
J-3
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
J-1
IF36
NL03-2005c
4. Diagnostic
procedures:
Note: Before carrying out this diagnosis step, observe the data list on fault diagnosis tester and analyze the
accuracy of the data, as these will help with quick diagnosis.
1
Read the fault code again after clearing away the fault code to check if fault codes, except DTC
P0707 and P0708 exist in the control system.
A. Connect fault diagnosis tester to the datalink connector.
B. Rotated ignition switch to ON position
C. Switch on fault diagnostic device power supply
D. Clear DTC code.
E. Reset reading fault code, and check if DTCs meet setting condition of fault code in current
DTC Codes Shown
To step
DTC P0707, P0708
Yes
DTC except for DTC P0707, P0708
No
Gears switch
Main relay
JF-1
Reverse output
signal
Start relay JB-2
Shifter
Electromagnetic
valve
1289
2
Detect the resistance of shift level position sensor (gear switch) under the state of each gear.
A. Turn the ignition switch to the OFF position.
B. Change the shift gear to the “P”, “R”, “N”, “D”
and “M” positions in order to measure the
resistance between Terminals 4 and 5 of the
harness connector J-5 of the gear switch.
档位开关线束连接器
J-4
1
2
3
4
5
6
SL03-0037c
Results
Gears
Test Items
Standard resistant value
P J-5(4)—J-5(5)
16.789
kΩ±8%
R J-5(4)—J-5(5)
8.953
kΩ±8%
N J-5(4)—J-5(5)
5.036
kΩ±8%
D J-5(4)—J-5(5)
2.686
kΩ±8%
M(manual mode )
J-5(4)—J-5(5)
1.119 kΩ±8%
Does it conform to the standard value?
Notes: if reset the step after replace gears switch, it meet standard valure, otherwise,replace Automatic
transmission assembly,
3
Detect the signal circuit of shift level position sensor (gear switch)
A. rotated ignition switch to OFF position.
B. Disconnect the harness connector J-5 of the gear switch.
No
Yes
Refer to3.4.7.6 fault diagnosis code (DTC) chapter
index
No
Yes
Replace gears switch
Gears switch harness connectorJ-4
1290
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст