Geely Emgrand X7. Manual part — 202
Geely Emgrand X7. Manual part - 202
NL02-2088b
A
B
EN13 3缸燃油喷射器线束连接器
A
Standard Resistance
Test Items
Standard Value
EN13(b) and main relay No,30 terminal
Less than 1 Ω
EN13(b) and reliable grounding
10 kΩ or higher
(f) Install the engine main relay.
(g) Connect cylinder 3 fuel injector wire harness connector EN13.
Exclude the fuel injector power supply circuit fault.
Step 6
Inspect the Cylinder #3 fuel injector control circuit.
(a) Rotated ignition switch to OFF
position .
(b) Disconnect cylinder No.3 fuel
injector harness connector EN13.
(c)
Disconnect ECM harness
connector EN01.
(d) Measure resistance between
cylinder No.3 fuel injector wiring
harness connector EN13 terminal
No.A and ECM harness
connector terminal No.7. Inspect
whether the circuit is open.
Otherwise, repair the faulty part.
NL02-2091b
A
B
EN13 3缸燃油喷射器线束连接器
B
Go to step 9
Next
EN13 3rd cylinderfuel injector
EN13 3rd cylinderfuel injector
807
(e) Measure resistance between
cylinder No.3 fuel injector wiring
harness connector EM13 terminal
No.A and a reliable ground.
Inspect whether the circuit is
short to ground. Otherwise,
repair the faulty part.
(f)
Measure voltage between
cylinder No.3 fuel injector
harness connector EN13 terminal
No.A and a reliable ground.
Inspect whether the circuit is
short to power supply. Otherwise,
repair the faulty part.
NL02-2092b
EN01 发动机控制模块线束连接器
1
2
4
5
3
81
63
44
25
6
62
43
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
26
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
45
46
61 60 59 58
57 56 55
54 53 52 51 50 49 48 47
64
65
66
80 79 78 77 76 75 74 73 72 71 70 69 68 67
7
Test Items
Standard Value
EN13(A)-EN01(7)Resistance value
Less than 1 Ω
EN13(A)-reliable grounding resistance value
10 kΩ or higher
EN13(A)-Reliable grounding voltage value
0V
Execute next step as per normal.
Step 7
Inspect the ECM Power Supply Circuits.
(a) Inspect whether ECM power supply circuit is normal.
(b) Inspect whether ECM ground circuit is normal.
Step 8
Replace ECM
Refer to 2.12.7.11 Crankshaft Position Sensor (CKP) Learn to carry out the crankshaft position
sensor learn after replacing the ECM.
Step 9
Use a fault diagnosis tester to confirm whether the DTC Code is stored again.
(a) Connect fault diagnosis tester to the diagnostic interface.
Next
No
Repair the faulty part.
Yes
Next
EN01 engine control module harness
connector
808
(b) Turn ignition switch to ON position.
(c) Clear DTC code.
(d) Start and run the engine at idle speed to warm up the engine for at least 5 min.
(e) Road test the vehicle for at least 10 min.
(f) Read control system DTC code again to confirm that the system has no DTC code.
Step 10
Troubleshooting
5. Maintenance
guide
:
Refer to 2.12.8.5 “Replacement of Fuel Injectors” to replace the fuel injectors.
No
Refer to 2.2.7.3 Intermittent Fault
Inspection for intermittent fault.
Yes
809
2.12.7.32 DTC P0270 P0271
1. DTC
description:
DTC P0270
Cylinder No.4 fuel injector circuit low voltage fault
DTC P0271
Cylinder No.4 fuel injector circuit high voltage fault
Fuel injectors operating voltage is provided by The Main Relay controlled by ECM. Battery
voltage passes through the main relay terminal No.3 to all fuel injector wiring harness connectors
terminal No.A. ECM controls Cylinder No.4 fuel injector internal ground circuit through ECM
harness connector EN01 terminal No.26. ECM monitors all fuel injector driver circuits status, if
ECM detects driving circuit status corresponding voltage is incorrect, ECM will set a fuel injector
control circuit fault DTC code.
2. Conditions For Setting DTC and The Fault Location:
DTC Code
DTC
Detection
Strategy
Conditions For Setting The
DTC (Control Strategy)
Fault Locations
P0270
Hardware
Circuit
Inspection
Injector Signal Circuit Open
or Short To Ground
P0271
Hardware
Circuit
Inspection
Injector Signal Circuit Short
To Power Supply
1. Sensor
Circuit
2. Sensor
3. ECM.
3. Circuit
sketch
NL02-2093b
44
EN01
ECM
BAT
15
A
E
F2
1
MPR
86
87
30
85
发动机主继电器
25
EN01
A
EN14
B
EN14
INJC
4缸燃油喷射器
Engine
main relay
4th cylinderfuel
injector
810
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст