Geely Emgrand X7. Manual part — 475
Geely Emgrand X7. Manual part - 475
Standard Resistance: More than 10 Ω or higher
Confirm if the resistance conforms to standard
value.
6
Replace the BCM
(a) Replace BCM and refer to Replacement of BCM in 11.8.8.1.
Confirm the completion of repair.
7
The system is normal.
Yes
The system is normal.
No
Next
1899
10.2.4.4 DTC B1203 B1204
Fault diagnosis code Descriptions
B1203
Right stop lamp open circuit fault
B1204
Right stop lamp short circuit to grounding fault
Circuit diagram:
9 CA12
5 CA12
9 CA18
5 CA18
2 SO24
3 SO24
LH-LAMP
RH-LAMP
10 IP49
20 IP49
2 SO31
3 SO31
BCM
左前组合
大灯
(位置灯)
右前组合
大灯
(位置灯)
右后组合
大灯
(位置灯)
左后组合
大灯
(位置灯)
NL11-3251b
Diagnostic Steps:
1
Check any fault code except for B1203 B1204.
(a) Check if any fault code exists except for B1203 B1204.
2
Measure right stop lamp voltage.
Yes
Go to
(DTC) list in 10.2.4.2
and repair according
to trouble codes.
No
Left front
combinatio
n headlamp
(position
lamp)
Left rear
combinatio
n headlamp
(position
lamp)
Right
rearcombin
ation
headlamp
(position
lamp)
Right front
combination
headlamp
(position
lamp)
1900
(a) Turn on position lamp.
(b) Measure voltage of right front stop lamp harness
connector CA18 terminal9.
(c) Measure Right rear stop lamp harness connector
SO24 terminal2 voltage.
Standard Voltage: 11-14 V
1
2
3
4
5
6
S024
CA18
右后位置灯线束连接器
NL11-3203b
9
8
7
4
3
2
6
5
1
右前位置灯线束连接器
3
Inspect the bulb.
(a) Inspect whether parking lamp bulb is burned out.
Confirm whether the parking lamp bulb is blown out.
4
Inspect the communication between BCM and right
parking lamp.
(a) Turn the ignition switch to OFF position.
(b) Disconnect BCM wire harness connector IP49.
(c) Disconnect right front parking lamp wire
harness connector CA18.
(d) Disconnect right rear stop lamp harness
connector SO24.
(e) Measure resistance between BCM wire
harness connector IP49 terminal 20 and right
front brake lamp wire harness connector CA18
terminal 9.
(f) Measure resistance between BCM wire
harness connector IP49 terminal 20 and right
rear wire harness connector SO24 terminal 2.
Standard Resistance: Less than 1 Ω
Confirm if the resistance conforms to standard
value.
1
2
3
4
5
6
S024右制动灯线束连接器
IP56制动灯开关线束连接器
1
2
NL11-3204b
No
Go to step 4
Yes
Yes
Replace the bulb.
No
SO24 right rearposition lamp harness connector
CA18 right front position lamp harness connector
IP56Brake lamp switchharness connector
SO24 right Brake lamp harness connector
1901
5
Inspect the communication between the right parking lamp and grounding.
(a) Disconnect right front stop lamp harness
connector CA18.
(b) Disconnect right rear parking lamp harness
connector SO24.
(c) Measure resistance value between of right front
stop lamp harness connector CA18 terminal5 and
grounding.
(d) Measure resistance between right rear parking
lamp wire harness connector SO24 terminal 3
and grounding.
Standard Resistance: Less than 1 Ω
(e) Measure resistance between right front parking
lamp wire harness connector CA18 terminal 5
and grounding.
(f) Measure right rear parking lamp wire harness
connector SO24 terminal 3 and grounding.
Standard Resistance: More than 10 Ω or higher
Confirm if the resistance conforms to standard value.
1
2
3
4
5
6
S024右制动灯线束连接器
NL11-3205b
6
Replace the BCM
(a) Replace BCM and refer to
Replacement of BCM in 11.8.8.1
.
Confirm the completion of repair.
7
The system is normal.
No
Repair or replace the harness.
Yes
No
Repair or replace the harness.
Yes
Next
SO24 right Brake lamp harness connector
1902
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст