Geely Emgrand X7. Manual part — 133
Geely Emgrand X7. Manual part - 133
2.7.6.4 Replacement of Intermediate Muffler Assembly
Dismantlement Procedure
1. Lift the vehicle, refer to 1.3.1.1
Lifting and Raising the Vehicle.
Warning: Refer to Warning on
Vehicle Lifting and Jacking in
Warnings and Precautions.
2. Dismantle the retaining nuts and
the exhaust pipe gasket of the
middle muffler assembly .
NL03-0013c
3. Dismantle the middle muffler to
the rear muffler retaining bolts
and the exhaust pipe gasket.
3. Dismantle the three rear rubber
bearings from the Middle
muffler.
Note: Do not drop the muffler during
the removal.
4. Remove the Middle muffler
assembly.
5. Inspect whether the three-way
catalytic muffler has holes,
damage and cracks.
NL03-0014c
Installation Procedure:
1. Install three rear rubber bearings
to the middle muffler assembly.
2. Install the exhaust pipe gasket
between the Middle muffler and
the three-way catalytic
converter .
NL03-0015c
531
3. Install and tighten the Middle
muffler retaining nuts.
Torque :47-57N . m(Metric) .34. 8-42.
2lb-ft(English system)
4. Install the front muffler gasket.
5. Install and tighten the front and
rear muffler retaining nuts.
Torque :35-45N . m(Metric). 25.
8-33 . 2lb-ft(English system)
6. Lift down vehicle from lifter.
7. Inspect whether the exhaust
system leaks air.
NL03-0013c
532
2.7.6.5 Replacement of Rear Muffler Assembly
Dismantlement Procedure
1. Lift the vehicle, refer to 1.3.1.1
Lifting and Raising the Vehicle.
Warning: Refer to Warning on
Vehicle Lifting and Jacking in
Warnings and Precautions.
2. Remove the fixing bolts, springs
and the exhaust pipe seal gasket
between rear muffler and middle
muffler.
Warning: Do not carry out the
dismantlement procedure at
warming-up stage, as this may
result in burns.
NL03-0017c
3. Dismantle two front rubber
support seat
4. Remove
rear
muffler
5. Inspect whether there are holes,
damage or cracks for rear
muffler.
NL03-0016c
Installation Procedure:
1. Install two front rubber bearings.
2. Install the exhaust pipe seal
gasket.
3. Install the fixing bolts and
springs of front muffler assembly
and rear muffler assembly.
Torque :35-45N . m(Metric). 25. 8-33.
2lb-ft(English system)
4. Lower
the
vehicle.
5. Inspect the exhaust system for
leakage.
NL03-0016c
533
2.8 Cooling system
2.8.1 Specifications
2.8.1.1 Fastener Specifications
Tightening Torque
Applications Specification
Metric (N.m)
English system
(lb-ft)
Water Pump Long Mounting
Bolt
M6×35
9 - 13
6 . 7 - 9 . 6
Water Pump Short Mounting
Bolt
M6×25
8 - 10
6 - 7.4
Engine coolant temperature
sensor
M12×1 . 5
16 - 24
12 - 17.7
Fan Assembly Mounting Bolt
M6×20
8 - 10
6 - 7.4
Fan Motor Nut
M10
10
7.4
Fan Motor Retaining Screw
M6×18
8 - 10
6 - 7.4
Fixing Bolts of Radiator
M8×25
10 - 11
7 . 4 - 8 . 1
Fixing bolt of expansion tank
assembly
M6×20
8 - 10
6 - 7.4
Engine water inlet pipe adapter
assembly is installed with nut.
M6
9 - 13
6 . 7 - 9 . 6
Coolant Valve Component
M10×1
Above 25
Above 18.5
Engine Coolant Inlet Pipe
Component
M6
9 - 13
6 . 7 - 9 . 6
2.8.1.2 Cooling System Specification
Applications Specification
Cooling Type
Coolant
Engine Coolant Capacity (Coolant
Recovery Reservoir)
6 . 5 L(11 . 44 pt)
Engine Coolant Specification /
Grades
Glycol engine coolant from Geely major plant with the
ultra-long acting and the freezing point at (-40 /
℃
-40 °F)
534
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст