Geely Emgrand X7. Manual part — 612
Geely Emgrand X7. Manual part - 612
NL11-2214b
IP48 车身控制模块线束连接器2
1 2 3
4 5 6
7 8 9
10 11 12 13
5
5
Inspect the voltage of the terminal No. 5 of BCM wire harness connector IP48.
(a) Press lock switch to measure the
voltage of terminal No. 5 of
BCM wire harness connector
IP48.
Standard voltage: 11 - 14 V
Confirm if the voltage conforms to
standard value.
NL11-2214b
IP48 车身控制模块线束连接器2
1 2 3
4 5 6
7 8 9
10 11 12 13
5
6
Replace the BCM
(a) Replace BCM and refer to Replacement of BCM in 11.8.8.1.
Confirm whether the compartment is working correctly.
Yes
Go to step 7
No
Yes
The system is normal.
No
IP48body control module harness
connector2
IP48body control module harness
connector2
2447
7
Inspect the back lock motor.
(a) Open back door, meanwhile
measure resistance between door
lock motor wire harness
connector SO43 terminal No. 3
and terminal No. 4.
Standard resistant value :is less than
1Ω
Confirm if the resistance conforms to
standard value.
NL11-2215b
3
1
4
2
SO43 后背门门锁电机线束连接器
4
3
8
Replace opening switch of trunk
(a) Replace rear backdoor lock motor, Refer to11.7.7.2 rear door lock block replacement .
Confirm whether the compartment is working correctly.
(a) Inspect and repair short-circuit fault between back door lock motor wire harness connector
SO43 terminal No. 4 and grounding.
Standard resistant value :is less than 1Ω
10
The system is normal.
9
Inspect the circuit between the terminal No. 4 of the back door lock motor wire harness
connector SO43 and the body grounding.
Next
Yes
The system is normal.
No
Yes
Go to step 9
No
Yes
The system is normal.
No
SO43 rear back-door door lock
motor harness connector
2448
11.9.6.8 Door auto-lock (30km/h) function was failed
Diagnostic steps:
1
Inspect the DTC
A. Connect the special-purpose diagnostic tester.
B. Read the DTC
Confirm whether DTC
2 Clear
DTC
A. Remove the DTCs with a special-purpose diagnostic tester.
Confirm whether the system works normally.
3
Perform the central locking active test function
A. Execute the active locking function of the center control lock with a special-purpose
diagnostic tester.
Confirm whether the central controlled lock may be normally locked.
4
Confirm the vehicle speed signal.
A. Connect the special-purpose diagnostic tester to enter the ABS system to read the vehicle
speed signal data stream when the actual vehicle speed reaches 20km/h and above.
Confirm whether the vehicle speed signal exceeds 20km/h.
5
Repair the BCM circuit.
A. Check the BCM power supply, ground wire and data communication line.
No
Repair the data communication network as well as the ABS
system repairing speed sensor and circuit repairing ECM.
Yes
No
See 11.7.6.4 Mechanical Key/Central Control Lock
Switch Cannot Lock the Central Control Lock.
Yes
Yes
The system is normal.
No
No
Go to step 3
Yes
2449
B. Fix the malfunctions of relevant lines of the BCM.
Confirm whether the system works normally.
6
Replace the BCM
A. Replace BCM and refer to Replacement of BCM in 11.9.8.1.
Confirm the completion of repair.
7
The system is normal.
Next
Yes
The system is normal.
No
2450
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст