Geely Emgrand X7. Manual part — 2

–

Keep halogen bulbs out of the reach of children.

Warning for injector O-ring dismantle

Warning: inspect the lower (small) O-seal ring of various oil sprayers, which can not be retained
on the lower manifold branch to reduce the fire and personal injury risk.

Warning: If the O-ring is not dismantled with the injector, the replacement injector with new
O-rings will not seat properly in the injector socket. Improper seating could cause a fuel leakage.

Warning for moving component and hot surface

Warning: Avoid contacting with moving components and hot surfaces while working around a
running engine in order to prevent personal injury.

Warning for protective goggle and glove

Warning: Approved protective goggles and gloves should be worn when removing the exhaust
system components, or else the sharp edge or the iron rust dropped down from the exhaust system
components may cause serious personal injury.

Warning for fluid reservoir cover

Warning: To avoid being burned, do not remove the fluid reservoir cover while the engine is hot.

If the reservoir cap is dismantled when the engine and the radiator are still hot, the cooling system
will drainscalding high-pressure fluid and steam.

Warning for cooling system maintenance

Warning: provided that there is pressure in the cooling system, the solution temperature is higher
more than the boiling temperature even if the solution in the radiator is not boiling. If pressure cap
is removed while the engine is still hot and under pressure during maintenance, the engine coolant
will boil immediately and spray into the operator's body, causing serious burns.

Warning ofr drain fuel pressure

Warning: Remove the fuel tank cap and drain the fuel system pressure before servicing the fuel
system in order to reduce the risk of personal injury. After you drain the fuel system pressure, a
small amount of fuel may drain when servicing the fuel circuit, the fuel injector, or the
connections. In order to reduce personal injury

Harmful risk: wrap the fuel system component with a rag prior to disconnection. This will catch
any fuel that may leak out. Place the towel in an approved container when the disconnection is
complete.

Warning for road test

Warning: Road test a vehicle under safe conditions and while obeying all traffic laws. Do not
attempt any maneuvers that could jeopardize vehicle control. Failure to adhere to these
precautions could lead to serious personal injury and vehicle damage.

Warning for safety goggles and fuel

Warning: be sure to wear the safety goggles when processing the fuel in order to avoid the fuel
from splashing into the eyes.

Warning for airbag system

Warning: this vehicle is equipped with the SRS system; the following conditions may be caused if
not following the correct operation procedure:

– Airbag

unfold

– Preloader

blister

7

– Injured

person

– Unnecessary

airbag

system maintenance

Warning: comply with the following criteria in order to avoid the above situations:

–

Refer to airbag system component views in order to determine if you are performing service
on or near the airbag system components or the airbag system wiring.

–

If you are doing the repair on the airbag system components, surrounding components or the
circuits, remove the airbag system.

Warning for high temeprature of deployed airbag module

Warning: After deployment, the metal surfaces of the airbag system component may be very hot.
To help avoid a fire or personal injury:

–

Allow sufficient time for cooling before touching any metal surface of the airbag system
component.

–

Do not place the deployed airbag system component near any flammable objects.

Warning for airbag system clock spring

Warning: Improper installation of the clock spring assembly may damage the spiral coil inside the
clock spring. This may result in a malfunction of the coil which may make the airbag module do
not work normally and cause personal injury.

Warning for airbag system module disposal

Warning: In order to prevent accidental deployment of the safety system and avoid the risk of
personal injury, do not dispose of an unexpanded airbag module as normal shop waste.
Unexpanded airbag modules contain substances that could cause severe illness or personal injury
if their sealed containers are damaged during disposal. Use the following deployment procedures
to safely dispose of an unexpanded airbag module.

Warning for taking and storing airbag system module

Warning: When carrying an unexpanded airbag module:

–

Do not carry the airbag module by the wires or connector.

–

Make sure the airbag opening do not point towards you and others.

Warning: when storing unexpanded airbag module, ensure the opening does not face the surface
on which it will be placed. Do not point the airbag opening to the ground. Do not place any items
onto the airbag module. Provide free space for the airbag to expand in case of an accidental
deployment.

Do not have the unexpanded airbag module soaked in water or come into contact with other
liquids.

Do not place the unexpanded airbag module near the fire source or a high-temperature area.
Prevent personal injury caused by accidental airbag deployment.

Warning for handling airbag system collision sensor

Warning: Do not hit or shake airbag system collision sensors. Before supplying power to the
collision sensors, ensure the collision sensors are firmly tightened. Failure to follow the correct
procedures may cause airbag accidental deployment or inoperative, resulting in personal injury.

Important precaution for filling fluid to the brake system

Important precaution: When filling fluid to the brake master cylinder reservoir, use DOT4 brake
fluid from a clean, sealed brake fluid container. The use of any type of fluid other than the

8

recommended type of brake fluid may cause contamination which could result in damage to the
internal rubber seals and/ or rubber linings of hydraulic brake system components.

Important precaution for Anti-corrosion materials

Important precaution: If the power steering system has been serviced, an accurate fluid level
reading cannot be obtained unless air is bled from the steering system. The air in the fluid may
cause pump cavitation noise and may cause power steering pump damage over a period of time.

Important precaution for belt dressing

Important precaution: Do not use belt dressing on the drive belt. Belt dressing causes the
breakdown of the composition of the drive belt. Failure to follow this recommendation will
damage the drive belt.

Important precaution for brake caliper

Important precaution: Support the caliper with a piece of wire when removing the brake caliper to
prevent damage to the brake line.

Important precaution of brake fluid effects on the paint and electrical parts

Important precaution: Avoid spilling brake fluid onto painted surfaces, electrical connections,
wiring, or cables. Brake fluid will damage painted surfaces and cause corrosion to electrical
components. If any brake fluid comes in contact with painted surfaces, immediately flush the area
with water. If any brake fluid comes in contact with electrical connections, wiring, or cables, uses
a clean shop cloth to wipe away the fluid.

Important precaution for damage to fuel tank straps

Important precaution: Do not bend the fuel tank straps. Bending the fuel tank straps may damage
the straps.

Important precaution for engine emissions

Important precaution: Modifications made to the following systems can effect the vehicle's
emission controls and may cause the Malfunction Indicator Lamp (MIL) or “Inspect Engine
Lamp” to illuminate.

– Engine

– Transmission

– Exhuast

System

– Fuel

system

Important precaution: if the replaced tire is not accorded with the performance standard of the
original tire, the emission control of the vehicle may also be affected, which may also result in
turning on the malfunction indicator lamp (MIL), and "check engine" indicator lamp.

Important precaution: Modifications to these systems or the installation of tires with incorrect TPC
could lead to repairs that are not covered by the manufacturer's warranty. This may also cause a
required Emission Inspection/Maintenance test to fail.

Important precaution for engine lifting

Important precaution: When raising or supporting the engine for any reason, do not use a jack
under the oil pan, any sheet metal, or the crankshaft pulley. Lifting the engine in an unapproved
manner may cause component damage.

Important precaution for engine bracket

Important precaution: Broken engine bracket s can cause misalignment of certain drive-train
components which then will cause eventual destruction of the drive-train components.

9

Important precaution: If one engine bracket breaks, the rest engine bracket s will have increased
stress put on them. This could cause the rest of the engine bracket s to break.

Important precaution for excessive adhesive on flywheel bolts

Important precaution: Apply the proper amount of the sealant to the fastener when assembling this
component. Excessive use of the sealant can prohibit the component from being assembled
properly or allow the fastener to loosen. A component or fastener that is not assembled properly
can loosen or fall off leading to extensive engine damage.

Important precaution for exhaust manifold and Oxygen sensor

Important precaution: The oxygen sensor may be difficult to remove when the engine temperature
is above 48°C (120°F). Excessive force may damage threads in the exhaust manifold or the
exhaust pipe.

Important precaution for exhaust system inspection

Important precaution: When inspecting or replacing exhaust system components, make sure there
is adequate clearance from all points on the underbody to prevent overheating of the floor pan and
possible damage to the passenger compartment insulation and trim materials.

Important precaution for torque reaction against timing drive chain

Important precaution: A wrench must be used on the hex of the camshaft when removing or
installing in order to prevent component damage. Failure to prevent the torque reaction against the
timing drive chain can lead to timing drive chain failure.

Important precaution for dismantling external logo

Important precaution: Use a plastic, flat-bladed tool to prevent paint damage when removing an
emblem/name plate.

Important precaution for fastener

Important precaution: Use the correct fastener in the correct position . part number of replaced
fasteners must be correct. Fasteners requiring replacement of or fasteners requiring the use of
thread locking compound or sealant are identified in the service procedure. Do not use paints,
lubrication oil, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified.

These coatings affect fastener torque and joint clamping force and may damage the fastener. Use
the correct tightening sequence and tightening torque when installing fasteners in order to avoid
damage to parts and systems.

Important precaution for fuel pressure

Important precaution: Do not allow the fuel pressure to exceed the specified value because it may
lead to damage to the fuel pressure regulator or fuel pressure gauge.

Important precaution on Handling Electrostatic Discharge Sensitive Components

Important precaution: Electrostatic discharge (ESD) can damage many solid- state electrical
components. ESD susceptible components may not be labeled with the ESD symbol. Handle all
electrical components carefully. Use the following precautions in order to avoid ESD damage:

–

Touch a metal ground point in order to remove your body's static charge before servicing any
electronic component (especially after sliding across the vehicle seat).

–

Do not touch exposed terminals. Terminals may connect to circuits susceptible The ESD
damage.

–

Do not allow tools to contact exposed terminals when servicing connectors.

–

Do not remove components from their protective packaging until required to do so.

10