Geely EC718, EC718RV, EC715, EC715RV. Manual part — 442
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 442
Fuel Gage
Fuel gage input signal is from the fuel level sensor, one end of
the fuel gage is connected to fuel sensor terminal.
Fuel sensor resistance parameters are as following:
Fuel
Resistance
Full
40 ( ± 2 Ω)
3/4
60( ± 2 Ω)
1/2
90( ± 2 Ω)
1/4
140( ± 2 Ω)
Threshold
190 ( ± 2 Ω)
Empty
300 ( ± 2 Ω)
According to the total fuel tank capacity (55 L), LCD display is
divided into eight equal interval value (slightly different in the
low fuel alarm mode). When the fuel amount decreases, if the
current fuel level falls into the appropriate range, the
corresponding LCD segment will be lit.
Fuel Tank Capacity (L/pt)
LCD Segment Display
5-10/8.8-17.6
Empty (The First Segment)
10-13.5/17.6-23.8
First and Second Segment
Light
13.6-20.25/23.9-35.6
First To The Third Segment
Light
20.26-27.0/35.7-47.5
First To The Fourth
Segment Light
27.1-33.75/47.7-59.4
First To The Fifth Segment
Light
33.76-40.5/59.4-71.3
First To The Sixth Segment
Light
40.6-47.25/71.4-83.1
First To The Seventh
Segment Light
47.26-55.0/83.2-96.8
Full (All Light)
When the fuel level is lower than the threshold, low fuel level
warning lamp light.
Engine Coolant Temperature Gage
Engine coolant temperature information is from the CAN bus.
Micro-controller calculates the engine coolant temperature,
and then displays on LCD according to the message sent from
the EMS.
If the CAN message from the EMS is lost continuously for one
minute, or the temperature value is invalid for one minute, LCD
thermometer will show the minimum, and the temperature
warning lamp will be on.
Temperature is displayed in eight segments on LCD. The
temperature corresponding relationships may be adjusted in
the programming and stored in EEPROM. The default
comparison is shown below.
Temperature°C ( ºF)
LCD Segment Display
T
≤ 50 (T ≤ 122)
Low Temperature Sign
(All Off)
50 < T
≤ 70 (122 < T ≤ 158)
First Segment Light
70 < T
≤ 80 (158 < T ≤ 176)
First and Second
Segment Light
80 < T
≤ 90 (176 < T ≤ 194)
First To The Third
Segment Light
90 < T
≤ 100 (194 < T ≤ 212)
First To The Fourth
Segment Light
100 < T
≤ 110 (212 < T ≤ 230)
First To The Fifth
Segment Light
110 < T
≤ 120 (230 < T ≤ 248)
First To The Sixth
Segment Light
120 < T
≤ 124 (248 < T ≤ 255)
First To The Seventh
Segment Light
124 < T
≤ 130 (255 < T ≤ 266)
High Temperature Sign
(All Light)
When the engine temperature reaches 124°C (255 ºF), the
engine overheating warning lamps will be flashing at 1Hz
frequency. For detailed alarm policy, please refer to the table:
Previous Alarm
Status
Temperature T °C
( ºF)
Next Status
No Overheating
Alarm
T
≥ 124 (T ≥ 255)
An Overheating
Alarm
Overheating
Alarm
T<121 (T<250)
Overheating
Lifted
Body Electric
Instrument / Driver Information System
11-281
Door Status Display
Four doors information is from the CAN bus, sent by the BCM
module. Instrument cluster shows each door information on
LCD display. When the vehicle speed is greater than 10 km/h,
if a door opens, the corresponding LCD segment will be
blinking, body icon shows on LCD, buzzer will ring until all
doors are closed; when the speed is less than or equal to 10
km/h, if a door opens, the corresponding LCD segment will be
lit (not blinking), body icon shows on LCD, but the buzzer does
not ring.
When the engine is shut down, if a door opens and there is no
other alarm, the LCD will show the door open status for 4 s.
The instrument panel goes into sleep mode, while there is no
LCD information display, no backlight.
When the engine is shut down, if the engine hood opens or the
rear compartment lid opens and there is no other alarm, then
the LCD backlight illuminates. LED shows corresponding
status, also shows the status of each door. After 4 s, the
instrument panel goes to sleep. At the same time there is no
LCD information display, no backlight.
If the key is not pulled out or park lamps are not turned off,
although the engine is shut down, the LCD will be backlight on.
LCD shows the status of each door until the alarm expires or
the alarm is deactivated. After the alarm, instrument panel goes
to sleep. At the same time there is no LCD information display,
no backlight.
When the engine is shut down, if the hazard warning lamp is
enabled, then the LCD backlight will be on, the right and left
turn signal lamps start flashing. LCD shows the status of each
door until the hazard warning lamp is turned off. If there is no
other alarm, the instrument panel goes to sleep. At the same
time there is no LCD information display, no backlight.
Odometer
Display Range: 6 digits, maximum 999,999 km
Accuracy: 1 km
Odometer shows the total vehicle mileage. When the total
mileage reaches the maximum reading (999,999 km), the
display remains unchanged. In order to prevent a total mileage
value loss, micro-controller updates the value stored in
EEPROM once every 2 km. When battery power supply is off,
the total mileage maximum error is 1 km. If reading from the
EEPROM fails, the corresponding display position shows "Err".
After the ignition is turned on, the micro-controller checks the
RAM for the total mileage value. If the RAM value is missing or
invalid, a total mileage reading from the EEPROM will be
displayed on the LCD. The value of the total mileage is stored
in RAM, and its accuracy is 1 km.
In the event of the battery power-down, the engine will be shut
down. Press the mode switch button, ignition on, and maintain
for 20 s. The odometer value is cleared (only when the reading
is less than 256 km). This operation can only be operated once.
11-282
Instrument / Driver Information System
Body Electric
11.7.4 Component Locator
11.7.4.1 Component Locator
Instrument Cluster Front End
1 2
FE11-2016b
Legend
1. Mode Switch Button
2. Reset Button
Body Electric
Instrument / Driver Information System
11-283
Warning Lamps, Gage
4
3
2
6
1
7
120 140
160
80
240
0
60
40
200
180
20
220
100
5
0
8
E
C
F
H
ODO
km/h
km
ABS
P
FE11-2017b
FE11-2017b
11-284
Instrument / Driver Information System
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст