Geely EC718, EC718RV, EC715, EC715RV. Manual part — 71
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 71
No
Step 7
Repair ECM power supply circuit.
(a)
Repair ECM power supply circuit. Refer to
Fault solved?
Yes
System normal
No
Step 8
Replace ECM.
(a)
Connect scan tool.
(b)
Turn the ignition switch to "ON" position.
(c)
Scan ECM DTC codes, identify ECM fault. If necessary,
Replace ECM. Refer to
(d)
Clear DTC code.
Next
Step 9
System normal.
2.2.7.45 Crankshaft rotates, but the engine can not start.
Note
Before carry out this step, make sure the engine oil is comply with the manufacturer requirements, the fuel tank has
sufficient fuel and battery has enough power for starting engine. Observe the scan tool data list, analyze the accuracy
of the data, as these will facilitate diagnostic.
Diagnostic Steps:
Step 1
Check fuel pump fuse.
EF05
1413 12 1110
5
1
2
3
4
6
7
8
9
J
L
K
I
G
D
C
B
E
F
A
86
86
30
87
85
86
86
87
87
87
30
30
30
85
85
85
2
2
3
3
5
5
1
1
1
2
5 3
1
2
5 3
86
87
30
1
1
2
5
3
2
5
3
85
EF01
EF21
EF18
EF25
EF20
EF29
EF06
EF02
EF30
EF17
EF19
EF23
EF22
EF26
EF24
EF08
EF27
EF28
EF05
EF07
EF16
EF04
EF03
EF15
EF12
EF10
EF1
1
EF09
EF13
EF14
EF32
EF31
FE02-5117b
(a)
Check whether the fuel pump fuse is faulty.
(b)
Repair fuel pump fuse power circuit.
(c)
If necessary, replace the faulty fuel pump fuse.
Fault solved?
Yes
System normal
Engine
Control System JL4G18-D
2-199
No
Step 2
Scan ECM for DTC codes.
(a)
Connect scan tool.
(b)
Turn the ignition switch to "ON" position.
(c)
Scan ECM for DTC codes.
(d)
Check DTC P0627 and any fuel system related DTC codes
and repair the faulty part. Refer to
.
(e)
Clear ECM DTC codes.
Start the engine, fault solved?
Yes
System normal
No
Step 3
Check fuel pump relay.
(a)
Connect scan tool.
(b)
Turn the ignition switch to "ON" position.
(c)
Select scan tool "Fuel Pump Relay" in the "Action Test" to
drive the fuel pump relay.
Is fuel pump relay working properly?
Yes
No
Step 4
Replace the fuel pump relay.
(a)
.
(b)
Replace the fuel pump relay.
(c)
Inspect fuel pump relay circuits and repair the faulty part.
Start the engine, fault solved?
Yes
System normal
No
Step 5
Check the fuel pump circuit.
2-200
Control System JL4G18-D
Engine
1
2
3
4
Fuel Pump Harness Connector SO29
FE02-5119b
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect fuel pump harness connector SO29.
(c)
Connect scan tool.
(d)
Turn the ignition switch to "ON" position.
(e)
Select scan tool "Fuel Pump Relay" in the "Action Test" to
drive the fuel pump relay.
(f)
Connect SO29 terminal 3 and 4 with a test lamp.
Is test lamp lit properly?
Yes
No
Step 6
Repair the fuel pump circuit.
1
2
3
4
Fuel Pump Harness Connector SO29
FE02-5120b
(a)
Turn the ignition switch to "ON" position.
(b)
Check the fuel pump working circuits. Repair the fuel pump
relay open circuit fault between SO29 terminal No.3 and No.
5.
Start the engine, fault solved?
Yes
System normal
No
Step 7
Check the fuel pressure.
(a)
Turn the ignition switch to "OFF" position.
(b)
Install fuel pressure gage and connect scan tool.
(c)
Turn the ignition switch to "ON" position.
(d)
On the scan tool, select scan tool "Fuel Pump Relay" in the
"Action Test" to drive the fuel pump relay.
Standard Fuel Pressure Value: 400 kPa
Is fuel pressure normal?
Yes
No
Step 8
Replace the fuel pump.
(a)
Turn off the ignition switch and remove the ignition key.
Engine
Control System JL4G18-D
2-201
(b)
Replace fuel pump assembly. Refer to
.
Start the engine, fault solved?
Yes
System normal
No
Step 9
Inspect (repair) fuel injectors.
(a)
Inspect (repair) fuel injectors. Refer to the DTC
code
in the repair
procedures. If necessary, replace the faulty fuel injectors.
Start the engine, fault solved?
Yes
System normal
No
Step 10
Check the ignition coil.
(a)
Turn the ignition switch to "OFF" position.
(b)
Remove the cylinder ignition wire. Connect a new wire
connect the spark plug to a reliable ground.
(c)
Remove the fuel pump fuse.
(d)
Start the engine.
Is spark plug ignition normal?
Yes
No
Step 11
Replace the ignition coil.
(a)
Turn off the ignition switch and remove the ignition key.
(b)
Replace the ignition coil. Refer to
Start the engine, fault solved?
Yes
System normal
No
Step 12
Check crankshaft position sensor and circuit.
(a)
Check crankshaft position sensor. Refer to
.
(b)
Measure the crankshaft position sensor resistance with a
multimeter.
Standard Resistance: 870 Ω
(c)
Inspect the sensor circuit. Repair the faulty part. If necessary,
replace the crankshaft position sensor. Refer to
Crankshaft Position Sensor Replacement
Start the engine, fault solved?
2-202
Control System JL4G18-D
Engine
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст