Geely EC718, EC718RV, EC715, EC715RV. Manual part — 58
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 58
Fuel Injector
12
From Battery
Main Relay
Cylinder No.1 Fuel Injector
Cylinder No.2 Fuel Injector
Cylinder No.3 Fuel Injector
Cylinder No.4 Fuel Injector
Engine
Control
Module
FE02-5076b
4. Diagnostic Steps:
Note
–
If the control system stores DTC other than misfire, diagnose these DTC first and eliminate the faults.
–
If the vehicle does not have a misfire when sent to a service station, road test the vehicle, so that the misfire will
occur again. Use scan tool to record ECM data when misfire is occurring, in order to facilitate analyzing the cause
of the fault.
–
If after a long period road test, ECM does not store any misfire associated DTC codes, then the fault may be due
to the following reasons:
•
Overfill fuel tank and fuel enters into the evaporative emission control system, so that the mixture is too rich and
causes misfire.
•
Use improper fuel caused poor combustion and misfire.
•
Contaminated spark plug causes the ignition failure and misfire.
•
Carry out basic checks at fault locations identified by DTC codes.
–
Road test the vehicle after repair to confirm no DTC is stored.
Step 1
Initial inspection.
(a)
Check the wiring harness connector for damage, poor
connection, aging or signs of loosening.
Engine
Control System JL4G18-D
2-147
(b)
Check the vacuum tube for damaged, loose, leakage and so
on.
Next
Step 2
Check for other DTC codes.
(a)
Connect scan tool to the datalink connector.
(b)
Turn the ignition switch to "ON" position.
(c)
Press the scan tool power button.
(d)
Select the following menu items: Engine/Read DTC codes.
(e)
Read DTC codes.
Results:
DTC Codes Shown
To Step
DTC Codes Other Than DTC P0300-P0304
No
DTC P0300-P0304
Yes
No
Yes
Step 3
Check valves and air intake system.
(a)
Check vacuum solenoid valve Canister connection is correct
or not and leakage.
(b)
Check the vacuum brake booster vacuum tube connection is
correct or not and leakage.
(c)
Check the intake tube pressure sensor connection is correct
or not and leakage.
(d)
Check purged crankcase ventilation valve, ventilation pipe
connection is correct or not and leakage.
(e)
Check whether there is intake leakage.
Is there above mentioned fault?
Yes
No
Step 4
Check the Spark Plug.
(a)
Remove the spark plug from the misfire cylinder.
(b)
Check whether the spark plug gap is too large or too small.
Standard Gap: 0.8-0.9 mm (0.031-0.035 in)
(c)
Check the existence of spark plug electrode erosion,
damage.
(d)
Check whether the spark plug and the electrode part skirt is
wet or not and check the existence of a serious gasoline
leakage.
(e)
Reinstall the spark plug.
Is there above mentioned fault?
2-148
Control System JL4G18-D
Engine
Yes
Replace the spark plug. Refer to
No
Note
Prior to the implementation of this program, the following conditions must be met:
1. Disconnect all fuel injector connectors.
2. Engine running time must not be longer than 5 s.
Step 5
Check whether the spark plug arcing is normal.
(a)
Test the spark.
(b)
Remove misfire cylinder ignition wires.
(c)
Disconnect all fuel injector cylinder connectors.
(d)
Install the ignition wires to the spark plug.
(e)
Run the engine (the engine running time no longer than 5 s)
and check the arcing.
(f)
Reconnect all cylinder fuel injector connectors.
(g)
Install the ignition wires.
Is spark plug arcing normal?
No
Yes
Step 6
Check the misfire cylinder compression pressure.
(a)
For detailed steps. Refer to
Is cylinder compression pressure normal?
Yes
No
Step 7
Check the cause of cylinder compression pressure too low. Refer to the "Engine Mechanical System" in
the
Diagnostic Information and Procedures
Step 8
Check fuel and misfire cylinder fuel injectors.
(a)
Check whether there is fuel injectors leakage and stagnate.
(b)
Check fuel quality.
Is there above mentioned fault?
Yes
Repair the faulty part. Go to step 17
No
Note
Prior to the implementation of this test, the following conditions must be met:
1. Disconnect all fuel injector connectors.
Engine
Control System JL4G18-D
2-149
2. Run the engine for no longer than 5s.
Step 9
Use a properly working spark plug and check whether there is misfire cylinder arcing.
(a)
Replace the installed spark plug with a spark plug that works
properly.
(b)
Test spark plug.
(c)
Remove misfire cylinder ignition wires.
(d)
Disconnect all fuel injector cylinder connectors.
(e)
Install the ignition wires to the spark plug.
(f)
Run the engine (the engine running time no longer than 5 s)
and check the arcing.
(g)
Reconnect all cylinder fuel injector connectors.
(h)
Install the ignition wires.
Is spark plug arcing normal?
No
Check the ignition coil and ignition wire. Go to
step 17
Yes
Replace the spark plug. Refer to
Step 10
Check ECM connector terminal voltage of the misfire cylinder fuel injector.
FE02-5077b
1
3
5
7
8
6
4
2
9
10
11
12
13
23
24
25
26
27
28
29
30
37
51
52
53
54
55
56
57
58
59
60
61
62
63
64
38
39
40
41
42
43
44
45
46
47
48
49
50
31
32
33
34
35
36
14
15
16
17
18
19
20
21
22
ECM Harness Connector EN01
(a)
Turn the ignition switch to the "ON" position.
(b)
Connect ECM harness EN01.
(c)
Measure ECM harness connector EN01 terminal voltage
according to the following table.
Connector Terminal
Standard Value
EN01 (49)
9-14 V
EN01 (50)
EN01 (63)
EN01 (64)
Is voltage the specified value?
No
Check the fuel injector circuit. Refer to
Yes
Step 11
Check the misfire cylinder valve gap.
(a)
Refer to the "Engine Mechanical System" in
the
, Is valve clearance
normal?
No
Adjust the valve clearance. Go to step 17
2-150
Control System JL4G18-D
Engine
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст