Geely EC718, EC718RV, EC715, EC715RV. Manual part — 187
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 187
3. Schematic:
Engine Coolant Temperature Sensor
Engine
Control
Module
FE02-5208b
4. Diagnostic Steps:
Warning!
Refer to "Cooling System Service Warning" in "Warnings and Notices".
Note
Before carrying out this diagnosis step, observe the data list on scan tool and analyze the accuracy of the data, as
these will help with quick diagnosis.
Note
At any time do not use flammable antifreeze, such as alcohol. Combustible antifreeze can cause serious fires.
Step 1
Initial Inspection
(a)
Check the engine coolant temperature sensor whether there
is evidence of corrosion, as well as the engine coolant is
leaking through the sensor.
(b)
Check whether the engine coolant level is correct.
Next
Step 2
Measure engine coolant temperature sensor resistance.
(a)
Turn the ignition switch to "OFF" position.
Engine
Control System JL4G15-D
2-663
(b)
Disconnect the engine coolant temperature sensor wiring
harness connector EO23.
(c)
Measure engine coolant temperature sensor resistance.
Standard Resistance: (Refer to the specific
parameters
Temperature Sensor Temperature and
(d)
Connect the engine coolant temperature sensor wiring
harness connector EO23.
Is the resistance specified value?
No
Replace the engine coolant temperature
sensor. Go to step 9
Yes
Step 3
Measure engine coolant temperature sensor signal circuit.
FE02-5344b
1 2 3
Engine Coolant Temperature Sensor Harness
Connector EO23
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the engine coolant temperature sensor wiring
harness connector EO23.
(c)
Turn the ignition switch to "ON" position.
(d)
Measure voltage between engine coolant temperature
sensor EO23 terminal No.1 and a reliable ground.
Standard Voltage: 4.7-5 .5 V
(e)
Connect the engine coolant temperature sensor wiring
harness connector EO23.
Voltage normal?
No
Yes
Step 4
Measure engine coolant temperature sensor ground circuit.
FE02-5345b
1 2 3
Engine Coolant Temperature Sensor Harness
Connector EO23
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the engine coolant temperature sensor wiring
harness connector EO23.
(c)
Turn the ignition switch to "ON" position.
(d)
Measure resistance between engine coolant temperature
sensor wiring harness connector EO23 terminal No.3 and A
reliable ground.
Standard Resistance: Less than 3 Ω
(e)
Connect the engine coolant temperature sensor wiring
harness connector EO23.
Resistance normal?
No
Yes
2-664
Control System JL4G15-D
Engine
Step 5
check the engine coolant temperature sensor signal circuit.
FE02-5346b
1
17
33
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 2 3
ECM Harness Connector EO01
Engine Coolant Temperature Sensor Harness
Connector EO23
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the engine coolant temperature sensor wiring
harness connector EO23.
(c)
Disconnect ECM harness connector EO01.
(d)
Measure resistance between engine coolant temperature
sensor wiring harness connector EO23 terminal No.1 and
ECM harness connector terminal No.24. Check whether the
circuit is open.
(e)
Measure resistance between engine coolant temperature
sensor wiring harness connector EO23 terminal No.1 and a
reliable ground. Check whether the circuit is short to ground.
(f)
Measure voltage between engine coolant temperature
sensor wiring harness connector EO23 terminal No.1 and a
reliable ground. Check whether the circuit is short to power
supply.
Test Items
Standard Value
Resistance Between EO23 (1) and EO01
(24)
Less than 1 Ω
Resistance Between EO23 (1) and A
Reliable Ground
10 kΩ or higher
Voltage Between EO23 (1) and A Reliable
Ground
0 V
Next
Step 6
Check the engine coolant temperature sensor ground circuit.
Engine
Control System JL4G15-D
2-665
FE02-5347b
1
17
33
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 2 3
ECM Harness Connector EO01
Engine Coolant Temperature Sensor Harness
Connector EO23
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the engine coolant temperature sensor wiring
harness connector EO23.
(c)
Disconnect ECM harness connector EO01.
(d)
Measure resistance between engine coolant temperature
sensor wiring harness connector EO23 terminal No.3 and
ECM harness connector terminal No.29. Check whether the
circuit is open. Otherwise, repair the faulty part.
(e)
Measure voltage between engine coolant temperature
sensor wiring harness connector EO23 terminal No.3 and a
reliable ground. Check whether the circuit is short to power
supply. Otherwise, repair the faulty part.
Test Items
Standard Value
Resistance Between EO23 (3) and EO01
(29)
Less than 1 Ω
Voltage Between EO23 (3) and A Reliable
Ground
0 V
Execute next step as per normal.
Next
Step 7
Check ECM power supply circuit.
(a)
Check whether ECM power supply circuit is normal.
(b)
Check whether ECM ground circuit is normal.
No
Repair the faulty part.
Yes
Step 8
Replace ECM.
(a)
Replace ECM. Refer to
(b)
Carry out crankshaft position sensor self learn. Refer to
Crankshaft Position Sensor (CKP) Learn
Next
Step 9
Use scan tool to confirm whether the DTC code is stored again.
(a)
Connect scan tool to the datalink connector.
(b)
Turn the ignition switch to "ON" position.
(c)
Clear DTC code.
(d)
Start and run the engine at idle speed to warm up the engine
for at least 5 min.
(e)
Read control system DTC code again to confirm that the
system has no DTC code.
2-666
Control System JL4G15-D
Engine
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст