Geely EC718, EC718RV, EC715, EC715RV. Manual part — 385
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 385
Next
Step 5
System normal.
11.3.6.10 Navigation Unit Can Not Be Turned Off
Schematic:
Radio Control Can Not Be Turned On
schematic.
Diagnostic Steps:
Step 1
Check the navigation unit trigger working power supply.
1
6 7 8
9 10 11 12
2 3
4 5
Navigation Module Harness Connector IP33
FE11-5221b
(a)
Remove the navigation unit. Refer to
(b)
Turn the ignition switch to "OFF" position.
(c)
Disconnect navigation unit harness connector IP33.
(d)
Measure voltage between the navigation unit harness
connector IP33 terminal No.7 and a reliable ground.
Standard Voltage: 0 V
Is the voltage Standard Value?
No
Navigation unit power circuit failure. Refer to
the
Radio Control Can Not Be Turned
Yes
Step 2
Replace the navigation unit. Refer to
.
11.3.6.11 Navigation Normal Boot But The Speakers Inoperative
Radio Control Can Be Turned On But The Speakers Are Inoperative
.
Body Electric
Navigation
11-53
11.3.6.12 Navigation Panel Background Light Is Not On When The Park Lamps Are On.
Schematic:
IP13
3
IP13
4
IP13
2
IP33
9
IP
+B
C01
34
C01
33
C02
7
C05
C
IF23
10A
I/P Fuse Block
Park Lamp
Relay
Background Light Switch
Interior Background
Lighting
Radio Control
Assembly Lighting
FE11-5217b
Diagnostic Steps:
Note
Before this diagnostic procedures, verify the vehicle park lamps working status. if the park lamps are inoperative, please
rule out the park lamp failures (Refer to 11.4.7.5
Park Lamp Inoperative) before the implementation of this diagnostic
procedures.
Step 1
Check the air-conditioning control panel, electric windows and the background light switch.
Is the background light normal?
No
Yes
Step 2
Check the navigation unit background light input voltage.
11-54
Navigation
Body Electric
1
6 7 8
9 10 11 12
2 3
4 5
Navigation Module Harness Connector IP33
FE11-5218b
(a)
Turn the ignition switch to "OFF" position.
(b)
Remove the navigation unit. Refer to
(c)
Disconnect the navigation harness connector IP33.
(d)
Turn the ignition switch to "ON" position.
(e)
Turn on the park lamp.
(f)
Adjust the background light adjustment switch to the brightest
locations.
(g)
Measure navigation unit harness connector IP33 terminal 9
voltage.
Standard Voltage: 11-14 V
(h)
Connect the navigation harness connector IP33.
Is the voltage Standard Value:?
No
The circuit between the IP33 terminal No. 9
and the regulation background light switch
IP13 No.2 terminal is open.
Yes
Step 3
Replace the navigation unit. Refer to
.
Step 4
Check the background light adjustment switch voltage.
1 2 3 4
Background Light Switch Harness
Connector IP13
FE11-5219b
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the background light adjustment switch wiring
harness connector IP13.
(c)
Turn the ignition switch to "ON" position.
(d)
Turn on the park lamp.
(e)
Measure the background light adjustment switch harness
connector IP13 terminal 3 voltage.
Standard Voltage: 11-14 V
(f)
Connect the regulator switch harness connector IP13.
Is the voltage Standard Value:?
No
The circuit between the IP33 terminal No.3
and the I/P fuse block terminal No.33 is open.
Yes
Step 5
Check regulator switch ground circuit resistance.
Body Electric
Navigation
11-55
1 2 3 4
Background Light Switch Harness
Connector IP13
FE11-5220b
(a)
Turn the ignition switch to "OFF" position.
(b)
Disconnect the background light adjustment switch wiring
harness connector IP13.
(c)
Measure the resistance between background light
adjustment switch IP13 terminal No. 4 and a reliable ground.
Standard Resistance: Less than 1 Ω
(d)
Connect the regulator switch harness connector IP13.
Is the resistance normal?
No
The circuit between the IP13 terminal No. 4
and a reliable ground is open.
Yes
Step 6
Replace the background light adjustment switch. Refer to the
Adjustment Switch and Headlamp Height Adjustment Switch Replacement
.
11.3.6.13 The Screen Is Not Dimmed When The Park Lamps Are On
Schematic:
Navigation Panel Background Light Is Not On When The Park Lamps Are On.
Diagnostic Steps:
Step 1
Navigation panel switch background light normal?
No
Background Light Is Not On When The Park
Lamps Are On.
diagnostic step.
Yes
Step 2
Check the navigation unit internal settings.
(a)
Enter into the navigation interface display settings.
(b)
Check the display settings whether the automatic mode is set
to "on"
No
Set the display settings automatic mode to
"on".
Yes
Step 3
Check the navigation unit power circuit and ground circuit.
(a)
Refer to
Radio Control Can Not Be Turned On
Power circuit and ground circuit normal?
No
After diagnostic, go to Step 1.
11-56
Navigation
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст