Geely EC718, EC718RV, EC715, EC715RV. Manual part — 371

Geely EC718, EC718RV, EC715, EC715RV. Manual part - 371

Test Content

Testing Requirements

DTC

Cause

Right Turn Lamp Switch Circuit

B2281

Right turn signal
lamp switch circuit is
short to ground.

Automatic Headlamp Switch
Circuit

B1695

Automatic
headlamp switch
circuit is short to
power supply.

Headlamps Switch Circuit

B2598

Headlamp circuit
and headlamp relay
circuit are short to
power supply.

Park Lamp Switch Circuit

1. Shift lever is in neutral.

2. Headlamp switch is at OFF position.

B1697

Park lamp circuit
and park lamp relay
circuit are short to
power supply.

Key Insert Switch Circuit

1. Ignition key is not inserted.

2. Rear window defroster switch and emergency

alarm push button are in natural.

B1093

Key insert switch
circuit is short to
ground.

Rear Window Defroster Switch
Circuit

B1343

Rear window
defroster switch
circuit is short to
ground.

Emergency

Alarm

Switch

Circuit

B1875

Emergency alarm
switch circuit is
short to ground.

Vehicle Control System

Computer / Integrated Systems

10-21

10.2.5 Removal and Installation
10.2.5.1 BCM replacement

Refer to

11.10.8.1

BCM Replacement

10-22

Computer / Integrated Systems

Vehicle Control System

10.3 Programming and Set Up

10.3.1 Programming and Set Up

1. Programming Note

Before control module programming, make sure the following
conditions are met:

A. Vehicle System Voltage

a. Charging system should have no trouble. In the control

module programming, firstly rule out the charging
system failure.

b. Battery voltage should be greater than 12 V but less

than 16 V. If the battery voltage is too low, before the
control module programming the battery must be
charged.

c. Do not connect the vehicle battery charger to the

battery. Incorrect or the battery charger or system
voltage caused voltage fluctuations will lead to program
failure or control module damage.

d. Turn off or disable all electrical load, battery load, such

as the following components:

•

Interior Lamps

•

Daylight Lamps (If equipped)

•

Heating, Ventilation and Air-Conditioning (HVAC)
System

•

Engine Cooling Fans, Radio, etc.

B. Ignition switch must be placed in the correct location. In the

programming process, do not change the ignition switch
position, unless the diagnostic unit has instructions.

C. Make sure that all tools connections are solid, including the

following components and circuits:

a. Scan Tool

b. Data Link Connector (DLC) Connections

c. Power Supply Circuit

D. Do not disturb programming tool harness. Unexpected

interruption of programming will lead to program failure or
control module damage.

2. Programming and Set Up After ECM
Replacement

After ECM replacement, read the ECM security procedures.
Refer to

2.5.7.10

Replaced ECM Programming

3. Programming and Setup After ABS Module
Replacement

This device does not require programming or setup.

4. Module Programming and Setup After TPMS
Replacement

Replace the TPMS module, or TPMS sensor. TPMS module
and sensors need to learn specific steps to refer
to

6.7.6.1

Sensor Learn

5. Instrument Cluster Programming and Set Up
After Replacement

This device does not require programming or setup.

6. Programming and Set Up After BCM
Replacement

After replacing BCM, the remote key must be reset, detailed
steps are as follows:

Lift anti-theft case, open the driver door. Turn the key from OFF
to ON 6 times in 10 s. the last stop is at the OFF position. At
this time, the anti-theft indicator light enters the learn mode.
Hold down any key on the remote control device. If the anti-
theft light flashes once, it indicates a successful learn. Four
keys can be learned in a row. 10 s after the completion of four
keys, or after learning one key and the ignition is at "ON". End
for each learn, the previous key id will be replaced.

7. Anti-theft Control Module Programming and
Setup After Replacement

After replacing engine anti-theft control module, read security
program into the module. Refer to

2.5.7.11

Replaced Anti-theft

Module and ECM Programming

8. Ignition Key Programming and Setup After
Replacement

Engine anti-theft system can learn up to five keys. For detailed
steps. Refer to

2.5.7.7

Replaced Key Programming

9. Remote Key Programming and Setup After
Replacement

Refer to

10.3.1