Geely EC718, EC718RV, EC715, EC715RV. Manual part — 218
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 218
4. Diagnostic Steps:
Step 1
Check whether there is other APP sensor related DTC code?
(a)
Connect scan tool to the datalink connector.
(b)
Turn the ignition switch to "ON" position.
(c)
Press the scan tool power button.
(d)
Select the following menu items: Engine/Read DTC codes.
(e)
Read DTC codes.
Results:
DTC Codes Shown
To Step
Only P2138
Yes
P2122, P2123, P2127, P2128
No
No
Yes
Step 2
Check TPS1 and TPS2 output voltage signals.
(a)
For technical specifications. Refer to
Pedal Position Sensor (APP) Check
Specified values?
No
Replace the acceleration pedal. Refer to the
"acceleration pedal assembly replacement."
Yes
Step 3
Check ECM Power Supply Circuit and ground circuit.
(a)
Check ECM Power Supply Circuit and ground circuit. Refer to
ECM power and ground circuits normal?
No
Power and ground circuits fault.
Yes
Step 4
Replace ECM. Refer to
Engine Control Module Replacement
.
Next
Step 5
Carry out crankshaft position sensor learn. Refer to
Crankshaft Position Sensor (CKP) Learn
.
Next
Step 6
Use scan tool to confirm whether the DTC code is stored again.
(a)
Connect scan tool to the datalink connector.
(b)
Turn the ignition switch to "ON" position.
(c)
Clear DTC code.
Engine
Control System JL4G15-D
2-787
(d)
Start and run the engine at idle speed to warm up the engine
for at least 5 min.
(e)
Road test the vehicle for at least 10 min.
(f)
Read control system DTC code again to confirm that the
system has no DTC code.
No
Intermittent Fault. Refer to
Yes
Step 7
Diagnostic completed.
2.12.7.56 DTC P2610
Lack of information, to provide in the future.
2.12.7.57 DTC P0633 U0167 U0426
1. DTC Descriptor:
DTC
P0633
Alarm Does Not Learn Malfunction
DTC
U0167
Anti-theft Device No Response
DTC
U0426
Anti-theft Device Authentication Failure
ECM communicates with Anti-theft control module through ECM harness connector EO01 terminal No.62 R-LIN circuit and wiring
harness connector EO35 terminal No.72 R-LIN circuit. For details, Refer to
2. Conditions For Setting DTC and The Fault Location:
DTC Code
DTC Detection Strategy
Conditions For Setting The
DTC (Control Strategy)
Fault Locations
P0633
Alarm Does Not Learn Malfunction
Ignition Switch "ON".
1. Ignition Key
2. Ignition Key Incentive Coil
3. ECM
4. Chip Security Module
5. Data Circuit (W-LIN Circuit,
R-LIN Circuit)
U0167
Anti-theft Device No Response
Ignition Switch "ON".
1. Ignition Key
2. Ignition Key Incentive Coil
3. ECM
4. Chip Security Module
5. Data Circuit (W-LIN Circuit,
R-LIN Circuit)
2-788
Control System JL4G15-D
Engine
DTC Code
DTC Detection Strategy
Conditions For Setting The
DTC (Control Strategy)
Fault Locations
U0426
Anti-theft Device Authentication
Malfunction
Ignition Switch "ON".
1. Ignition key
2. Ignition Key Incentive Coil
3. ECM
4. Chip Security Module
5. Data Circuit (W-LIN Circuit,
R-LIN Circuit)
3. Schematic:
62
8
5
7
72
IP25
IP25
IP25
EO01
EO35
IMMORQST
SDATA
W LINE
R LINE
K LINE
Engine
Control
Module
To DLC
Engine Lock
System Control
Module
FE02-5296b
4. Diagnostic Steps:
Engine Anti-theft System Warning Lamp Flashing, The Vehicle Can Not Be Started
.
5. Repair Instructions:
Anti-theft system repair. Pefer to anti-theft system,
Diagnostic Information and Procedures
.
Engine
Control System JL4G15-D
2-789
2.12.7.58 Crankshaft Rotation Normal, But The Engine Can Not Start
Note
Before carry out this diagnostic step, make sure the engine oil meets manufacturers requirements and make sure the
fuel tank has sufficient fuel, battery capacity meets the requirements for engine starting. Observe the scan tool data
list, analyze the accuracy of the data, as it will help with quick Diagnostic.
Diagnostic Steps:
Step 1
Check fuel pump fuse.
EF05
1413 12 1110
5
1
2
3
4
6
7
8
9
J
L
K
I
G
D
C
B
E
F
A
86
86
30
87
85
86
86
87
87
87
30
30
30
85
85
85
2
2
3
3
5
5
1
1
1
2
5 3
1
2
5 3
86
87
30
1
1
2
5
3
2
5
3
85
EF01
EF21
EF18
EF25
EF20
EF29
EF06
EF02
EF30
EF17
EF19
EF23
EF22
EF26
EF24
EF08
EF27
EF28
EF05
EF07
EF16
EF04
EF03
EF15
EF12
EF10
EF1
1
EF09
EF13
EF14
EF32
EF31
FE02-5117b
(a)
Check whether the fuel pump fuse is faulty.
(b)
Repair pump fuse power circuit.
(c)
When necessary, replace the faulty fuel pump fuse.
Is fault solved?
Yes
System normal.
No
Step 2
Scan ECM DTC codes.
(a)
Connect scan tool.
(b)
Turn the ignition switch to "ON" position.
(c)
Scan ECM DTC codes.
(d)
Repair any fuel system related DTC code and Repair the
faulty part. Refer to
(e)
Clear ECM DTC code.
Start the engine, fault solved?
Yes
System normal.
No
Step 3
Check fuel pump relay.
(a)
Connect scan tool.
(b)
Turn the ignition switch to "ON" position.
(c)
Choose scan tool "Action Test" then "fuel pump relay" to drive
the fuel pump relay.
Is pump relay working properly?
Yes
2-790
Control System JL4G15-D
Engine
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст