Scania Central gear RP832-RBP832. Manual — part 5
08:04-02
©
17
Removal
1
Remove the end yoke nut. Use socket
98 765.
2
Pull off the end yoke with hydraulic tool as
illustrated.
3
Old type of seal. Remove the sealing ring
using slide hammer 87 596.
Note: Make sure the tip of the slide hammer
does not touch the seal cover.
99 004
99 012
99 003
98 257
99 124
99 001
99 011
101 521
New type of seal: The seal splits in two parts.
One part is on the driver and the other part is in
the seal seat.
4
Remove the part in the seal seat carefully.
Make sure the surface of the seal seat is not
damaged.
5
Remove the dust cover and the part of the
seal on the driver carefully, use pullers
587 319 and 587 318 and support drift
98 568. Make sure the surface of the end
yoke is not damaged.
114 657
587 319
587 318
98 568
Spot repairs
18
©
08:04-02
Fitting
1
Fit the dust cover. Renew the dust cover if it
is damaged.
IMPORTANT! The new seals for the end yokes
cannot be reused once they have been removed.
The seals must be renewed.
2
Press in place the seal on the end yoke with
drift 99 377. Make sure the seal is turned the
right way round, see illustration. The seal
must not be knocked in place.
3
Press in place the end yoke, see illustration.
The end yoke must not be heated as this will
damage the seal.
99 377
113 235
08_1348
4
Tighten the end yoke nut with sleeve
98 675.
IMPORTANT! Tightening torques are different
for the different gears, see below.
RP832
•
Tightening torque 1000 Nm.
88 292
99 129
98 765
111 171
1000 Nm
•
Alternative tightening method
First tighten the nut to 300 Nm using socket
98 765. Mark the socket and yoke as
illustrated and then tighten a further 26 mm
to attain 1000 Nm.
88 292
99 129
1
2
98 765
111 316
Spot repairs
08:04-02
©
19
RBP832
•
Tightening torque 600 Nm
88 292
99 129
98 765
600 Nm
111 493
•
Alternative tightening method
First tighten the nut to 300 Nm using socket
98 765. Mark the socket and yoke as
illustrated and then tighten a further 11 mm
to attain 600 Nm.
88 292
99 129
1
2
98 765
111 316
5
Lock the nut by staking the nut flange into
the recesses in the end yoke in two places.
Spot repairs
20
©
08:04-02
Output shaft RBP832
Special tools
Number
Description
Illustration
Board
88 292
Pull rod
G2
98 297
Assembly sleeve
G3
98 626
Impact tool
AD3
98 765
Splined socket
G2
99 003
Hydraulic cylinder
H1
99 004
Pneumatically driven
hydraulic pump
H1
99 005-1
Adapter
H1
99 012
Fully threaded spindle
H1
99 040
Adapter
H1
99 129
Counterhold
G2
00
1848
88 292
98 297
110 106
98 626
110 811
00_1642
98 765
109 403
99 003
110
1
88
99 004
99 005−1
111 423
109 431
99 012
99 040
110 995
99 129
00_1616
Spot repairs
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст