LEXUS LX 570 (2019 year). Instruction — part 28
443
5-6. Using the other interior features
5
Inte
rior fe
■
Lighting conditions of operation indicator light
*
: Depending on the portable device, there are cases where the operation indicator
light will continue being lit up orange even after the charging is complete.
●
When the operation indicator light flashes
When an error occurs, the operation indicator light flashes an orange color.
Handle the error based on the following table.
■
The wireless charger can be operated when
The engine switch is in ACCESSORY or IGNITION ON mode.
■
Usable portable devices
Qi standard wireless charge standard can be used on compatible devices.
However, not all Qi standard devices and compatibility are guaranteed.
Starting with mobile phones and smart phones, it is aimed for low power electrically sup-
plied portable devices of no more than 5W.
Operation indicator light
Conditions
Turning off
When the Wireless charger power supply is off
Green (comes on)
On Standby (charging possible state)
When charging is complete
*
Orange (comes on)
When placing the portable device on the charging
area (detecting the portable device)
Charging
Operation indicator light
Suspected causes
Handling method
Flashing repeatedly once
every second (Orange)
Vehicle to charger commu-
nication failure.
Contact your Lexus dealer.
Repeatedly flashes
3 times continuously
(Orange)
A foreign substance is
between the portable device
and charge area.
Remove the foreign sub-
stance from between por-
table device and the
charge area.
The portable device is out of
sync due to the device being
shifted from its position.
Place the portable device
near the center of the
charge area.
Repeatedly flashes
4 times continuously
(Orange)
Temperature rising within
the wireless charger.
Stop charging at once and
start charging again after
for a while.
444
5-6. Using the other interior features
■
When covers and accessories are attached to portable devices
Do not charge in situations where cover and accessories not able to handle Qi are
attached to the portable device. Depending on the type of cover and accessory, it may
not be possible to charge. When charging is not performed even with the portable
device placed on the charge area, remove the cover and accessories.
■
While charging, noise enters the AM radio
Turn off the wireless charger and confirm that the noise has decreased. If the noise
decreases, continuously pushing the power supply switch of the wireless charger for 2
seconds, the frequency of the charger can be changed and the noise can be reduced.
Also, on that occasion, the operation indicator light will flash orange 2 times.
■
Important points of the wireless charger
●
If the electronic key cannot be detected within the vehicle interior, charging cannot be
done. When the door is opened and closed, charging may be temporarily suspended.
●
When charging, the wireless charging device and portable device will get warmer,
however this is not a malfunction.
When a portable device gets warm while charging, charging may stop due to the pro-
tection function on the portable device side. In this case, when the temperature of the
portable device drops significantly, charge again.
■
Operation sounds
When the power supply is turned on, while searching for the portable device a sound will
be produced, however this is not a malfunction.
446
447
5-6. Using the other interior features
5
Inte
rior fe
WARNING
■
Caution while driving
When charging a portable device, for safety reasons, the driver should not operate the
portable device while driving.
■
Caution regarding interference with electronic devices
People with implantable cardiac pacemakers, cardiac resynchronization therapy-
pacemakers or implantable cardioverter defibrillators, as well as any other electrical
medical device, should consult their physician about the usage of the wireless charger.
The operations of the wireless charger may have an affect on medical devices.
■
To prevent damage or burns
Observe the following precautions.
Failure to do so may result in a possibility of equipment failure and damage, catch fire,
burns due to overheat.
●
Do not insert any metallic objects between the charging area and the portable device
while charging
●
Do not attach stickers, metallic objects, etc., to the charger area or portable device
●
Do not cover with cloth, etc., and charge
●
Do not charge portable devices other than designated
●
Do not attempt to dismantle for disassembly or modifications
●
Do not hit or apply a strong force
448
5-6. Using the other interior features
WARNING
■
Conditions in which the function may not operate correctly
In the following conditions, the wireless charger may not operate correctly
●
The portable device is fully charged
●
There is foreign matter between the charge area and portable device
●
The temperature of the portable device gets higher from charging
●
The charging surface of the portable device is facing up
●
The placement of the portable device is out of alignment with the charge area
●
Near a TV tower, electric power plant, gas station, radio station, large display, airport
or other facility that generates strong radio waves or electrical noise
●
When the electronic key is in contact with, or is covered by the following metallic
objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
●
When other wireless keys (that emit radio waves) are being used nearby
In addition, excluding the above-mentioned, when the charger does not perform nor-
mally or the operation indicator light is flashing continuously, it is considered that the
wireless charger is malfunctioning. Contact your Lexus dealer.
■
To prevent failure or damage to data
●
Do not bring magnetic cards, such as credit cards, or magnetic recording media, etc.,
close to the charger while charging, otherwise, data may disappear under the influ-
ence of magnetism. Also, do not bring precision instruments such as wrist watches,
etc., close to the charger, as such objects may break.
●
Do not leave portable devices in the cabin. The temperature inside the cabin may
become high, when under the sun, and cause damage to the device.
■
To prevent battery discharge
When the engine is stopped, do not use the wireless charger for a long time.
449
5-6. Using the other interior features
5
Inte
rior fe
Fold down the armrest for use.
Armrest
NOTICE
To prevent damage, do not apply too much load on the armrest.
450
5-6. Using the other interior features
Pull the tab of the rear door sunshade
and hook the shade on using the
anchor.
To retract the rear door sunshade,
unhook the shade and retract it slowly.
The coat hooks are provided with the
second seat assist grips.
Rear door sunshades
NOTICE
To ensure normal operation of the rear door sunshade, observe the following precau-
tions.
●
Do not place anything where it may hinder the opening/closing of the sunshade.
●
Do not attach anything to the rear door sunshade.
●
Do not retract the rear door sunshade at an angle.
Coat hooks
WARNING
Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS cur-
tain shield airbags deploy, these items may become projectiles, causing death or seri-
ous injury.
451
5-6. Using the other interior features
5
Inte
rior fe
An assist grip (Type A) can be used to support your body while sitting on the seat.
An assist grip (Type B) can be used when getting in or out of the vehicle and oth-
ers.
Assist grip (Type A)
Assist grip (Type B)
Assist grips
1
2
WARNING
Do not use the assist grip (Type A) when getting in or out of the vehicle or rising from
your seat.
NOTICE
To prevent damage, do not hang heavy objects or put a heavy load on the assist grip.
452
5-6. Using the other interior features
Garage door opener
The HomeLink
®
wireless control system in your vehicle has 3 buttons which can
be programmed to operate 3 different devices. Refer to the programming meth-
ods on the following pages to determine the method which is appropriate for the
device.
HomeLink
®
indicator light
Garage door operation indicators
HomeLink
®
icon
Illuminates while HomeLink
®
is operat-
ing.
Buttons
■
Before programming HomeLink
®
●
During programming, it is possible that garage doors, gates, or other
devices may operate. For this reason, make sure that people and objects
are clear of the garage door or other devices to prevent injury or other
potential harm.
●
It is recommended that a new battery be placed in the remote control
transmitter for more accurate programming.
●
Garage door opener motors manufactured after 1995 may be equipped
with rolling code protection. If this is the case, you may need a stepladder
or other sturdy, safe device to reach the “Learn” or “Smart” button on the
garage door opener motor.
The garage door opener can be programmed to operate garage doors, gates,
entry doors, door locks, home lighting systems, security systems, and other
devices.
Programming HomeLink
®
1
2
3
4
453
5-6. Using the other interior features
5
Inte
rior fe
■
Programming the HomeLink
®
Steps through must be performed within 60 seconds, otherwise the
indicator light will stop flashing and programming will not be able to be com-
pleted.
Press and release the HomeLink
®
button you want to program and check
that the HomeLink
®
indicator light flashes (orange).
Point the remote control transmit-
ter for the device at the rear view
mirror, 1 to 3 in. (25 to 75 mm)
from the HomeLink
®
buttons.
Keep the HomeLink
®
indicator light
in view while programming.
Program a device.
Programming a device other
than an entry gate (for U.S.A.
owners)
Press and hold the remote control
transmitter button until the
HomeLink
®
indicator light
changes from slowly flashing
orange to rapidly flashing green
(rolling code) or continuously lit
green (fixed code), then release
the button.
Programming an entry gate (for U.S.A. owners)/Programming a device
in the Canadian market
Press and release the remote control transmitter button at 2 second inter-
vals, repeatedly, until the HomeLink
®
indicator light changes from slowly
flashing (orange) to rapidly flashing (green) (rolling code) or continuously
lit (green) (fixed code).
Test the HomeLink
®
operation by pressing the newly programmed button
and observing the indicator light:
●
Indicator light illuminates: Programming of a fixed code device has com-
pleted. The garage door or other device should operate when a Home-
Link
®
button is pressed and released.
1
3
1
2
3
4
454
5-6. Using the other interior features
●
Indicator light flashes rapidly: The garage door opener motor or other
device is equipped with a rolling code. To complete programming, firmly
press and hold the HomeLink
®
button for 2 seconds then release it.
●
If the garage door or other device does not operate, proceed to “Pro-
gramming a rolling code system”.
Repeat the steps above to program another device for any of the remaining
HomeLink
®
buttons.
■
Programming a rolling code system
2 or more people may be necessary to complete rolling code programming.
Locate the “Learn” or “Smart”
button on the garage door
opener motor in the garage.
This button can usually be found
where the hanging antenna wire is
attached to the unit. The name and
color of the button may vary by man-
ufacturer. Refer to the owner’s man-
ual supplied with the garage door
opener motor for details.
Press and release the “Learn” or
“Smart” button.
Perform within 30 seconds
after performing .
Press and hold the desired
HomeLink
®
button (inside the
vehicle) for 2 seconds and
release it. Repeat this sequence
(press/hold/release) up to 3
times to complete programming.
If the garage door opener motor
operates when the HomeLink
®
button is pressed, the garage
door opener motor recognizes
the HomeLink
®
signal.
5
1
2
3
2
3
455
5-6. Using the other interior features
5
Inte
rior fe
■
Enabling 2-way communication with a garage door (only available for com-
patible devices)
When enabled, 2-way communication allows you to check the status of the
opening and closing of a garage door through indicators in your vehicle.
2-way communication is only available if the garage door opener motor used
is a compatible device. (To check device compatibility, refer to www.Home-
Link.com.)
Within 5 seconds after programming the garage door opener has been
completed, if the garage door opener motor is trained to HomeLink
®
,
both garage door operation indicators will flash rapidly (green) and the
light on the garage door opener motor will blink twice, indicating that 2-
way communication is enabled.
If the indicators do not flash, perform and within the first 10 presses of
the HomeLink
®
button after programming has been completed.
Press a programmed HomeLink
®
button to operate a garage door.
Within 1 minute of pressing the HomeLink
®
button, after the garage door
operation has stopped, press the “Learn” or “Smart” button on the garage
door opener motor. Within 5 seconds of the establishment of 2-way com-
munication with the garage door opener, both garage door operation indi-
cators in the vehicle will flash rapidly (green) and the light on the garage
door opener motor will blink twice, indicating that 2-way communication is
enabled.
■
Reprogramming a single HomeLink
®
button
When the following procedure is performed, buttons which already have
devices registered to them can be overwritten:
With one hand, press and hold the desired HomeLink
®
button.
When the HomeLink
®
indicator starts flashing (orange), continue to hold
the HomeLink
®
button and perform “Programming HomeLink
®
”
(it
takes 20 seconds for the HomeLink
®
indicator to start flashing).
Press the appropriate HomeLink
®
button. The HomeLink
®
indicator light
should turn on.
Operating HomeLink
®
1
2
3
2
3
1
2
1
456
5-6. Using the other interior features
The status of the opening and closing of
a garage door is shown by the indica-
tors.
Opening
Closing
This function is only available if the
garage door opener motor used is a
compatible device. (To check device
compatibility, refer to www.Home-
Link.com.)
The indicators can operate within approximately 820 ft. (250 m) of the
garage door. However, if there are obstructions between the garage door and
the vehicle, such as houses and trees, feedback signals from the garage door
may not be received.
To recall the previous door operation status, press and release either Home-
Link
®
buttons
and
or
and
simultaneously. The
last recorded status will be displayed for 3 seconds.
Press and hold the 2 outside buttons for
10 seconds until the HomeLink
®
indi-
cator light changes from continuously
lit (orange) to rapidly flashing (green).
If you sell your vehicle, be sure to erase
the programs stored in the HomeLink
®
memory.
Garage door operation indicators
1
2
Color
Status
Orange (flashing)
Currently opening/closing
Green
Opening/closing has completed
Red (flashing)
Feedback signals cannot be received
Erasing the entire HomeLink
®
memory (all three codes)
457
5-6. Using the other interior features
5
Inte
rior fe
■
Codes stored in the HomeLink
®
memory
●
The registered codes are not erased even if the battery cable is disconnected.
●
If learning failed when registering a different code to a HomeLink
®
button that already
has a code registered to it, the already registered code will not be erased.
■
Before programming
●
Install a new battery in the transmitter.
●
The battery side of the transmitter must be pointed away from the HomeLink
®
.
■
Certification for the garage door opener
■
When support is necessary
Visit on the web at www.homelink.com/lexus or call 1-800-355-3515.
458
5-6. Using the other interior features
WARNING
■
When programming a garage door or other remote control device
The garage door or other device may operate, so ensure people and objects are out of
danger to prevent potential harm.
■
Conforming to federal safety standards
Do not use the HomeLink
®
compatible transceiver with any garage door opener or
device that lacks safety stop and reverse features as required by federal safety stan-
dards.
This includes any garage door that cannot detect an interfering object. A door or
device without these features increases the risk of death or serious injury.
■
When operating or programming HomeLink
®
Never allow a child to operate or play with the HomeLink
®
buttons.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст