Lexus UX 300e (2022 year). Manual in english — page 7

126

2-2. Charging

Insert the DC charging connector
into the DC charging inlet.

When inserting the DC charging connec-

tor into the DC charging inlet, make sure

that the identification symbols are the

same.
The DC charging connector shape and

treatment will differ depending on the type

of DC charger. Perform the operations in

accordance to handling procedures of the

DC charger.

Operate the DC charger and start
the charging.

Follow the handling procedures of the DC

charger to start charging.
Charging starts after a system check is

done.
Stop the charging in accordance to the

handling procedures of the DC charger

when it is desired to interrupt the DC

charging.

Charging time



P.109

Charging time may increase when



P.110

If a message indicating vehicle error on

the DC charger side is displayed

Even if a message indicating vehicle error

on the DC charger side (ex. vehicle error

found, vehicle error occurred, etc.) is dis-

played, there is no vehicle fault but possibly

a communication error between the DC

charger and vehicle. In this case, there may

be a terminal damage (bad contact) in the

DC charging connector. If there is no error

with the vehicle, contact the facility man-

ager of the DC charger.

The charging time displayed on the DC

charger

Depending on the type of the DC charger,

the charging time displayed on the DC

charger may be longer than normal. This is

not a malfunction.

During DC charging

The current charging condition can be

checked on the multi-information display.

The actual charging time may differ from

that displayed on the DC charger during

charging.

There may be occasions the radio cannot

be heard due to noise occurrence during

DC charging

The charging may stop before reaching

the upper limit of the charge capacity,

due to the remaining charge of the trac-

tion battery, the outside temperature,

etc., when charging starts.

It is recommended to avoid frequent DC

charging to prevent a decline in the trac-

tion battery capacity.

Quickly move from the DC charging

space for other users after the DC

charging is completed.

Changing the “Charging Limit” settings



P.120

127

2-2. Charging

ect
ric V
eh

icle

If “Check Charging System Close

Charging Port Lid See Owner’s Man-

ual” is displayed on the multi-informa-

tion display

After DC charging, the following may

occur if the system check after the DC

charging is not completed as normal.

The EV system can not be started.

The EV system can be started but DC

charging and AC charging can not be

done.

Perform a system check with the following
procedures.

Be sure to engage the parking brake

and then turn the power switch off.

Install the DC charging inlet cap, close

the DC charging port lid.

Check if “Checking Charging System”

is displayed on the multi-information

display when the power switch is turned

to ON.

Do not open the DC charging port lid while

the charging system is checking.
When the system check is completed, the

power switch automatically turns off.

Press the power switch while depress-

ing the brake pedal. The “READY” indi-

cator turns on.

Contact any authorized Lexus retailer or

Lexus authorized repairer, or any reliable

repairer if the charging system check is

done and the message on the multi-infor-

mation display does not go off.

WARNING

Warnings for DC charging

Be sure to observe the following when

using DC charging.
Failure to do so may cause an accident

that could lead to death or serious injury.

Check that the DC charger and DC

charging inlet are not damaged. If

there is any damage to the DC

charging inlet, do not perform a DC

charge and have it inspected immedi-

ately at any authorized Lexus retailer

or Lexus authorized repairer, or any

reliable repairer.

Do not touch the terminals of the DC

charging connector or inlet with

metallic sharp tips (wires and needles),

or allow a short circuit to occur with

foreign objects.

Do not insert anything other than the

DC charging connector into the DC

charging inlet.

Check that the DC charging cable is

not coiled up or pinned underneath

heavy objects.

When DC charging is interrupted, fol-

low the handling procedures of the

DC charger. Immediately stop the DC

charging when there is an outbreak of

heat, smoke, strange noises or smells,

etc., during charging.

Check that the DC charging connec-

tor and DC charging inlet do not have

foreign objects or snow or ice

attached to it. If anything is attached to

the inlet, be sure to completely remove

the material before connecting the

DC charging connector.

Do not charge the vehicle when there

is a possibility of lightning. If you notice

lightning while charging the vehicle, do

not touch the vehicle and the DC

charging cable.

128

2-2. Charging

Operate the DC charger and stop
the charging.

Remove the DC charging connec-
tor.

The DC charging connector shape and

treatment will differ depending on the type

of DC charger. Perform the operations in

accordance to handling procedures of the

DC charger.
Return the removed DC charging connec-

tor to its original position.

Attach the DC charging inlet cap
and close the DC charging port lid.

Align the horizontal sections of the cap

and inlet, and then insert the cap straight

into the inlet.

If the DC charging connector cannot be

unlocked

The DC charging connector is locked by

the DC charger. Operation of the emer-

gency release lever cannot unlock the

WARNING

Do not get the DC charging inlet ter-

minals wet.

Be sure the DC charging inlet makes

direct contact with the DC charging

connector. Do not connect conversion

adapters, extension cords, etc.,

between the DC charging connector

and DC charging inlet.

Close the hood when using DC

charging. The cooling fans may sud-

denly start to run. Keep hands and

clothing (especially a tie, a scarf or a

muffler) away from the fans. Failure to

do so may cause the hands or clothing

to be caught, resulting in serious injury.

When connecting the DC charging

connector

Follow the handling procedures of the

DC charger to connect the DC charging

connector. If the connector is not con-

nected properly, the system cannot rec-

ognize the connection, and it may be

possible to start the EV system.
After charging is completed, make sure

to remove the DC charging connector

from the DC charging inlet before start-

ing the EV system.
If the vehicle is started off with the con-

nector still connected, it could lead to an

accident, possibly resulting in death or

serious injury.

NOTICE

When using DC charging

Make sure to follow the handling proce-

dures of the DC charger. If the proce-

dures are not followed properly, the

vehicle and the DC charger may be

damaged.

After charging

129

2-2. Charging

ect
ric V
eh

icle

DC charging connector.

The DC charging connector cannot be

removed during DC charging. Stop the

DC charging when it is necessary to

remove the DC charging connector. The

DC charging connector can be removed

when the DC charging is stopped.

If the DC charging connector cannot be

removed even if the DC charging is

stopped, there may be a malfunction with

the DC charger, contact the facility man-

ager of the DC charger.

After DC charging

Even if the traction battery is charged to the

upper limit value that is set, the level of

charge displayed on the DC charger may

be lower than the actual one.

When registering the charging sched-
ule, the following settings can be
changed.

Select the charging mode

One of the following two charging
modes can be selected.

: There might be a slight error in the tim-

ing when charging starts due to the
capacity of the traction battery.

: Charging schedule function is per-

formed in accordance with the clock.

NOTICE

Caution after DC charging

Be sure to attach the DC charging

inlet cap to the DC charging inlet and

then close the DC charging port lid

after removing the DC charging con-

nector from the inlet. If the DC

charging inlet cap is not attached, for-

eign materials may get into the inlet

and the EV system may be malfunc-

tioning.

Using the charging schedule
function (AC charging)

AC charging can be performed at
the desired time by registering the
charging schedule. Also, it is possi-
ble to set the schedule to one’s
preferences, such as having
charging complete by a certain
departure time or be performed at
the same time on certain days.

Settings of the charging sched-
ule function

Charging

mode

Operation description

“Start”

Starts charging at the set time

and completes charging when
fully charged.

“Depar-

ture”

Starts charging to complete at
the set time.

*3, 4

When this setting is selected,
the air conditioning linked
function can be used.

130

2-2. Charging

Before registering the charging sched-
ule, check and set the clock to the
proper time.

: If the system determines that charging

cannot be completed by the set depar-
ture time, it will start charging. Check
the charging schedule.

: If the outside temperature changes sud-

denly or the state of the power source
being used is changed during charging,
the system may not complete the
charging as estimated.

Repeated setting

The periodic charging schedule can be
set by selecting your desired day of the
week.
Charging schedule can be performed
only once if the days are not selected.

Air conditioning-linked setting

When the charging mode is set to
“Departure”, the vehicle air condition-
ing system can be set to automatically
operate

according to the set time.

By adjusting the cabin temperature in
advance and matching it with the depar-
ture time, passengers can enjoy a pleasant
interior immediately after entering the
vehicle.

: Operation starts approximately 20 min-

utes before the set departure time.

Turning “Charge Now” on and off

If even one charging schedule is regis-
tered, charging does not start until the
set time, even if the AC charging cable
is connected to the vehicle. To start
charging immediately without chang-
ing the charging schedule setting, turn
“Charge Now” on to temporarily can-

cel the charging schedule and enable
charging after connecting the AC
charging cable.

: If the charging connector is unlocked

during charging while the charging
schedule is registered and “Charge
Now” is on, “Charge Now” turns off.

Changing “Next Event”

It is possible to temporarily set the time
of the next charging schedule without
changing the registered repeated set-
ting.

: The “Next Event” refers to the closest

charging schedule from the current
time among the registered charging
schedules. Charging schedule is per-
formed based on the “Next Event”.

: When “Next Event” is changed, the cur-

rent charging schedule will be tempo-
rarily ignored and charging will not be
performed until the time specified by
“Next Event”. (For example, when
“Next Event” is set for 2 days later, even
if items are registered on the charging
schedule, charging will not be per-
formed until the time specified by “Next
Event”.)

Charging schedule settings

A maximum of 15 charging schedules can

be registered.

Charging schedule function

The charging schedule function can not be

used when using DC charging.

To make sure that the charging sched-

ule function operates correctly

Check that the following conditions are

met:

The clock is adjusted to the proper time

and the day of the week is proper

131

2-2. Charging

ect
ric V
eh

icle

The power switch is OFF

After registering the charging schedule,

connect the AC charging cable. When

the AC charging cable is connected, the

charging start time is determined based

on the charging schedule at the time.

The AC charging indicator flashes after

the AC charging cable is connected

(



P.91)

Do not use an electrical socket that has

power cut off function (including off timer

function). Only use an electrical socket

that constantly supplies power. If the

electrical socket is cut off due to a off

timer function, etc., charging may not be

performed appropriately during the set

time.

The traction battery is not fully charged.

The automatic adjustment of the clock by

GPS is set to “On”. If the clock has been

adjusted in an area where a GPS signal

cannot be received, set the automatic

adjustment of the clock by GPS to “On”

in an area where a GPS signal can be

received.

For details regarding GPS, refer to the
“NAVIGATION AND MULTIMEDIA
SYSTEM OWNER’S MANUAL”.

When charging is performed regardless

of the charging schedule

When the charging schedule is on standby,

if a temporary cancelation operation is per-

formed, charging schedule will be canceled

and charging will begin immediately.

When the AC charging cable remains

connected to the vehicle

Even if multiple consecutive charging

schedules are registered, the next charge

will not be carried out according to the

schedule until the AC charging cable is

removed and reconnected after charging

completes. Also, when the traction battery

is fully charged, charging according to the

schedule will not be performed.

Air conditioning-linked setting

When the air conditioning-linked setting

is turned on, the air conditioning operates

until the set departure time. Therefore,

depending on the air conditioning elec-

tricity consumption, charging may not be

completed by the set departure time.

If the traction battery is fully charged,

charging will not be carried out, even if

the charging schedule is registered.

However, if Air conditioning-linked set-

ting is turned on, the air conditioning will

operate only once when it nears the time

set in “Departure”. If this occurs, the air

conditioning will consume electricity and

the remaining charge of the traction bat-

tery when departing may be decreased.

When the doors are unlocked, the air

conditioning system does not operate.

When charging schedule settings are

ignored

When the following operations are per-

formed while the charging schedule is on

standby, charging schedule is temporarily

canceled and charging is started.

When the Remote Air Conditioning Sys-

tem (



P.355) is operated

When “My Room Mode” is activated

(



P.139)

When setting “Charge Now” to “On”

(



P.135)

When an operation that temporarily can-

cel the charging schedule is performed

(



P.120)

Effects of outside temperature

When the charging mode is set to “Depar-

ture”, charging schedule may be ignored

due to the outside temperature and

charging may start.

Traction battery cooler (



P.111)

When charging is performed using the

charging schedule, the traction battery

cooling function may operate according to

the temperature of the traction battery.

When the charging mode is set to “Start”,

cooling starts at the set charging start

time.

When the charging mode is set to

“Departure”, cooling starts approxi-

mately 30 minutes before the charging

132

2-2. Charging

start time. However, if there is no time to

complete charging according to the

charging schedule, the traction battery

cooling time may be shortened and trac-

tion battery cooler may not operate.

The meter control switches are used to
change the charging schedule function
settings.

Meter control switches

Multi-information display

Registering the charging schedule

Press

of the meter con-

trol switches to select

on the

multi-information display.

Press

of the meter con-

trol switches to select “Vehicle Set-
tings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Settings”, and then press “OK”.

The “Charging Settings” display will be dis-

played.

Press

of the meter con-

trol switches to select “Charging
Schedule” and then press “OK”.

The “Charging Schedule” display will be

displayed.

Press

of the meter con-

trol switches to select “Scheduled
Events” and then press “OK”.

The “Scheduled Events” display will be dis-

played.

Select “Add”, and then press “OK”.

The “Charging Mode” display will be dis-

played.

Setting “Charging Schedule” on
the multi-information display

A
B

133

2-2. Charging

ect
ric V
eh

icle

Press

of the meter con-

trol switches to select item and then
press

to change the

charging mode/time settings.

Set the desired charge mode, as well as the

charging start (or Departure) time.
When the settings have been changed,

press “OK”.
Set the time that is desired to start the

charging when charge mode is “Start” and

the desired completion time when the

mode is “Departure”.
When the charging mode is set to “Depar-

ture”, the “Climate Prep” display will be

displayed. When the charging mode is set

to “Start”, the “Repeat” display (step

) will

be displayed.

Press

of the meter con-

trol switches when operating the air
conditioner, select “Yes” and then
press “OK”.

The “Repeat” display will be displayed.

Press

of the meter con-

trol switches, select the day desired
to activate the repeated setting,
and press “OK”.

Each time “OK” is pressed, the repeat set-

tings switches between on and off.
Charging schedule is done repeatedly on

the day selected.
It is also possible to turn the repeated set-

ting to “On” for multiple days.
If no days are set to “On”, charging is only

done once according to the charging

schedule within 24 hours.
When setting are complete, select “Done”

and then press “OK”.
A display that confirms the settings are

saved is displayed.

134

2-2. Charging

Press

of the meter con-

trol switches, select “Save” and
press “OK”.

The setup contents are saved.
If it is desired to change the setting details,
press “

” and change the operation

settings.
After completing the settings, when the

AC charging cable is connected to the

vehicle, the charging schedule is done in

accordance with the setting details.

Changing the registered charging
schedules

The registered charging schedules can
be turned on/off, deleted or modified.

Press

of the meter con-

trol switches to select

on the

multi-information display.

Press

of the meter con-

trol switches to select “Vehicle Set-
tings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Settings”, and then press “OK”.

The “Charging Settings” display will be dis-

played, which displays a list of the regis-

tered charging schedules.

Press

of the meter con-

trol switches to select “Charging
Schedule” and then press “OK”.

The “Charging Schedule” display will be

displayed.

Press

of the meter con-

trol switches to select “Scheduled
Events” and then press “OK”.

The “Scheduled Events” display will be dis-

played.

Press

of the meter con-

trol switches, select the line of the
settings where the contents are
desired to be changed, and then
press and hold “OK”.

135

2-2. Charging

ect
ric V
eh

icle

The “Edit Event” display will be displayed.

Press

of the meter con-

trol switches, select the item to
operate and perform each neces-
sary operation.



ON/OFF

Each time “OK” of the meter control
switch is pressed on the “Scheduled
Events” display, the selected charging
schedule switches between “On” and
“Off”.
When set to OFF, a charging schedule is
ignored and charging according to the
schedule is not performed.

When

is pressed, setup is completed.



“Edit”

Change the desired settings as described
starting from step

of the Registering the

charging schedule procedure. (



P.132)

Press

of the meter control

switches, select “Save” and press “OK” to
save the settings.

Press the

switch to return to the pre-

vious display.



“Delete”

When “OK” is pressed on the meter con-
trol switches, a deletion confirmation will
be displayed.

Press

of the meter control

switches, select “Yes” and then press “OK”
to delete the selected charging schedule.

Press the

switch to return to the pre-

vious display.
To cancel deletion of the registered con-
tents, select “No” and then press “OK”.

Setting “Charge Now” to “On”

The “Charge Now” setting can be
changed by performing one of the two
following procedures.

136

2-2. Charging



Operation on the “Charging Sched-
ule” display

Press

of the meter con-

trol switches to select

on the

multi-information display.

Press

of the meter con-

trol switches to select “Vehicle Set-
tings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Settings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Schedule” and then press “OK”.

The “Charging Schedule” display will be

displayed on the multi-information display.

Press

of the meter con-

trol switches to select “Charge
Now”, and then press “OK”.

Each time “OK” is pressed, “Charge Now”

switches between “On” and “Off”.



Operation on the ending display

The “Next Event” display will be dis-
played after the power switch is turned
off.

Turn the power switch off.

The ending display will be displayed on the

multi-information display.

Press “OK” to set “Charge Now” to
“On”.

Each time “OK” is pressed, “Charge Now”

switches between “On” and “Off”.

After setting operations are complete,

charging starts when the AC charging

cable is connected. (



P.116)

Changing “Next Event”

: When “Charge Now” is set to “On” or

My Room Mode is in use (



P.139) etc.,

the registered “Next Event” cannot be
changed.

Press

of the meter con-

trol switches to select

on the

multi-information display.

Press

of the meter con-

trol switches to select “Vehicle Set-
tings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Settings” and then press “OK”.

Press

of the meter con-

trol switches to select “Charging
Schedule” and then press “OK”.

The “Charging Schedule” display will be

displayed on the multi-information display.

137

2-2. Charging

ect
ric V
eh

icle

Press

of the meter con-

trol switches to select “Next Event”,
and then press “OK”.

The “Next Event” display will be displayed.

Press

of the meter con-

trol switches to select “Yes”, and
then press “OK”.

A display that confirms changes for the

“Next Event” will be displayed.
When canceling changes, Select “No” and

then press “OK”.

Press

of the meter con-

trol switches to select “OK”, and
then press “OK”.

The “Charging Mode” display will be dis-

played.

Press

to return to the previous dis-

play.

Press

of the meter con-

trol switches, select the item to
change, press

and

change the settings.

138

2-2. Charging

When setting are complete, press
“OK”.

A display to confirm the setup saving will

be displayed.

Press

of the meter control

switches to select “Save”, and then press

“OK” to save the contents that were setup.
If it is desired to change the setup contents,
press

and change the operation

setup.

The charging schedule setting display

will be suspended when

It is necessary for a message with a

higher priority than the charging sched-

ule setting to be displayed.

The power switch is turned off before the

settings are confirmed.

The vehicle is started off.

“Next Event”

Even after charging is performed according

to the “Next Event” schedule, the “Next

Event” displayed on the multi-information

display will not change until the AC

charging cable is removed after charging

completes.

To return to original setting after chang-

ing “Next Event” setting

Turning the setting of “Charge Now” on

and then off can return the setting of “Next

Event” to its original setting.

When “Next Event” is changed while

charging

When the charging mode is “Departure”,

the current charging is interrupted or

continued depending on the remaining

time until the charging is completed.

When the charging mode is “Start”, the

current charging is interrupted, the next

charging will start at the set time.

When the power switch is turned off

When the power switch is turned off, the

next charging schedule will be displayed on

the ending display and the registered con-

Setting

Operation

Charge

mode/Time

Operate , ,

and

of the meter control

switches to set the
charging mode (“Start” or
“Departure”) and charging
start (or departure) time.
When setting are com-
plete, press “OK”.

Day

Operate

of the

meter control switches to
select the day to perform
charging according to the
schedule.
When setting are com-
plete, press “OK”.

Air condi-

tioner linked

This can be set when the
charging mode is set to
“Departure”. To activate
the air conditioner link,
press

of the

meter control switches to
select “Yes” and then press
“OK”.

139

2-2. Charging

ect
ric V
eh

icle

tents can be checked.
Also, the ending display may not be dis-

played during charging.

Connect the charge cable to the
vehicle to start charging.

AC Charging:



P.116

DC Charging:



P.125

Turn the power switch to ON while
charging.

The My Room Mode settings is automati-

cally displayed on the multi-information

display.

Press

of the meter con-

trol switches to select “Yes”, and
then press “OK”.

My Room Mode is started and it is possible

to use the air conditioning system, audio

system, etc.
Select “No” and press “OK” when My

Room Mode is not being used.

To disable My Room Mode, turn the

power switch off.

NOTICE

While setting the charging schedule

To prevent 12-volt battery discharge,

ensure that the EV system is operating

while setting the charging schedule on

the multi-information display.

Using My Room Mode

When the charging cable is con-
nected to the vehicle, electrical
components such as the air condi-
tioning system and audio system
can be used by the power supply
from an external power source.

Starting My Room Mode

140

2-2. Charging

My Room Mode will automatically be off

when DC charging is completed.

When starting My Room Mode, the
electric power balance will be auto-
matically displayed on the multi-infor-
mation display, and an approximation
of the electricity balance (the balance
between the amount of electricity pro-
vided and electricity consumed) during
My Room Mode can be checked.

Discharging (-)

Charging (+)

The size of the arrow symbol changes
depending on the power supply and elec-
tricity consumption amounts.
If the electricity consumption is more than
the power supply,

is displayed more

than .
If the power supply and electricity con-
sumption amounts are equal,

and

are displayed as the same size.

Meter display while charging

After turning the power switch to ON while

charging, the power switch automatically

turns off if My Room Mode is not selected

within approximately 100 seconds.

When using My Room Mode the follow-

ing may occur

When the remaining charge of the trac-

tion battery drops to the lower limit, the

air conditioning system automatically

stops. In that case, the air conditioning

system can not operate until the remain-

ing charge of the traction battery

increases. Turn off the power switch

once, then use My Room Mode after the

remaining charge of the traction battery

increases.

If the doors are unlocked while using My

Room mode, the AC charging connector

will be unlocked and the My Room mode

will be stopped. To use My Room mode

again, perform the operation to start it.

(



P.139) In addition, when using AC

charger at the public charging station, it is

necessary to perform the operation to

start the charger before using My Room

mode.

The charging time of the traction battery

gets longer.

Noise may be heard from the radio

depending on conditions of the radio

wave.

Fan noises may be heard from under the

floor.

The surrounding area of the onboard

traction battery charger in the motor

compartment may become hot.

The electric power steering system warn-

ing light (yellow) may turn on, but this is

not a malfunction.

Registering the charging schedule

(



P.132)

When My Room Mode starts while a

charging schedule is on standby, the

charging schedule settings are disable and

charging starts immediately.

Using My Room Mode with the traction

battery fully charged

A warning message “Charging Port Lid is

Open” will be displayed on the multi-infor-

Display information for electric
power balance during My Room
Mode

A
B

141

2-2. Charging

ect
ric V
eh

icle

mation display, if the power switch is turned

on when the traction battery is fully charged

and the AC charging connector is con-

nected.

In that case, by pressing the

of meter

control switches, the My Room Mode set-

tings screen will be displayed and “Yes” can

be selected.
When My Room Mode is used with the

traction battery fully charged, electricity of

the traction battery will be consumed. In

that case, perform the charging again.

Warning message display

When trying to start My Room Mode or My Room Mode is being used, if a message is dis-

played on the multi-information display, refer to the corresponding table and perform the

appropriate correction procedures.

: During My Room Mode, the information for electric power balance can be checked on

the multi-information display.

Message

Correction procedure

“Traction Battery is too Low
for “My Room Mode””

There is no remaining charge of the traction battery to start
My Room Mode. Wait until the remaining charge of the
traction battery increases, start the My Room Mode.

““My Room Mode” has
stopped due to low traction
battery level”

The remaining charge of the traction battery is insufficient.
Stop using the My Room Mode and charge the traction
battery.

““My Room Mode” will stop
when traction battery level is
too low Reduce power usage
to continue using “My Room
Mode””

The electricity consumption of the vehicle is more than the
charge amount for the traction battery, thus the remaining
charge of the traction battery is low.

• If the electricity consumption of the vehicle can not be

improved, the My Room Mode will be off.

• When My Room Mode continuation is desired, turn off

the air conditioning system, audio system, etc., to
increase the remaining charge of the traction battery.

Была ли эта страница вам полезна?

Да!Нет

1 посетитель считают эту страницу полезной.

Lexus UX 300e (2022 year). Manual in english — page 7

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.