Lexus RX350 L (2022 year). Manual in english — page 6
105
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
for the operation to occur.
Kick sensor
Hands Free Power Back Door
operation detection area
3
When the kick sensor detects that
your foot is pulled back, a buzzer
will sound and the power back door
will automatically fully open/close.
If kick operation is performed again in the
middle of back door operating, the opera-
tion will stop.
■
Hands free close & lock function*
(vehicles with Hands Free Power
Back Door)
*
: This setting can be customized by your
Lexus dealer.
If the power back door is closed using a
Hands Free Power Back Door close
operation, all of the doors will be
locked at the same time.
A different buzzer than the normal one will
sound before the power back door begins
to close. The door lock operation signals
will operate to indicate that the power back
door has closed and all of the doors have
locked simultaneously.
If a Hands Free Power Back Door opera-
tion is performed while the power back
door is operating, the power back door will
stop.
If a Hands Free Power Back Door opera-
tion is performed again, the power back
door will open.
■
Luggage compartment lights
●
The luggage compartment lights turn on
when the back door is opened.
●
When the engine switch is turned off, the
lights will go off automatically after 20
minutes.
■
Power back door operating conditions
If the following conditions are met with the
power back door operation enabled, the
power back door can be opened and
closed automatically.
●
When an electronic key is being carried
and the back door opener switch is
pressed
*
●
When the wireless remote control is
used
*
●
When the engine switch is in IGNITION
ON mode, the vehicle speed must be
lower than 2 mph (3 km/h) and one of
the following conditions must be met in
addition to the above conditions:
• The parking brake is engaged.
• The brake pedal is depressed.
• The shift lever is in P.
*
: When the operation of the power back
door when it is locked has been disabled
by a customized setting, operate the
power back door after it has been
unlocked.
■
Close & lock function operating condi-
tions
This function can be operated when all of
the following conditions are met:
• An electronic key is not detected within
the vehicle.
• All of the doors other than the power
back door are closed.
• The engine switch is off.
■
Hands Free Power Back Door operating
conditions (if equipped)
●
The Hands Free Power Back Door (kick
sensor) setting is on.
A
B
106
3-2. Opening, closing and locking the doors
●
When an electronic key is carried within
the operation range.
■
Hands free close & lock function oper-
ating conditions (vehicles with Hands
Free Power Back Door)
This function can be operated when all of
the following conditions are met:
• The hands free close & lock function set-
ting is on.
• The Hands Free Power Back Door oper-
ating conditions are met.
• An electronic key is not detected within
the vehicle.
• All of the doors other than the power
back door are closed.
• The engine switch is off.
■
Back door closer
In the event that the power back door is left
slightly open, the back door closer will auto-
matically close it to the fully closed position.
●
The back door closer can function when
the engine switch is in any mode.
●
The power back door can be opened
using the back door opener switch even if
the back door closer is operating.
■
Operation of the power back door
●
When the power back door begins to
operate, the emergency flashers will flash
and a buzzer will sound.
●
When the power back door is disabled,
the power back door will not operate but
can be opened and closed manually.
●
The power back door turns to manual
operation when the back door opener
switch is pressed while the power back
door is in an automatic opening/closing
operation.
●
If anything obstructs the power back
door while opening, a buzzer will sound
and the power back door will stop imme-
diately. If anything obstructs the power
back door while closing, a buzzer will
sound and the power back door will auto-
matically move slightly in the opposite
direction and then stop.
■
Back door reserve lock function
This function reserves the locking of the
power back door when the power back
door is open. If the following operations are
performed, all of the doors except the
power back door will lock and then the
power back door will lock when it is com-
pletely closed.
1
Close all of the doors, except the power
back door.
2
Perform an automatic closing operation
of the power back door and lock the
doors using the wireless remote control
(
P.95) or smart access system with
push-button start (
power back door is closing.
Also, if the back door does not fully close
due to the operation of the jam protection
function, etc., while the back door is auto-
matically closing after a reserve lock opera-
tion is performed, the reserve lock function
is canceled and all the doors will unlock.
■
Situations in which the close & lock
function may not operate properly
In the following situations, the close & lock
function may not operate properly:
●
If the
switch on the lower part of the
power back door (
P.103) is pressed by
a hand which is holding an electronic key
●
If the
switch on the lower part of the
power back door (
P.103) is pressed
when the electronic key is in a bag, etc.
that is placed on the ground
●
If the
switch on the lower part of the
power back door (
P.103) is pressed
with the electronic key not near the vehi-
cle.
■
Situations in which the Hands Free
Power Back Door may not operate
properly (if equipped)
In the following situations, the Hands Free
Power Back Door may not operate prop-
erly:
●
When a foot remains under the rear
bumper
●
If the rear bumper is strongly hit with a
foot or is touched for a while
107
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
If the rear bumper has been touched for a
while, wait for a short time before
attempting to operate the Hands Free
Power Back Door again.
●
When standing excessively close to the
rear bumper
●
When an external radio wave source
interferes with the communication
between the electronic key and the vehi-
cle (
●
When the vehicle is parked near metal, or
an external radio wave or electrical noise
source which affects the sensitivity of the
Hands Free Power Back Door, such as a
pay parking spot, gas station, electrically
heated road, fluorescent light, or metal
plate
●
When the vehicle is near a TV tower,
electric power plant, radio station, large
display, airport or other facility that gen-
erates strong radio waves or electrical
noise
●
When a large amount of water is applied
to the rear bumper, such as when the
vehicle is being washed or in heavy rain
●
When mud, snow, ice, etc. is attached to
the rear bumper
●
When the vehicle has been parked for a
while near objects that may move and
contact the rear bumper, such as plants
●
When an accessory is installed to the rear
bumper
If an accessory has been installed, turn the
Hands Free Power Back Door (kick sen-
sor) operation setting off.
●
RX350L: When a tire other than the
spare tire is stored in the spare tire stor-
age area
■
Preventing unintentional operation of
the Hands Free Power Back Door (if
equipped)
When an electronic key is in the operation
detection area, the Hands Free Power Back
Door may operate unintentionally, so be
careful in the following situations:
●
When a large amount of water is applied
to the rear bumper, such as when the
vehicle is being washed or in heavy rain
●
When dirt is wiped off the rear bumper
●
When a small animal or small object, such
as a ball, moves under the rear bumper
●
When an object is moved from under the
rear bumper
●
If someone is swinging their legs while sit-
ting on the rear bumper
●
If the legs or another part of someone’s
body contacts the rear bumper while
passing by the vehicle
●
When the vehicle is parked near an elec-
trical noise source which affects the sen-
sitivity of the Hands Free Power Back
Door, such as a pay parking spot, gas sta-
tion, electrically heated road, or fluores-
cent light
●
When the vehicle is near a TV tower,
electric power plant, radio station, large
display, airport or other facility that gen-
erates strong radio waves or electrical
noise
●
When the vehicle is parked in a place
where objects such as plants are near the
rear bumper
●
If luggage, etc. is set near the rear
bumper
●
If accessories or a vehicle cover is
installed/removed near the rear bumper
●
When the vehicle is being towed
To prevent unintentional operation, turn the
Hands Free Power Back Door (kick sensor)
operation setting off.
■
When reconnecting the battery
To enable the power back door to operate
properly, close the power back door manu-
ally.
■
Jam protection function
Sensors are installed in the right and left
sides of the power back door. When the
door is automatically closing and the sen-
sors are pushed due to an object being
caught, etc., the jam protection function will
operate.
From that position the door will automati-
cally move a little in the opposite direction
and then the function will stop.
108
3-2. Opening, closing and locking the doors
■
If the power back door opener is inoper-
ative
The power back door can be unlocked from
the inside
1
Remove the cover.
To protect the cover, place a rag between
the flathead screwdriver and cover as
shown in the illustration.
2
Move the lever.
■
Customization
Some functions can be customized.
(
WARNING
■
Back door closer
●
In the event that the power back door
is left slightly open, the back door
closer will automatically close it to the
fully closed position. It takes several
seconds before the back door closer
begins to operate. Be careful not to get
fingers caught or anything else in the
power back door, as this may cause
bone fractures or other serious inju-
ries.
●
Use caution when using the back door
closer as it still operates when the
power back door system is disabled.
■
Power back door
Observe the following precautions when
operating the power back door.
Failure to do so may cause death or seri-
ous injury.
●
Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
●
If anyone is in the vicinity, make sure
they are safe and let them know that
the power back door is about to open
or close.
●
If the power back door system is dis-
abled while the power back door is
operating, the power back door will
stop operating. The power back door
must then be operated manually. Take
extra care in this situation, as the
power back door may open or close
suddenly.
109
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
WARNING
●
If the operating conditions of the
power back door (
P.105) are no lon-
ger met, a buzzer may sound and the
power back door may stop opening or
closing. The power back door must
then be operated manually. Take extra
care on an incline in this situation, as
the power back door may move sud-
denly.
●
On an incline, the power back door
may suddenly shut after it opens. Make
sure the power back door is fully open
and secure.
●
In the following situations, the power
back door may detect an abnormality
and automatic operation may be
stopped. In this case, the power back
door must then be operated manually.
Take extra care in this situation, as the
stopped power back door may sud-
denly open or close, causing an acci-
dent.
• When the power back door contacts
an obstacle
• When the battery voltage suddenly
drops, such as when the engine switch
is turned to IGNITION ON mode or
the engine is started during automatic
operation
●
If a bicycle carrier or similar heavy
object is attached to the power back
door, the power back door may not
operate, causing a malfunction, or the
power back door may suddenly shut
again after being opened, causing
someone’s hands, arms, head or neck
to be caught and injured. When install-
ing an accessory part to the power
back door, using a genuine Lexus part
is recommended.
■
Jam protection function
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
●
Never use any part of your body to
intentionally activate the jam protec-
tion function.
●
The jam protection function may not
work if something gets caught just
before the power back door fully
closes. Be careful not to get fingers
caught or anything else.
●
The jam protection function may not
work depending on the shape of the
object that is caught. Be careful not to
catch fingers or anything else.
■
Hands Free Power Back Door (if
equipped)
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
●
Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
●
Exhaust gasses cause the exhaust
pipes to become quite hot. When
operating the Hands Free Power Back
Door, be careful not to touch the
exhaust pipe.
●
Do not operate the Hands Free Power
Back Door if there is little space under
the rear bumper.
110
3-2. Opening, closing and locking the doors
NOTICE
■
Back door spindles
The power back door is equipped with
spindles
that hold the power back
door in place.
Observe the following precautions.
Failure to do so may cause damage to
the back door spindle
, resulting in
malfunction.
●
Do not attach any foreign objects, such
as stickers, plastic sheets, or adhesives
to the spindle rod.
●
Do not attach any accessories other
than genuine Lexus parts to the power
back door.
●
Do not place your hand on the spindle
or apply lateral forces to it.
■
To prevent back door closer malfunc-
tion
●
Do not apply excessive force to the
power back door while the back door
closer is operating. Applying excessive
force may cause the back door closer
to malfunction.
●
If the power back door is opened and
closed repeatedly in a short amount of
time, the back door closer may stop
operating. In this case, manually open
the power back door once and wait for
a while before attempting to close it
again.
A
A
■
To prevent malfunction of the power
back door
●
Make sure that there is no ice between
the power back door and frame that
would prevent movement of the power
back door. Operating the power back
door when excessive load is present
on the power back door may cause a
malfunction.
●
Do not apply excessive force to the
power back door while the power
back door is operating.
●
Take care not to damage the sensors
installed on the right and left edges of
the power back door (
P.107) with a
knife or other sharp object. If a sensor
is disconnected, the power back door
will not close automatically.
■
Close & lock function/Hands free
close & lock function
When closing the power back door using
the close & lock function/hands free
close & lock function, a different buzzer
than the normal one will sound before
the operation begins.
To check that the operation has started
correctly, check that a different buzzer
than the normal one has sounded.
Additionally, when the power back door
is fully closed and locked, operation sig-
nals will indicate that all of the doors have
been locked.
Before leaving the vehicle, make sure
that the operational signals have oper-
ated and that all of the doors are locked.
■
Hands Free Power Back Door pre-
cautions (if equipped)
The kick sensor is located behind lower
center part of the rear bumper. Observe
the following to ensure that the Hands
Free Power Back Door function operates
properly:
111
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
The power back door system can be
enabled/disabled on the multi-informa-
tion display. (
1
Press
or
of the meter con-
trol switches and select
.
2
Press
or
of the meter con-
trol switches, select the “Vehicle
Settings” and then press
.
3
Press
or
of the meter con-
trol switches, select
and
then press
.
4
Press
or
of the meter con-
trol switches, and then select
“PBD”.
5
ON and OFF will be switched over
with presses of
on the meter
control switches.
When OFF is selected and the operations
of the power back door is made to stop
from the
of multi-information display,
unless it is set to ON, the operation of the
power back door will not return. (No
return in the engine switch operation)
NOTICE
●
Keep the lower center part of the rear
bumper clean at all times.
If the lower center part of the rear
bumper is dirty or covered with snow, the
Hands Free Power Back Door may not
operate. In this situation, clean off the dirt
or snow, move the vehicle from the cur-
rent position and then check if the Hands
Free Power Back Door operates. If it
does not operate, have the vehicle
inspected by your Lexus dealer.
●
Do not apply coatings that have a rain
clearing (hydrophilic) effect, or other
coatings, to the lower center part of
the rear bumper.
●
Do not park the vehicle near objects
that may move and contact the lower
center part of the rear bumper, such as
grass or trees.
If the vehicle has been parked for a while
near objects that may move and contact
the lower center part of the rear bumper,
such as grass or trees, the Hands Free
Power Back Door may not operate. In
this situation, move the vehicle from the
current position and then check if the
Hands Free Power Back Door operates.
If it does not operate, have the vehicle
inspected by your Lexus dealer.
●
Do not subject the rear bumper or its
surrounding area to a strong impact.
If the rear bumper or its surrounding area
has been subjected to a strong impact,
the Hands Free Power Back Door may
not operate properly.
If the Hands Free Power Back Door does
not operate in the following situations,
have the vehicle inspected by your Lexus
dealer.
• The kick sensor or its surrounding area
has been subjected to a strong impact.
• The lower center part of the rear
bumper is scratched or damaged.
●
Do not disassemble the rear bumper.
●
Do not attach stickers to the rear
bumper.
●
Do not paint the rear bumper.
●
If a bicycle carrier or similar heavy
object is attached to the power back
door, disable the Hands Free Power
Back Door (kick sensor).
Canceling the power back door
system
112
3-2. Opening, closing and locking the doors
The Hands Free Power Back Door
(kick sensor) can be enabled/disabled
on the multi-information display.
(
1
Press
or
of the meter con-
trol switches and select
.
2
Press
or
of the meter con-
trol switches, select the “Vehicle
Settings” and then press
.
3
Press
or
of the meter con-
trol switches, select
and
then press
.
4
Press
or
of the meter con-
trol switches, and then select “Kick
Sensor”.
5
ON and OFF will be switched over
with presses of
on the meter
control switches.
When OFF is selected and the operations
of the Hands Free Power Back Door is
made to stop from the
of multi-infor-
mation display, unless it is set to ON, the
operation of the Hands Free Power Back
Door will not return. (No return in the
engine switch operation)
The open position of the power back-
door can be adjusted.
1
Stop the power back door at the
desired position. (
2
Press and hold the
switch on
the lower part of the power back
door for 2 seconds.
When setting is complete, a buzzer
will sound 4 times.
The next time the power back door
is opened, it will stop at that position.
■
Returning the power back door opening
position to the default setting
Press and hold the
switch on the
lower part of the power back door for 7
seconds.
A buzzer will sound twice. The next time
the power back door is opened, it will open
to the default position.
■
Customization
The opening position can be set with the
navigation system or multimedia system.
Priority for the stop position is given to the
last position set by either the
switch,
navigation system or multimedia system.
(Customizable features:
Canceling the Hands Free
Power Back Door (if equipped)
Adjusting the open position of
the power back door
113
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
■
Antenna location
Antennas outside the cabin
Antennas inside the cabin
Antenna outside the luggage compart-
ment
■
Effective range (areas within which the
electronic key is detected)
When locking or unlocking the doors
The system can be operated when the
electronic key is within about 2.3 ft. (0.7 m)
of an outside door handle. (Only the doors
detecting the key can be operated.)
When starting the engine or changing
engine switch modes
The system can be operated when the
electronic key is inside the vehicle.
■
Alarms and warning messages
An alarm sounds and warning messages
are displayed on the multi-information dis-
play to protect against unexpected acci-
dents or theft of the vehicle resulting from
erroneous operation. When a warning mes-
sage is displayed, take appropriate mea-
sures based on the displayed message.
(
When only an alarm sounds, circumstances
and correction procedures are as follows.
●
When an exterior alarm sounds once for
5 seconds
●
When an interior alarm sounds continu-
ously
Smart access system with
push-button start
The following operations can be
performed simply by carrying the
electronic key on your person, for
example in your pocket. The driver
should always carry the electronic
key.
Locks and unlocks the doors
(
Locks and unlocks the back door
(
Starts and stops the engine
(
A
B
C
Situation
Correction
procedure
An attempt was made to
lock the vehicle while a
door was open.
Close all of the
doors and lock
the doors
again.
A
B
114
3-2. Opening, closing and locking the doors
■
If “Key Left inside Vehicle” is shown on
the multi-information display
An attempt was made to lock the doors
using the smart access system with
push-button start while the electronic key
was still inside the vehicle. Retrieve the elec-
tronic key from the vehicle and lock the
doors again.
■
Battery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key
battery and the battery from being dis-
charged while the vehicle is not in operation
for a long time.
●
In the following situations, the smart
access system with push-button start may
take some time to unlock the doors.
• The electronic key has been left in an
area of approximately 6 ft. (2 m) of the
outside of the vehicle for 10 minutes or
longer.
• The smart access system with push-but-
ton start has not been used for 5 days or
longer.
●
If the smart access system with push-but-
ton start has not been used for 14 days or
longer, the doors cannot be unlocked at
any doors except the driver’s door. In this
case, take hold of the driver’s door han-
dle, or use the wireless remote control or
the mechanical key, to unlock the doors.
■
Turning an electronic key to bat-
tery-saving mode
When battery-saving mode is set, battery
depletion is minimized by stopping the elec-
tronic key from receiving radio waves.
Press
twice while pressing and holding
. Confirm that the electronic key indica-
tor flashes 4 times.
While the battery-saving mode is set, the
smart access system with push-button start
cannot be used. To cancel the function,
press any of the electronic key buttons.
■
Conditions affecting operation
The smart access system with push-button
start, wireless remote control and engine
immobilizer system use weak radio waves.
In the following situations, the communica-
tion between the electronic key and the
vehicle may be affected, preventing the
smart access system with push-button start,
wireless remote control and engine immo-
bilizer system from operating properly.
(Ways of coping:
●
When the electronic key battery is
depleted
●
Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
●
When the electronic key is in contact
with, or is covered by the following metal-
lic objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil
inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
●
When other wireless keys (that emit radio
waves) are being used nearby
●
When carrying the electronic key
together with the following devices that
emit radio waves
• Portable radio, cellular phone, cordless
phone or other wireless communication
Situation
Correction
procedure
The engine switch was
turned to ACCESSORY
mode while the driver’s
door was open (The
driver’s door was opened
when the engine switch
was in ACCESSORY
mode).
Turn the engine
switch off and
close the
driver’s door.
115
3-2. Opening, closing and locking the doors
3
Be
fore
dri
ving
devices
• Another vehicle’s electronic key, another
electronic key of your vehicle, or a wire-
less key that emits radio waves
• Personal computers or personal digital
assistants (PDAs)
• Digital audio players
• Portable game systems
●
If window tint with a metallic content or
metallic objects are attached to the rear
window
●
When the electronic key is placed near a
battery charger or electronic devices
●
When the vehicle is parked in a pay park-
ing spot where radio waves are emitted
■
Note for the entry function
●
Even when the electronic key is within the
effective range (detection areas), the sys-
tem may not operate properly in the fol-
lowing cases:
• The electronic key is too close to the win-
dow or outside door handle, near the
ground, or in a high place when the doors
are locked or unlocked.
• The electronic key is near the ground or
in a high place, or too close to the rear
bumper center when the back door is
opened.
• The electronic key is on the instrument
panel, luggage compartment, floor, or in
the door pockets or glove box when the
engine is started or engine switch modes
are changed.
●
Do not leave the electronic key on top of
the instrument panel or near the door
pockets when exiting the vehicle.
Depending on the radio wave reception
conditions, it may be detected by the
antenna outside the cabin and the door
will become lockable from the outside,
possibly trapping the electronic key
inside the vehicle.
●
As long as the electronic key is within the
effective range, the doors may be locked
or unlocked by anyone.
●
Even if the electronic key is not inside the
vehicle, it may be possible to start the
engine if the electronic key is near the
window.
●
The doors may unlock if a large amount
of water splashes on the door handle,
such as in the rain or in a car wash when
the electronic key is within the effective
range. (The door will automatically be
locked after approximately 60 seconds if
the doors are not opened and closed.)
●
If the wireless remote control is used to
lock the doors when the electronic key is
near the vehicle, there is a possibility that
the door may not be unlocked by the
entry function. (Use the wireless remote
control to unlock the doors.)
●
Touching the door lock sensor while
wearing gloves may delay or prevent lock
operation. Remove the gloves and touch
the lock sensor again.
●
When the lock operation is performed
using the lock sensor, recognition signals
will be shown up to two consecutive
times. After this, no recognition signals
will be given.
●
If the door handle becomes wet while the
electronic key is within the effective
range, the door may lock and unlock
repeatedly. In that case, follow the follow-
ing correction procedures to wash the
vehicle:
• Place the electronic key in a location 6 ft.
(2 m) or more away from the vehicle.
(Take care to ensure that the key is not
stolen.)
• Set the electronic key to battery-saving
mode to disable the smart access system
with push-button start. (
●
If the electronic key is inside the vehicle
and a door handle becomes wet during a
car wash, a message may be shown on
the multi-information display and a
buzzer will sound outside the vehicle. To
turn off the alarm, lock all the doors.
●
The lock sensor may not work properly if
it comes into contact with ice, snow, mud,
etc. Clean the lock sensor and attempt to
operate it again.
●
A sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this case,
return the door handle to the original
position and check that the doors unlock
before pulling the door handle again.
●
If there is another electronic key in the
116
3-2. Opening, closing and locking the doors
detection area, it may take slightly longer
to unlock the doors after the door handle
is gripped.
●
Fingernails may scrape against the door
during operation of the door handle. Be
careful not to injure fingernails or dam-
age the surface of the door.
■
When the vehicle is not driven for
extended periods
●
To prevent theft of the vehicle, do not
leave the electronic key within 6 ft. (2 m)
of the vehicle.
●
The smart access system with push-but-
ton start can be deactivated in advance.
●
Setting the electronic key to battery-sav-
ing mode helps to reduce key battery
depletion. (
■
To operate the system properly
Make sure to carry the electronic key when
operating the system. Do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of the
vehicle.
Depending on the position and holding
condition of the electronic key, the key may
not be detected correctly and the system
may not operate properly. (The alarm may
go off accidentally, or the door lock preven-
tion may not operate.)
■
If the smart access system with
push-button start does not operate
properly
●
If the doors cannot be locked or unlocked
and the back door cannot be opened,
perform the following.
• Bring the electronic key close to the door
handle and perform a lock or unlock
operation.
• Bring the electronic key close to the but-
ton on the back door (
P.102) and press
the button.
• Use the wireless remote control.
If the doors cannot be locked or unlocked
by perform the above, use the mechanical
key. (
P.421) However, if the mechanical
key is used while the alarm system is set, the
warning will sound. (
●
If the engine cannot be started, refer to
■
Customization
Some functions can be customized.
(
■
If the smart access system with
push-button start has been deactivated
in a customized setting
●
Locking and unlocking the doors: Use
the wireless remote control or mechani-
cal key. (
●
Starting the engine and changing engine
switch modes:
●
Stopping the engine:
WARNING
■
Caution regarding interference with
electronic devices
●
People with implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should keep
away from the smart access system
with push-button start antennas.
(
The radio waves may affect the opera-
tion of such devices. If necessary, the
entry function can be disabled. Ask
your Lexus dealer for details, such as
the frequency of radio waves and tim-
ing of the emitted radio waves. Then,
consult your doctor to see if you
should disable the entry function.
●
Users of any electrical medical device
other than implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should con-
sult the manufacturer of the device for
information about its operation under
the influence of radio waves.
Radio waves could have unexpected
effects on the operation of such medi-
cal devices.
Ask your Lexus dealer for details on dis-
abling the entry function.
117
3-3. Adjusting the seats
3
Be
fore
dri
ving
3-3.Adjusting the seats
Seat position adjustment switch
Seat cushion (front) angle adjust-
ment switch
Vertical height adjustment switch
Seatback angle adjustment switch
Lumbar support firmness adjust-
ment switch
Lumbar support height adjustment
switch (if equipped)
Seat cushion length adjustment
switch (if equipped)
■
Power easy access system
The driver’s seat (on some models) and
steering wheel move in accordance with
engine switch mode and the driver’s seat
belt condition. (
Front seats
WARNING
■
When adjusting the seat position
●
Take care when adjusting the seat
position to ensure that other passen-
gers are not injured by the moving
seat.
●
Do not put your hands under the seat
or near the moving parts to avoid
injury. Fingers or hands may become
jammed in the seat mechanism.
●
Make sure to leave enough space
around the feet so they do not get
stuck.
■
Seat adjustment
To reduce the risk of sliding under the lap
belt during a collision, do not recline the
seat more than necessary.
If the seat is too reclined, the lap belt may
slide past the hips and apply restraint
forces directly to the abdomen, or your
neck may contact the shoulder belt,
increasing the risk of death or serious
injury in the event of an accident.
Adjustments should not be made while
driving as the seat may unexpectedly
move and cause the driver to lose control
of the vehicle.
Adjustment procedure
A
B
C
D
E
F
G
118
3-3. Adjusting the seats
Rear seats
WARNING
■
When a rear seatback is folded
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Do not fold down the rear seatbacks
while driving.
●
Stop the vehicle on level ground, apply
the parking brake and shift the shift
lever to P.
●
Do not allow anyone to sit on a folded
rear seatback or in the luggage com-
partment while driving.
●
Do not allow children to enter the lug-
gage compartment.
■
When operating the rear seatback
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Make sure that passengers are clear of
the rear seatback before operating it.
●
To prevent hands and other body parts
from being caught, keep them away
from the gaps in the seats and the mov-
ing parts of the seats when operating a
rear seatback.
●
Power seat: Do not let children oper-
ate the rear seatback. Other passen-
gers may get caught in the seat.
●
Power seat: Make sure that all passen-
gers are clear of a seat before folding
it. Do not let passengers sit in the seat
while it is being folded.
■
Seat adjustment
Second-row seats: To reduce the risk of
sliding under the lap belt during a colli-
sion, do not recline the seat more than
necessary.
If the seat is reclined excessively, the lap
belt may slide past the hips and apply
restraint forces directly to the abdomen,
or your neck may contact the shoulder
belt, increasing the risk of death or seri-
ous injury in the event of an accident.
■
After adjusting the rear seats
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Make sure that the rear seatback is
securely locked in position by lightly
pushing it back and forth.
●
Check that the seat belts are not
twisted or caught between or behind
in the rear seatback.
●
Arrange the seat belts in the proper
positions for ready use.
■
Jam protection function (power seat)
Observe the following precautions.
Failure to do so may result in death or
serious injury.
●
Never use any part of your body to
intentionally activate the jam protec-
tion function.
●
The jam protection function may not
operate if something is caught just
before the fully folded position. Be
careful so that fingers, etc. do not get
caught.
●
The jam protection function may not
operate depending on the shape or
position of the obstruction. Be careful
so that fingers, etc. do not get caught.
119
3-3. Adjusting the seats
3
Be
fore
dri
ving
Manual seat
Seatback angle adjustment lever
Seat position adjustment lever
NOTICE
■
Before folding a rear seat seatback
●
Second-row seats: Make sure to stow
the center seat seat belt buckle and
armrest before folding the second-row
seat seatbacks. (
●
Third-row seats: Make sure that the
third-row seats and trays are free of
obstructions before folding the seat-
backs. Otherwise the seat or tray may
be damaged.
Adjustment procedure (RX350)
A
B
120
3-3. Adjusting the seats
Power seat
Seatback angle adjustment switch
Seat position adjustment lever
■
The rear seatbacks can be adjusted
when (power seat)
When the rear seatback is in a position
within the range
shown in the illustra-
tion, the rear seat operation switch (rear
seat) can be used to adjust the rear seat-
back.
is where the rear seatback is at its most
upright position.
■
Fully reclining the rear seatback (power
seat)
Operate the rear seat operation switch
(rear seat) to recline the rear seatback and
stop it partway. To set the rear seatback to
the rearmost position, press the button
again.
A
B
A
B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст