Lexus LC500 (2022 year). Manual in english — page 23
390
7-2. Steps to take in an emergency
One of the following may be the cause
of the problem:
The 12-volt battery may be dis-
charged. (
P.395)
The 12-volt battery terminal con-
nections may be loose or corroded.
(
P.333)
One of the following may be the cause
of the problem:
The 12-volt battery may be dis-
charged. (
P.395)
One or both of the 12-volt battery
terminals may be disconnected.
(
P.333)
Contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer if the problem cannot be repaired,
or if repair procedures are unknown.
When the hybrid system does not start,
the following steps can be used as an
interim measure to start the hybrid sys-
tem if the power switch is functioning
normally. Do not use this starting pro-
cedure except in cases of emergency.
1
Press the parking brake switch to
check that the parking brake is set.
(
P.183)
Parking brake indicator will come on.
2
Turn the power switch to ACCES-
SORY mode.
3
Press and hold the power switch for
about 15 seconds while depressing
the brake pedal firmly.
Even if the hybrid system can be
started using the above steps, the sys-
tem may be malfunctioning. Have the
vehicle inspected by any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
The interior lights and head-
lights are dim, or the horn does
not sound or sounds at a low vol-
ume.
The interior lights and head-
lights do not turn on, or the horn
does not sound.
Starting the hybrid system in an
emergency
391
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
1
Remove the cover in the center of
the rear seat. (
P.395)
2
Pull the tab.
If you lose your keys
New genuine mechanical keys can
be made by any authorized Lexus
retailer or Lexus authorized
repairer, or any reliable repairer
using another mechanical key and
the key number stamped on your
key number plate. Keep the plate in
a safe place such as your wallet, not
in the vehicle.
NOTICE
Q
When an electronic key is lost
If the electronic key remains lost, the risk
of vehicle theft increases significantly.
Visit any authorized Lexus retailer or
Lexus authorized repairer, or any reli-
able repairer immediately with all
remaining electronic keys and the card
key that were provided with your vehicle.
If the fuel filler door cannot
be opened
If the fuel filler door opener switch
cannot be operated, the following
procedure can be used to open the
fuel filler door.
Opening the fuel filler door
WARNING
Q
After opening the fuel filler door
Make sure to put back the cover to the
center of the rear seat. Failure to do so
may cause an accident.
NOTICE
Q
After opening the fuel filler door
O
Secure the tab in its original position.
392
7-2. Steps to take in an emergency
Q
When the electronic key does not work
properly
O
Make sure that the smart entry & start
system has not been deactivated using
the Remote Touch or at any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer. If it is
off, turn the function on.
O
Check if battery-saving mode is set. If it is
set, cancel the function. (
P.127)
Use the mechanical key (
P.117) in
NOTICE
O
Install the tab so that it does not cover
the clip installation position
. Fail-
ure to do so may cause damage to the
clip and make it impossible to install
the cover.
A
If the electronic key does not
operate properly
If communication between the
electronic key and vehicle is inter-
rupted (
P.127) or the electronic
key cannot be used because the
battery is depleted, the smart entry
& start system and wireless remote
control cannot be used. In such
cases, the doors and trunk can be
opened and the engine <hybrid sys-
tem> can be started by following
the procedure below.
NOTICE
Q
In case of a smart entry & start system
malfunction or other key-related
problems
Take your vehicle with all the electronic
keys (including the card key) provided
with your vehicle, to any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer as soon
as possible.
Locking and unlocking the
doors, opening the trunk and
using the key linked functions
393
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
order to perform the following opera-
tions:
Q
Locking and unlocking the door
1
Push in the depression on the front
edge of the driver’s door handle.
2
Insert the mechanical key while
pulling on the driver’s door handle.
3
Turn the key in order to perform
the following operations.
Locks both side doors
Closes the windows (turn and
hold)
*
Unlocks both side doors
Opens the windows (turn and
hold)
*
*
: These settings must be customized at
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
Q
Opening the trunk
Unlock the doors, and press the trunk
opener switch.
1
Depress the brake pedal.
2
Touch the Lexus emblem side of
the electronic key to the engine
switch <power switch>.
When the electronic key is detected, a
buzzer sounds and the engine switch
<power switch> will turn to IGNITION ON
mode <ON mode>.
When the smart entry & start system is
deactivated in customization setting, the
engine switch <power switch> will turn to
A
B
C
D
WARNING
Q
When using the mechanical key and
operating the power windows
Operate the power window after check-
ing to make sure that there is no possibil-
ity of any passenger having any of their
body parts caught in the window.
Also, do not allow children to operate the
mechanical key. It is possible for children
and other passengers to get caught in
the power window.
Starting the engine <hybrid sys-
tem>
394
7-2. Steps to take in an emergency
ACCESSORY mode.
3
Firmly depress the brake pedal and
check that
is shown on the
multi-information display.
4
Press the engine switch <power
switch>.
In the event that the engine <hybrid
system> still cannot be started, contact
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
Q
Stopping the engine <hybrid system>
Set the parking brake, shift the shift position
to P and press the engine switch <power
switch> as you normally do when stopping
the engine <hybrid system>.
Q
Electronic key battery
As the above procedure is a temporary
measure, it is recommended that the elec-
tronic key battery be replaced immediately
when the battery is depleted. (
P.351)
Q
Alarm (if equipped)
Using the mechanical key to lock the doors
will not set the alarm system.
If a door is unlocked using the mechanical
key when the alarm system is set, the alarm
may be triggered.
Q
Changing engine switch <power switch>
modes
Release the brake pedal and press the
engine switch <power switch> in step
3
above.
The engine <hybrid system> does not start
and modes will be changed each time the
switch is pressed. (
P.159, 164)
395
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
Use the mechanical key (
P.117) in
order to perform the following opera-
tions:
Q
Locking and unlocking the doors
P.392
Q
Opening the trunk
1
Slide the rear passengers’ seat
belts towards the outside.
2
Insert your fingers at the positions
marked
and pull towards you to
remove the cover in the center of
the rear seat.
3
Insert the mechanical key into the
cylinder and turn it clockwise to
open.
If the 12-volt battery is dis-
charged
The following procedures may be
used to start the engine <hybrid sys-
tem> or opening the doors, trunk or
glove box if the 12-volt battery is
discharged.
You can also call any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
Locking and unlocking the doors
and opening the trunk
A
WARNING
Q
After unlocking the trunk
Make sure to put back the cover to the
center of the rear seat. Failure to do so
may cause an accident.
396
7-2. Steps to take in an emergency
The glove box can be opened by per-
forming the following operations after
unlocking the doors.
If the glove box is locked, unlock it with the
mechanical key. (
P.294)
1
Remove the cover using a flathead
screwdriver.
To prevent damage to the cover, cover the
tip of the screwdriver with a rag.
2
Push the flathead screwdriver into
the part shown in the illustration to
open the glove box.
Q
After opening the glove box
The glove box can be opened normally by
closing the glove box after restarting the
engine <hybrid system>.
If you have a set of jumper (or booster)
cables and a second vehicle with a 12-
volt battery, you can jump start your
vehicle using the following procedure.
1
Confirm that the electronic key
(including the card key) is being
carried.
When connecting the jumper (or booster)
cables, depending on the situation, the
alarm may activate and doors locked.
(
P.80)
NOTICE
Q
When installing the cover in the cen-
ter of the rear seat
Make sure that the seat belts are not
caught in the cover. Failure to do so may
cause damage to the cover installation
clip and make it impossible to install the
cover.
Opening the glove box
Restarting the engine <hybrid
system>
397
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
2
Open the hood (
P.323) and
open the fuse box cover.
Push the tab in and lift the lid off.
LC500 (Left-hand drive vehicles)
LC500 (Right-hand drive vehicles)
LC500h (Left-hand drive vehicles)
LC500h (Right-hand drive vehi-
cles)
3
Open the exclusive jump starting
terminal cover.
LC500 (Left-hand drive vehicles)
LC500 (Right-hand drive vehicles)
398
7-2. Steps to take in an emergency
LC500h (Left-hand drive vehicles)
LC500h (Right-hand drive vehi-
cles)
4
Remove the engine cover.
LC500
LC500h
5
Connect a positive jumper cable clamp to
on your vehicle and connect the
clamp on the other end of the positive cable to
on the second vehicle.
Then, connect a negative cable clamp to
on the second vehicle and con-
nect the clamp at the other end of the negative cable to
.
A
B
C
D
399
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
LC500 (Left-hand drive vehicles)
LC500 (Right-hand drive vehicles)
400
7-2. Steps to take in an emergency
LC500h (Left-hand drive vehicles)
LC500h (Right-hand drive vehicles)
Exclusive jump starting terminal (your vehicle)
Positive (+) battery terminal (second vehicle)
Negative (-) battery terminal (second vehicle)
Solid, stationary, unpainted metallic point away from the exclusive jump starting
terminal and any moving parts as shown in the illustration
6
Start the engine of the second vehi-
cle. Increase the engine speed
slightly and maintain at that level for
approximately 5 minutes to
recharge the 12-volt battery of your
vehicle.
A
B
C
D
401
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
7
Open and close any of the door of
your vehicle with the engine switch
<power switch> off.
8
Maintain the engine speed of the
second vehicle and start the engine
<hybrid system> of your vehicle by
turning the engine switch <power
switch> to IGNITION ON mode
<ON mode>.
9
Once the vehicle’s engine <hybrid
system> has started, remove the
jumper cables in the exact reverse
order from which they were con-
nected.
10
Close the exclusive jump starting
terminal cover, and reinstall the
fuse box cover and engine cover to
its original position.
Once the engine <hybrid system> starts,
have the vehicle inspected at any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer as soon as
possible.
Q
Starting the engine <hybrid system>
when the 12-volt battery is discharged
The engine <hybrid system> cannot be
started by push-starting.
Q
To prevent 12-volt battery discharge
O
Turn off the headlights and the audio sys-
tem while the engine <hybrid system> is
stopped.
O
Turn off any unnecessary electrical com-
ponents when the vehicle is running at a
low speed for an extended period, such
as in heavy traffic.
Q
When the 12-volt battery is removed or
discharged
O
Information stored in the ECU is cleared.
When the 12-volt battery is depleted,
have the vehicle inspected at any autho-
rized Lexus retailer or Lexus authorized
repairer.
O
Some systems may require initialization.
(
P.437)
Q
When removing the 12-volt battery ter-
minals
When the 12-volt battery terminals are
removed, the information stored in the
ECU is cleared. Before removing the 12-
volt battery terminals, contact any autho-
rized Lexus retailer or Lexus authorized
repairer.
Q
Charging the 12-volt battery
The electricity stored in the 12-volt battery
will discharge gradually even when the
vehicle is not in use, due to natural dis-
charge and the draining effects of certain
electrical appliances. If the vehicle is left for
a long time, the 12-volt battery may dis-
charge, and the engine <hybrid system>
may be unable to start. (The 12-volt battery
recharges automatically during driving.)
Q
When recharging or replacing the 12-
volt battery
O
In some cases, it may not be possible to
unlock the doors using the smart entry &
start system when the 12-volt battery is
discharged. Use the wireless remote
control or the mechanical key to lock or
unlock the doors.
O
The engine <hybrid system> may not start
on the first attempt after the 12-volt bat-
tery has recharged but will start normally
after the second attempt. This is not a
malfunction.
O
The engine switch <power switch> mode
is memorized by the vehicle. When the
12-volt battery is reconnected, the sys-
tem will return to the mode it was in
before the 12-volt battery was dis-
charged. Before disconnecting the 12-
volt battery, turn the engine switch
<power switch> off.
If you are unsure what mode the engine
switch <power switch> was in before the
12-volt battery discharged, be especially
careful when reconnecting the 12-volt
battery.
O
If the 12-volt battery discharges, it may
402
7-2. Steps to take in an emergency
not be possible to shift the shift position to
other positions.
In this case, the vehicle cannot be towed
without lifting both rear wheels because
the rear wheels will be locked. (
P.366)
Q
When replacing the 12-volt battery
O
Use a Central Degassing type 12-volt
battery (European Regulations).
O
LC500: Use a 12-volt battery that the
case size is same as the previous one
(LN4), 20 hour rate capacity (20HR) is
equivalent (80Ah) or greater, and per-
formance rating (CCA) is equivalent
(685A) or greater.
LC500h: Use a 12-volt battery that the
case size is same as the previous one
(LN3), 20 hour rate capacity (20HR) is
equivalent (70Ah) or greater, and per-
formance rating (CCA) is equivalent
(600A) or greater.
• If the sizes differ, the 12-volt battery can-
not be properly secured.
• If the 20 hour rate capacity is low, even if
the time period where the vehicle is not
used is a short time, the 12-volt battery
may discharge and engine <hybrid sys-
tem> may not be able to start.
O
Use a 12-volt battery with a handle. If a
12-volt battery without a handle is used,
removal is more difficult.
O
After exchanging, firmly attach the fol-
lowing items to the exhaust hole of the
12-volt battery.
• Use the exhaust hose that was attached
to the 12-volt battery before exchanging.
• Use the exhaust hole plug included with
the 12-volt battery exchanged or the one
installed on the battery prior to the
exchange. (Depending on the 12-volt
battery to be exchanged, the exhaust
hole may be plugged.)
Exhaust hole plug
Exhaust hole
Exhaust hose
For details, consult any authorized Lexus
retailer or Lexus authorized repairer.
WARNING
Q
When removing the 12-volt battery
terminals
Always remove the negative (-) terminal
first. If the positive (+) terminal contacts
any metal in the surrounding area when
the positive (+) terminal is removed, a
spark may occur, leading to a fire in addi-
tion to electrical shocks and death or
serious injury.
Q
Avoiding 12-volt battery fires or
explosions
Observe the following precautions to
prevent accidentally igniting the flamma-
ble gas that may be emitted from the 12-
volt battery:
O
Make sure each jumper cable is con-
nected to the correct terminal and that
it is not unintentionally in contact with
any other than the intended terminal.
A
B
C
403
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
WARNING
O
Do not allow the other end of the
jumper cable connected to the “+” ter-
minal to come into contact with any
other parts or metal surfaces in the
area, such as brackets or unpainted
metal.
O
Do not allow the + and - clamps of the
jumper cables to come into contact
with each other.
O
Do not smoke, use matches, cigarette
lighters or allow open flame near the
12-volt battery.
O
If the 12-volt battery fluid level is
excessively low (
P.333), do not use
the 12-volt battery.
Q
12-volt battery precautions
The 12-volt battery contains poisonous
and corrosive acidic electrolyte, while
related parts contain lead and lead com-
pounds. Observe the following precau-
tions when handling the 12-volt battery:
O
When working with the 12-volt battery,
always wear safety glasses and take
care not to allow any 12-volt battery
fluids (acid) to come into contact with
skin, clothing or the vehicle body.
O
Do not lean over the 12-volt battery.
O
In the event that 12-volt battery fluid
comes into contact with the skin or
eyes, immediately wash the affected
area with water and seek medical
attention.
Place a wet sponge or cloth over the
affected area until medical attention
can be received.
O
Always wash your hands after han-
dling the 12-volt battery support, ter-
minals, and other battery-related
parts.
O
Do not allow children near the 12-volt
battery.
Q
After recharging the 12-volt battery
Have the 12-volt battery inspected at any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer as soon as possible. If the 12-volt
battery is deteriorating, continued use
may cause the 12-volt battery to emit a
malodorous gas, which may be detri-
mental to the health of passengers.
Q
When exchanging the 12-volt battery
After exchanging, securely attach the
exhaust hose and exhaust hole plug to
the exhaust hole of the exchanged 12-
volt battery. If not properly installed,
gases (hydrogen) may leak into the vehi-
cle interior, and there is the possible dan-
ger of the gas igniting and exploding.
NOTICE
Q
When handling jumper cables
When connecting the jumper cables,
ensure that they do not become entan-
gled in the cooling fan or engine drive
belt.
Q
To prevent damaging the vehicle
The exclusive jump starting terminal is to
be used when charging the 12-volt bat-
tery from another vehicle in an emer-
gency. It cannot be used to jump start
another vehicle.
404
7-2. Steps to take in an emergency
1
Stop the vehicle in a safe place and
turn off the air conditioning system,
and then stop the engine.
2
If you see steam:
Carefully lift the hood after the
steam subsides.
If you do not see steam:
Carefully lift the hood.
3
After the engine has cooled down
sufficiently, inspect the hoses and
radiator core (radiator) for any
leaks.
Radiator
Cooling fan
If a large amount of coolant leaks, immedi-
ately contact any authorized Lexus retailer
or Lexus authorized repairer, or any reli-
able repairer.
4
The coolant level is satisfactory if it
is between the “F” and “L” lines on
the reservoir.
Reservoir
“F” line
“L” line
Coolant inlet cap
5
Add coolant if necessary.
Water can be used in an emergency if
If your vehicle overheats
(LC500)
The following may indicate that
your vehicle is overheating.
The engine coolant temperature
gauge (
P.92) is in the red zone
or a loss of engine power is expe-
rienced. (For example, the vehicle
speed does not increase.)
“Engine Coolant Temp High Stop
in a Safe Place See Owner’s
Manual” is shown on the multi-
information display.
Steam comes out from under the
hood.
Correction procedures
A
B
A
B
C
D
405
7
7-2. Steps to take in an emergency
Wh
en
troubl
e ar
ises
coolant is unavailable.
6
Start the engine and turn the air
conditioning system on to check
that the radiator cooling fan oper-
ates and to check for coolant leaks
from the radiator or hoses.
The fan operates when the air conditioning
system is turned on immediately after a
cold start. Confirm that the fan is operating
by checking the fan sound and air flow. If it
is difficult to check these, turn the air con-
ditioning system on and off repeatedly.
(The fan may not operate in freezing tem-
peratures.)
7
If the fan is not operating:
Stop the engine immediately and
contact any authorized Lexus
retailer or Lexus authorized
repairer, or any reliable repairer.
If the fan is operating:
Have the vehicle inspected at the
nearest authorized Lexus retailer
or Lexus authorized repairer, or
any reliable repairer.
Q
When adding coolant
Add coolant in accordance with the follow-
ing procedure.
1
Remove the service cover.
2
Remove the engine cover.
3
Remove the caps
and
.
4
Add coolant through the inlet of the cap
up to the “F” line
, and then
replace the cap
.
5
Add coolant through the inlet of the cap
until it is full, and then replace the
cap .
A
B
A
C
A
B
B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст