Lexus GS300/400 (2000 year). Manual — part 266
SA0S0–04
F02397
F03451
SST
F01997
SST
SST
F03428
SA–46
–
SUSPENSION AND AXLE
REAR AXLE CARRIER
2046
DISASSEMBLY
1.
REMOVE DUST DEFLECTOR
Using a screwdriver, remove the dust deflector.
2.
REMOVE AXLE HUB
(a)
Remove the 2 bolts and nuts.
(b)
Mount the axle carrier in a vise.
HINT:
Use a set of soft jaws in the vise to protect the axle carrier.
NOTICE:
Do not tighten the vise too tight.
(c)
Using SST, remove the axle hub from the axle carrier.
SST
09520–00031
(d)
Remove the backing plate.
(e)
Using SST, remove the bearing inner race from the axle
hub.
SST
09950–00020, 09950–60010 (09951–00480),
09950–40011 (09951–04020, 09952–04010,
09953–04030, 09954–04020, 09955–04041)
NOTICE:
Be careful not to the damage the axle hub.
3.
REMOVE HUB BEARING
(a)
Using snap ring pliers, remove the snap ring.
F01998
SST
–
SUSPENSION AND AXLE
REAR AXLE CARRIER
SA–47
2047
(b)
Using SST and a press, remove the hub bearing from the
axle carrier.
SST
09950–60010 (09951–00650),
09950–70010 (09951–07100)
SA0S1–01
F02001
SST
SST
F02002
SST
SST
F02003
SST
SA–48
–
SUSPENSION AND AXLE
REAR AXLE CARRIER
2048
REASSEMBLY
1.
INSTALL HUB BEARING
(a)
Using SST and a press, install a new hub bearing to the
axle carrier.
SST
09527–17011, 09950–60020 (09951–00810),
09950–70010 (09951–07100)
(b)
Using snap ring pliers, install the snap ring to the axle car-
rier.
2.
INSTALL AXLE HUB
(a)
Install the backing plate with the 2 bolts and nuts.
Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)
(b)
Using SST and a press, install the axle hub to the axle
carrier.
SST
09527–17011, 09950–60010 (09551–00650),
09950–70010 (09951–07100)
3.
INSTALL DUST DEFLECTOR
Using SST and a hammer, install a new dust deflector to the
axle carrier.
SST
09527–17011, 09950–60020 (09951–01030),
09950–70010 (09951–07100)
HINT:
Align the speed sensor installation hole of dust deflector and
that of axle carrier.
SA0S4–01
F03421
Suspension Member Brace
Drive Shaft
x6
Lock Cap
Outboard Joint with Driver Shaft
Cotter Pin
Boot Clamp
No.2 Dust Deflector
Inboard Joint End Cover
Gasket
Washer
289 (2,950, 213)
110 (1,120, 81)
75 (765, 55)
Boot Clamp
Boot
Snap Ring
Inboard Joint Cover
Boot Clamp
Boot Clamp
Boot
Inboard Joint
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
83 (850, 61)
50 (510, 37)
–
SUSPENSION AND AXLE
REAR DRIVE SHAFT
SA–51
2051
REAR DRIVE SHAFT
COMPONENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст