Lexus GS300/400 (2000 year). Manual — part 139
EM0DD–03
A02689
SST
A02688
Bushing bore diameter
mm (in.)
10.985 – 11.006 mm
(0.4325 – 0.4333 in.)
11.035 – 11.056 mm
(0.4344 – 0.4353 in.)
Both intake and exhaust
Bushing
size
Use STD
Use O/S
0.05
A02744
SST
P04791
Intake
Exhaust
38.5 mm
(1.516 in.)
40.5 mm
(1.594 in.)
EM–48
–
ENGINE MECHANICAL (2JZ–GE)
CYLINDER HEAD
1402
REPLACEMENT
REPLACE VALVE GUIDE BUSHINGS
(a)
Using SST and a hammer, tap out the guide bushing.
SST
09201–10000 (09201–01060),
09950–70010 (09951–07100)
(b)
Using a caliper gauge, measure the bushing bore diame-
ter of the cylinder head.
(c)
Select a new guide bushing (STD or O/S 0.05).
If the bushing bore diameter of the cylinder head is greater than
11.006 mm (0.4333 in.), machine the bushing bore to the follow-
ing dimension:
11.035 – 11.056 mm (0.4344 – 0.4353 in.)
If the bushing bore diameter of the cylinder head is greater than
11.056 mm (0.4353 in.), replace the cylinder head.
(d)
Using SST and a hammer, tap in a new guide bushing to
the specified protrusion height.
SST
09201–10000 (09201–01060),
09950–70010 (09951–07100)
Protrusion height:
Intake
12.3 – 12.7 mm (0.484 – 0.500 in.)
Exhaust
11.4 – 11.8 mm (0.449 – 0.465 in.)
HINT:
Different bushings are used for the intake and exhaust.
A02687
Sharp
6 mm
Reamer
–
ENGINE MECHANICAL (2JZ–GE)
CYLINDER HEAD
EM–49
1403
(e)
Using a sharp 6 mm reamer, ream the guide bushing to
obtain the standard specified clearance (See page
) between the guide bushing and valve stem.
EM0D2–04
A11131
(d)
(g)
(f)
(e)
(b)
(c)
A11130
(h)
(i)
(j)
(k)
A11129
(o)
(n)
(o)
–
ENGINE MECHANICAL (2JZ–GE)
VALVE CLEARANCE
EM–5
1359
VALVE CLEARANCE
ADJUSTMENT
HINT:
Inspect and adjust the valve clearance when the engine is cold.
1.
REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2.
DRAIN ENGINE COOLANT
3.
REMOVE INTAKE AIR RESONATOR
4.
REMOVE THROTTLE BODY AND INTAKE AIR
CONNECTOR ASSEMBLY
(a)
Disconnect the accelerator cable from the throttle body.
(b)
Disconnect the engine wire clamp from the clamp bracket
of the throttle body.
(c)
Disconnect the engine wire from the clamp on the throttle
body bracket.
(d)
Disconnect the accelerator pedal position sensor con-
nector.
(e)
Disconnect the throttle control motor connector.
(f)
Disconnect the throttle position sensor connector.
(g)
Disconnect the air assist hose from the intake air connec-
tor.
(h)
Disconnect the PCV hose from the intake air connector.
(i)
Disconnect the VSV connector for EVAP.
(j)
Disconnect the EVAP hose (from charcoal canister) from
the VSV for EVAP.
(k)
Disconnect the vacuum hose (from No.2 vacuum pipe)
from the No.1 vacuum pipe.
(l)
Remove the 2 nuts holding the throttle body bracket to the
cylinder head.
(m)
Remove the 4 bolts and 2 nuts holding the intake air con-
nector to the air intake chamber.
(n)
Disconnect the vacuum hose (from actuator for ACIS)
from the No.1 vacuum pipe.
(o)
Disconnect the 2 water bypass hoses from the throttle
body, and remove the throttle body together with the in-
take air connector and gasket.
A02638
A02651
A02664
EX
IN
1
3
5
2
4
1
3
5
2
4
1
1
EM–6
–
ENGINE MECHANICAL (2JZ–GE)
VALVE CLEARANCE
1360
5.
REMOVE NO.3 TIMING BELT COVER
Using a 5 mm hexagon wrench, remove the 4 bolts, oil filler cap,
timing belt cover and gasket.
6.
REMOVE IGNITION COILS AND HIGH–TENSION
CORD SET ASSEMBLY (See page
7.
REMOVE SPARK PLUGS
8.
DISCONNECT ENGINE WIRE FROM CYLINDER HEAD
COVERS
9.
REMOVE CYLINDER HEAD COVERS
(See page
10.
SET NO.1 CYLINDER TO TDC/COMPRESSION
(a)
Turn the crankshaft pulley and align its groove with the
timing mark ”0” of the No.1 timing belt cover.
NOTICE:
Always turn the crankshaft clockwise.
(b)
Check that the timing marks of the camshaft timing pul-
leys are aligned with the timing marks of the No.4 timing
belt cover.
If not, turn the crankshaft 1 revolution (360
°
).
11.
INSPECT VALVE CLEARANCE
(a)
Check only those valves indicated in the illustration.
Using a feeler gauge, measure the clearance be-
tween the valve lifter and camshaft.
Record the valve clearance measurements of those
that are out of specification. They will be used later
to determine the required replacement adjusting
shim.
Valve clearance (Cold):
Intake
0.15 – 0.25 mm(0.006 – 0.010 in.)
Exhaust
0.25 – 0.35 mm (0.010 – 0.014 in.)
(b)
Turn the crankshaft pulley 1 revolution (360
°
), and align
the groove with the timing mark ”0” of the No.1 timing belt
cover.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст