Lexus GS300/400 (2000 year). Manual — part 208
SF0NE–05
B08978
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
VSV Connector for EVAP
Cover
EVAP Hose
EVAP Pipe
32 .5 (325, 24)
Fuel Pressure
Pulsation Damper
Vacuum Hose
Gasket
Fuel Inlet Pipe
No.2 Vacuum Pipe
Engine Cover
–
SFI (2JZ–GE)
FUEL PRESSURE PULSATION DAMPER
SF–25
1491
FUEL PRESSURE PULSATION DAMPER
COMPONENTS
SF0NF–03
B09504
B01582
B09505
SST
SF–26
–
SFI (2JZ–GE)
FUEL PRESSURE PULSATION DAMPER
1492
REMOVAL
1.
REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2.
DISCONNECT CONNECTOR AND HOSES
(a)
Disconnect the VSV connector for the EVAP.
(b)
Disconnect the EVAP hose from the EVAP pipe.
(c)
Disconnect the vacuum hose (from No.2 vacuum pipe)
from the air intake chamber.
3.
REMOVE FUEL PRESSURE PULSATION DAMPER
(a)
Remove the nut holding the No.2 vacuum pipe to the in-
take manifold.
(b)
Remove the bolt holding the fuel inlet pipe to the intake
manifold.
(c)
Using SST, remove the pulsation damper and 2 gaskets.
SST 09612–24014 (09617–24011)
CAUTION:
Put a shop towel under the delivery pipe.
Slowly loosen the pulsation damper.
SF0NG–04
B02000
New Gasket
(Large)
(Small)
New Gasket
B01582
B09504
–
SFI (2JZ–GE)
FUEL PRESSURE PULSATION DAMPER
SF–27
1493
INSTALLATION
1.
INSTALL FUEL PRESSURE PULSATION DAMPER
(a)
Install the fuel inlet pipe and pulsation damper with 2 new
gaskets.
HINT:
Different the gaskets are used for the upper (large side) and
lower (small side).
(b)
Using SST, tighten the pulsation damper.
SST
09612 – 24014 (09617 – 24011)
Torque: 32.5 N·m (325 kgf·cm, 24 ft·lbf)
(c)
Install the bolt holding the fuel inlet pipe to the intake man-
ifold.
Torque: 9.0 N·m (90 kgf·cm, 80 in.·lbf)
(d)
Install the nut holding the No. 2 vacuum pipe to the intake
manifold.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
2.
CONNECT CONNECTOR AND HOSES
(a)
Connect the vacuum hose (from No.2 vacuum pipe) to the
air intake chamber.
(b)
Connect the EVAP hose to the EVAP pipe.
(c)
Connect the VSV connector for the EVAP.
3.
INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
SF0NH–02
A07216
Location of Fuel Tank Cushion
Fuel Sender
Gauge
EVAP Hose
Hose Clamp
Fuel Inlet Pipe
Fuel Tank Cap
Shield
Ring
1.5 (15, 13 in.·lbf)
Fuel Inlet Hose
Fuel
Hose
Gasket
3.5 (36, 31 in.·lbf)
Gasket
Fuel Sub–Suction Hose
Fuel Tank
x 5
x 8
Fuel Tank
Vent Tube
Set Plate
Tube Joint
Clip
Fuel Pump
and Sender
Gauge
Assembly
Fuel Tank Main Tube
Fuel Tank Band
N·m (kgf·cm, ft·lbf) : Specified torque
Non–reusable part
39 (400, 29)
SF–28
–
SFI (2JZ–GE)
FUEL TANK AND LINE
1494
FUEL TANK AND LINE
COMPONENTS
CAUTION:
Always use new gaskets when replacing the fuel tank or component parts.
Apply the proper torque to all parts tightened
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст