Lexus RX300 (MCU15). Manual — part 536
RS0KB–01
RS–54
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
LEXUS RX300 (RM785E)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the airbag sensor assembly.
S
If the SRS has been deployed in a collision.
S
If the airbag sensor assembly has been found to be faulty in troubleshooting.
S
If the airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the airbag sensor assembly, see page RS–52 and RS–55. Be sure to
follow the correct procedure.
RS0KC–08
H05127
–
SUPPLEMENTAL RESTRAINT SYSTEM
AIRBAG SENSOR ASSEMBLY
RS–55
LEXUS RX300 (RM785E)
INSTALLATION
NOTICE:
S
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
S
Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.
S
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 9, refer to page BO–135.
1.
INSTALL AIRBAG SENSOR ASSEMBLY
(a)
Using a torx wrench, install the airbag sensor assembly
with the 3 screws.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
(b)
Connect the airbag sensor connectors.
NOTICE:
S
Connection of the connector is done after the sensor
assembly has been installed.
S
Make sure the sensor assembly is installed with the
specified torque.
S
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
S
When installing the senor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
S
After installing, shake the sensor assembly to check
that there is no looseness.
2.
INSTALL NO. 1 BRAKE
3.
INSTALL FLOOR SHIFT ASSEMBLY
4.
INSTALL LOWER NO. 2 PANEL
5.
INSTALL LOWER FINISH PANEL
RS0KD–07
H17186
Battery
Front Airbag Sensor (RH)
20 (205, 15)
Front Airbag Sensor (LH)
N·m (kgf·cm, ft·lbf)
Hold–Down Clamp
Battery Tray
: Specified torque
RS–56
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT AIRBAG SENSOR
LEXUS RX300 (RM785E)
FRONT AIRBAG SENSOR
COMPONENTS
RS0KE–04
H05129
LH:
H05130
RH:
–
SUPPLEMENTAL RESTRAINT SYSTEM
FRONT AIRBAG SENSOR
RS–57
LEXUS RX300 (RM785E)
REMOVAL
NOTICE:
S
If the wiring connector of the SRS is disconnected
with the ignition switch at ON position, DTCs will be
recorded.
S
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
S
Never reuse the sensor involved in a collision when
the SRS has deployed.
S
Never repair a sensor in order to reuse it.
1.
LH:
REMOVE FRONT AIRBAG SENSOR
(a)
Remove the hold–down clamp, battery and battery tray.
(b)
Disconnect the front airbag sensor connector.
NOTICE:
Disconnect the connector with sensor assembly installed.
(c)
Remove the 2 nuts and remove the front airbag sensor.
2.
RH:
REMOVE FRONT AIRBAG SENSOR
(a)
Disconnect the front airbag sensor connector.
NOTICE:
Disconnect the connector with sensor assembly installed.
(b)
Remove the 2 nuts and remove the front airbag sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст