Lexus RX300 (MCU15). Manual — part 332
I07425
IE
W–B
J5
J/C
ID1
W–B
M7
Sliding Roof
Control Switch
4
8
6
W–B
P
G–Y
OPN
Sliding Roof Gear
Assembly with ECU
9
10
7
M6
M6
M6
W–B
8
E
CLS
A
OPEN/DOWN
CLOSE/UP
DI–560
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
LEXUS RX300 (RM785E)
Sliding Roof Control Switch Circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If there is not the hand–held tester, begin with STEP 2.
1
Check sliding roof control switch operation.
PREPARATION:
Connect the hand–held tester to the DLC3.
CHECK:
(a)
Enter into DATALIST function of hand–held tester.
(b)
Check that switch status (ON/OFF) changes on the screen of hand–held tester as the sliding roof con-
trol switch of the vehicle is turned.
OK:
The motor operates normally.
NG
Replace sliding roof gear assembly
(See page DI–557).
OK
DI1RQ–06
I07346
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
DI–561
LEXUS RX300 (RM785E)
2
Check sliding roof control switch.
PREPARATION:
Remove sliding roof control switch.
CHECK:
Check continuity between terminals when switch operated.
OK:
Switch position
Tester connection
Specified condition
SLIDE OPEN
4 – 8
Continuity
SLIDE OFF
–
No continuity
SLIDE CLOSE
4 – 6
Continuity
TILT DOWN
4 – 8
Continuity
TILT OFF
–
No continuity
TILT UP
4 – 6
Continuity
NG
Replace sliding roof control switch.
OK
3
Check for open and short in harness and connectors between sliding roof gear
assembly and sliding roof control switch (See page IN–32
).
NG
Repair and replace harness or connector.
OK
Proceed to next circuit inspection shown on
problem symptom table (See page DI–557).
Limit
switch No.1
Sliding
Roof
Status
Fully
Opened
Sliding
Fully
Closed
Tilting
Limit
switch No.2
200 mm point from fully
opened position
DI–562
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
LEXUS RX300 (RM785E)
Sliding Roof Limit Switch Circuit
WIRING DIAGRAM
See page DI–558.
INSPECTION PROCEDURE
HINT:
If there is not the hand–held tester, begin with STEP 2.
1
Check sliding roof control switch operation (See page
DI–560
on step 1).
NG
Check sliding roof control switch circuit.
(See page DI–560)
OK
2
Check sliding roof limit switch operation.
PREPARATION:
Connect the hand–held tester to the DLC3.
CHECK:
(a)
Enter into ACTIVE TEST function of hand–held tester.
(b)
Check that ”Sliding Roof” operates as the hand–held tester directs.
(c)
At this time, check that status (ON/OFF) of limit switch No.1 and No.2 changes on the hand–held tester
screen as shown in the illustration below.
NOTICE:
Caution is necessary not to be caught in as the jam protection system does not operate during con-
ducting ACTIVE TEST.
OK:
DI1RR–04
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
DI–563
LEXUS RX300 (RM785E)
NG
Replace sliding roof gear assembly
(See page DI–557).
OK
3
Check sliding roof motor status.
PREPARATION:
Connect the hand–held tester to the DLC3.
CHECK:
(a)
Enter into ACTIVE TEST function of hand–held tester.
(b)
Check that ”Sliding Roof” operates as the hand–held tester directs.
(c)
As this time, check that motor status changes on the screen of hand–held tester as the sliding roof
switch of the vehicle is turned.
OK:
The motor operates normally.
NG
Replace sliding roof gear assembly
(See page DI–557).
OK
4
Check sliding roof glass alignment. (Mechanical malfunction)
(See page BO–118).
NG
Adjustment sliding roof (See page
BO–118)
.
OK
Replace sliding roof gear assembly
(See page DI–557).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст